Mazda TD91 79 CFZ User manual

Mazda CX-9㧙1
GENUINE
iPod INTEGRATION MODULE
HARNESS KIT F
INSTALLATION INSTRUCTIONS
Vehicle: Mazda CX-9
Parts number
䋺
TD91 79 CFZ (iPod integration module)
C9F4 V6 029 (Harness Kit F)
Thank you for purchasing a genuine Mazda accessory.
Before removal and installation, be sure to thoroughly read these instructions.
Please read the contents of this booklet in order to properly install and use the iPod integration module.
Your safety depends on it.
Keep these instructions with your vehicle records for future reference.
Note:
zThere are several WARNING and CAUTION sections in this booklet concerning
safety when installing or removing the iPod integration module. Always read and follow
them in order to prevent injuries, accidents, and possible damage to the vehicle.

WARNING: Indicates a situation in which serious injury or death could result if the
warning is ignored.
CAUTION: Indicates a situation in which bodily injury or damage to the vehicle could
result if the caution is ignored.
zDo not modify the iPod integration module.
zDo not install the iPod integration module in any way other than described in the following
instructions.
zIf in any doubt, please ask your Mazda dealer to install the accessory in order to prevent
errors in installation.
zIf you have any questions about the use of the accessory, ask your Mazda dealer for proper
advice before using it.
zMazda and its suppliers are not responsible for injuries, accidents, and damage to persons
and property that arise from the failure of the dealer or installer to follow these instructions.
zTo ensure safety and reliability of the work, installation, removal and disposal work by an
Authorized Mazda Dealership is recommended.
zBe careful not to lose removed parts, and be sure that they are kept free from scratches,
grease or other dirt.






* iPod is a trademark of Apple Inc., registered in the United States and other countries.

To the deale
r
Please turn over these instructions to the customer after installation.
To the customer
zKeep these instructions after installation. The instructions may be necessary for installing other
optional parts or removal of this accessory.
zShould the vehicle or this accessory be resold, always leave these instructions with it for the
next owner.
GB
1ED6P11A20800
F
E

Mazda CX-9㧙2
PARTS LIST
ziPod integration module (Part No.TD91 79 CFZ)
Parts Part Name Qty Parts Part Name Qty
iPod integration
module 1
㩷
iPod
connection cable 㪈

zHarness kit F (Part No. C9F4 V6 029)
Parts Part Name Qty Parts Part Name Qty Parts Part Name Qty
Harness (F) 1
㩷
Tie wrap
Large 300 mm
Small 100 mm
L 6
S 3 㩷
Pad protector
䋨50㬍100 mm䋩7
Urethane 1
㩷




ڏFlathead screwdriver
ڏSocket wrench ڏPliers ڏSoft cloth
ڏPhillips screwdriver ڏCutter knife ڏScissors ڏVinyl tape
ڏFastener remover ڏMat


















2. REQUIRED TOOLS
xBefore installation, verify that the kit includes all the following parts and that they are free of dirt, scratches,
or damage.
NOTE:
1. PARTS
3. BEFORE INSTALLATION
xTo prevent short related accidents while performing procedures, disconnect the negative battery cable
before beginning any work.
xWhen disconnecting the connector, hold the connector itself to remove while pressing the connector lock.
xDo not apply excessive force to the wiring harness as it could cause an open circuit.
xWhen locking connectors, listen for a click that will indicate they are securely locked.
xBe careful not to pinch the wiring harness. Otherwise, the wiring harness could be damaged.
xWhen removing and installing vehicle parts, make sure they are clean with no scratches. Also, be sure to
cover the vehicle body with protectors or mats when removing/installing parts to prevent scratches and dirt.
CAUTION
xRefer to the applicable Workshop Manual for removal and installation of vehicle parts. Not following the
procedures for removal/installation in the Workshop Manual could result in an accident or vehicle
malfunction.
xWhen the negative battery cable is removed, the clock, radio, trip meters and other memories will be erased.
Before performing work, record the content of the memory.
NOTE:

Mazda CX-9㧙3
4. CONNECTION DIAGRAM
5. CAUTIONS ON CONNECTION
xWhen connecting a connector, be sure to insert it straight along the guide.
The connector terminal may be bent if inserted at an angle.
CAUTION
iPod
(On market product)
AVN
iPod
integration module
Harness (F)
iPod connection cable
16 pin connector
CAN䋨+䋩
CAN䋨-䋩
NO CONNECT
To Sirius DLP (Line installation) /
Bluetooth H/F

Mazda CX-9㧙4

Negative battery cable disconnection
1. Set the selector lever to D range.
2. Disconnect the negative battery cable and wrap tape around it
to insulate.






Dashboard under cover removal (Driver side)
1. Remove the fasteners (2 locations).
2. Detach tab A (1 location) and hook (1 location) by pulling them
in the direction of the arrow.
3. Remove the dashboard under cover.






Decoration panel removal
1. Pull the decoration panel outward and detach clips A
(4 locations) and pin B (1 location).
2. Remove the decoration panel.
Front console box mat removal
1. Pull the front console box mat outward and detach tabs A
(6 locations), then remove the front console box mat.
6. VEHICLE PARTS REMOVAL
xWhen the negative battery cable is connected during
operation, it may cause electric shock or other personal
injuries. Disconnect the negative battery cable before
removal/installation.
WARNING
Tab A
Dashboard under cove
r
Hook
Fastene
r
Vehicle front
Decoration panel (LH)
Decoration panel (RH)
Clip A
Pin B
Vehicle front
Front console box mat
Tab A
Vehicle front

Mazda CX-9㧙5
Dashboard under (passenger’s side) cover removal
1. Insert fingers into the service hole and detach clips A (2
locations) and pin B (1 location) and hook (1 location) by
pulling it in the direction of the arrow.
2. Remove the dashboard under cover.







Glove compartment removal
1. Pull the stay damper in the direction shown in the figure, and
detach the connecting part between the glove compartment
and the stay damper.








2. Press the stopper in and remove it.
3. Lower the glove compartment.
4. Detach the clips from the dashboard and remove the glove
compartment.
Indicator panel removal
1. Remove the selector lever knob.
2. Pull the indicator panel upward and detach clips A (4 locations)
and tabs B (6 locations).
3. Remove the shift indicator illumination, and then remove the
indicator panel.
Clip A
Dashboard under cove
r
Pin B
Service hole
Hook
Vehicle front
Stay damper
Glove compartment
Vehicle front
Stopper
Glove compartment Clip
Vehicle front
Clip A Tab B
Selector lever knob
Indicator panel
Vehicle front

Mazda CX-9㧙6
Front console box removal
1. Remove a screw (1 location).
2. Pull the front console box outward and detach clip A (1 location)
and hooks (3 locations).
3. Disconnect the accessory socket connector.
4. Remove the front console box.



Center panel removal
1. Remove the screws (2 locations).
2. Pull the center panel outward and detach clips A (10 locations).
3. Disconnect the hazard switch connector and climate control unit
connectors.
4. Remove the center panel.

















Car navigation unit removal
1. Remove the bolt (1 location).
2. Remove the screws (4 locations).
3. Pull the navigation unit outward slowly and detach clips A (2
locations) from the dashboard.
4. Disconnect all the navigation connectors and antenna feeder,
then remove the car navigation unit.




xWhen installing the navigation unit, make sure that the
wiring harness and antenna feeder are not caught between
the navigation unit and dashboard. If the wiring harness or
the antenna feeder is caught between the navigation unit
and dashboard, it may cause malfunctions.
CAUTION
xThe ventilator grilles will be installed to the shaded areas
shown in the figure. Therefore, if a wiring harness is in the
areas, it could get caught and damaged. When installing
the center panel, completely press in the wiring harnesses
of the hazard warning switch connector in the direction of
the arrow so that the wiring harnesses will not be caught.
CAUTION
Front console box
Scre
w
Clip A
Hooks
Vehicle front
Center panel
Climate control unit connectors
Clip A
Hazard switch connecto
r
Scre
w
s
Vehicle front
Center panel
Hazard switch
Connector wiring harness
Vehicle front
Car navigation unit
Scre
w
Clip A
Antenna feede
r
Navigation unit
connectors
Vehicle front
Clip A
Scre
w
Bolt
Tightening torque: 6.99.8 N㨯m
[ 7199kgf㨯cm, 6286 in㨯lbf ]

Mazda CX-9㧙7
Information display removal
1. Remove the screws (3 locations).
2. Disconnect the information display connector and then remove
the information display.










Preparation for iPod integration module installation

1. Affix the pad protectors to the iPod integration module as shown
in the figure.


2. Affix the pad protectors to the iPod integration module as shown
in the figure.









3. Connect the harness (F) and iPod connection cable to the iPod
integration module.



7. INSTALLATION AND WIRING
xTo ensure proper affixing, be sure to degrease the area
where the pad protector is affixed.
CAUTION
Information display
Screws
Vehicle front
iPod integration module
Pad protector㩷
Pad protector㩷
iPod integration module㩷
iPod integration module
Harness (F)㩷
iPod connection cable㩷
xTo ensure proper affixing, be sure to degrease the area
where the pad protector is affixed.
CAUTION

Mazda CX-9㧙8
WIRING <Installation of iPod integration module>
iPod connection cable
Electro tap
To Sirius, B/T
To AVN㩷
iPod integration module
iPod connection cable
Tie wrap (large)
Vehicle front
iPod integration module
Dashboard membe
r
Vehicle front
Display 12 pin connector
(Vehicle wire ) (wire color)
Kit wire
(wire color)
㩷
Terminal J (Red/Yellow) CAN (+) (Red)㩷
Terminal L (Blue/Yellow) CAN (-) (Black)㩷
Tie wrap (small) Urethane
Electro taps
Terminal J: CAN (+) (Red/Yellow)
Kit wire: CAN (+) (Red)
Terminal L: CAN (-) (Blue/Yello
w
)
Kit wire: CAN (-) (Black)
L J
[ Information display 12-pin connecto
r
]
Pad protector
Information
display connector
Vehicle
wiring harness
xTo prevent an open or short circuit in the wiring of the iPod integration module, be sure to route cables
avoiding sharp edges and burrs of the vehicle's sheet metal.
xTo ensure proper affixing, be sure to degrease the area where the pad protector is affixed.
xAfter fixing a cable with a tie wrap, cut off excess tie wrap using nippers. Otherwise it may interfere with
other parts causing failure or noise.
CAUTION
Harness (F)
Harness (F)
Harness (F)
Harness (F)
Tie redundant part
[Step 1]
[Step 2]
[Step 3]
Branching connection using electro-tap
Vehicle wire Latch
Kit wire
Stopper
Electro-tap
Vehicle wi
r
e
Kit wire
1. Pass the vehicle wiring
harness (CAN (+), CAN
(-)) through the
electro-tap.
2. Fold the electro-tap in
the direction of the
arrow and lock it.
3. Press fit the electro-tap
terminal using pliers.
xLock the electro-tap locking area firmly until a
click sound is heard.
xDo not reuse an electro-tap if it has been used once.
CAUTION
Vehicle front

Mazda CX-9㧙9
iPod connection cable㩷
Electro tap
To Sirius, B/T
To AVN
iPod integration module
Harness (F)
Vehicle wiring harness
Tie wrap (small)
Tie wrap (large) Tie redundant part
䋨Harness F䋩
Vehicle front
Pad protector
Front A/C unit
Harness (F)
Vehicle front
iPod connection cable
Tie wrap (large)
Vehicle wiring
harness
Vehicle
front㩷
Tie redundant part
(iPod connection cable)
Vehicle wiring harness
Vehicle front
Remove connector cover when connecting
iPod; fit connector cover when iPod is not used
Put iPod connection cable in glove box
Tie wrap (small)
Dashboard
member
Tie wrap (large)
Tie wrap (large)
iPod connection cable
Harness (F)
To Sirius, B/T
Tie redundant part
30 cm
[Step 5]
[Step 6]
[Step 7]
To AVN
[Step 4]

Mazda CX-9㧙10
1. Reconnect the negative battery cable.
8. OPERATION CHECK

xFor vehicles with a car navigation system, after connecting the battery (-) terminal and turning the
ignition switch to the ACC or ON position, do not start the engine or turn the ignition switch off while
the following display appears on the car navigation unit screen. Otherwise, the car navigation unit could
be damaged.
“Program reading: Do not turn the power off”

xWhen the battery is disconnected, the windows will not fully open and close automatically.
Perform the following procedure to resume operation:
1. Turn the ignition switch to the ON position.
2. Press the switch and fully open the window.
3. Pull up the switch and continue holding for about 2 seconds to fully close the window.
4. If the function does not operate even after the ignition switch is turned off, contact an Authorized
Mazda Dealer.
CAUTION