MecPower Tecway Big Teeth Battle User manual

OPERATION MANUAL

CONTENT
1、Specification & Technical Data...................................1
2、Spare Part List..................................................2
3、Trouble Shooting................................................10
4、Game Instruction................................................11
4-1 Game Instruction ...........................................11
4-2 Operate Menu ...............................................11
4-3 Control Signal & Instruction ...............................12
5、Part List........................................................6
5-1 Mechnical Part ...........................................6-19
5-2 Coin Assy. Part ............................................20
5-3 Coin Operator Part .........................................21
5-4 Speaker Assy. Part .........................................22
5-5 Fuse & Power Assy. Part ....................................22
5-6 Electrical Assy. Part ......................................23
5-7 Art Part ................................................16-26
5-8 Electric Part ..............................................27
6、IO Sheet.....................................................28-30

1
1、Specification & Technical Data
1) Voltage： AC 220V±10% 50Hz
2) Power Consumption：mix150W ～ max280W
3) Dimension：L2085×W990×H1945（mm）
4) Weight ：About 214kg
5) Environment：Temperature(Indoor): -10℃～+40℃；
Humidity：≤90%；
Air Pressure：86Pa～106Pa。
Warning： To re-start the machine for 1 min after power off。
Unit：mm

2
2、Spare Part List
Part List：
NO. ITEM Spec./Material QTY UNIT DRAWING REMARK
1 Manual A4 1 Pc
1258 1 Pc
Ticket
door, coin
door,
repair door
2 Key
1396 1 Pc
Coin box
3 Fuse 6.3A 1 Pc
4 Power cord 1.5M 1 Pc
5 Long micro
switch 1 Pc
6 Micro switch
3 Pc
7 Ball 10 Pc
8 Micro switch
Use for button 1 pc

3
3、Trouble Shooting
Failure Reason Solution
Can not insert
coin
Do not adjust the coin acceptor.
Have the fake coin
Adjust the coin acceptor
Take out the fake coin
No ticket out
No 12V input for ticket dispenser.
Drive signal wire loosen.
Do not put down the ticket wheel.
Ticket dispenser terminal damage.
Not for ticket out type.
Check the power supply voltage and wire.
Check the drive signal wire/
Put down the ticket wheel.
Replace the main board.
Adjust the type for ticket out.
No music
Volume is low.
Volume output wire short-circuit.
Speaker damage.
Amplifier damage.
PC board damage.
Audio connection mouth loosen or damage.
Speaker connect or not.
Adjust the volume.
Connect the wire.
Change the speaker.
Change the main board.
Change the wire.
Re-connect the audio wire.
Turn on the speaker.
No movement
No power.
Do not turn on the power switch.
The power fuse burned.
No voltage output for power supply
No power pressure for main board.
Main board damage.
Turn on and plug the power on.
Turn on the power.
Change the new fuse.
Change the power supply.
Connect the main board wire.
Change the main board.

4
4、Game Instruction
4-1 Game Instruction
1. Insert coin and start game.
2. Players move the gun(left/right,up/down) to aim the target to get
score.
3. In the game time, the higher score you get the more ticket you earn.
4. Two players mode.
4-2 Operate Menu
Gun
Gun
Ticket mouth
Teeth
Start button
Start button
Control cabinet

5
4-3 Control signal & Instruction
1. Check the attach IO sheet and diagram can see the place for output &
input on the main board.
2. DIP adjustment can refer to IO sheet, capital letter is for factory
setting, customer can adjust according to the operation suitation.
3. Main board schemation diagram：
The above instruction is subject to change without notice.

6
5、Part List
5-1 Mechanical Part
Overall
Teeth mechanic
Shooting mechanic
Light box
Ball out mechanic

7
Light box assembly
No Name Spec/Material Qty
1 Light box cover
Transparent plastic 1
2 Speaker cover 2
3 Light cover of
speaker 2
4 Plastic light box
White plastic 1
5 Speaker column
8
6 Speaker 2
7 Light barrier 1
8 F
ixer of plastic
light box
9 Back plate of
light box Plywood 1
10 Sheet metal 1
11 Light box holder
Q235 2

8
Teeth mechanism
No Name Spec/Material Qty
1 Strong magnet d6*D20*H5 3
2 Support seat Stainless steel 1
3 Tooth axis Length 380mm
chrome-plated optical axis
1
4 Septum sleeve Stainless steel 4
5 Bearing F688Z 8
6 Stop swing rod Stainless steel 1
7 Teeth PC 3
8 Teeth back plate Stainless steel 201 3
9 Back stop rod Stainless steel 201 1
10 Upper pendulum Stainless steel 201 1
11 sleeve Stainless steel 201 4
12 Joint bearing Inter tooth M6 2
13 Starting with
connecting rod Stainless steel 201 1
14 Upper teeth crank Stainless steel 201 1
15 Micro switch 1

9
16 Joint pads Stainless steel 201 4
17 Motor fixer sheet
metal Stainless steel 201 1
18 Motor 24V 25RPM 1
19
20
21
22
Shooting mechanism

10
No Item No. Name Spec/Material Qty
1 Motor ZYTD38SRZ-R(55)
24V3000RPM 2
2 Adjustment plate Stainless steel 1
3 Rib bearing F688 2
4 Synchronous tooth
plate Stainless steel 2
5 Pillar(common parts)
White nylon 4
6 Wheel for sending
ball(common parts)
silica gel 2
7 S
hooting motor wheel
seat Aluminum alloy 2
8 Pipe Q235 1
9 Limit rubber(common
parts) Polyurethane 3
10 Side vertical plate A
Q235 2
11 Side vertical plate
B(common parts) Q235 2
12 Limit block Q235 1
13 No use Connector B Stainless steel 1
14 Fixed seat Q235 1
15 throwing branch pipe
Q235 1
16 bucket Stainless steel 1
17
Copper sleeve (common
parts) brass 2
18 Motor plate Stainless steel 2
19 Left handle Black plastic 2
20 Right handle Black plastic 2

11
Sending ball mechanism
No Name Spec/Material Qty
1 Ball rack Stainless steel 201 1
2 Friction wheel A Rubber 1
3 Friction wheel seat A
Aluminum alloy 1
4 Modulation plate Stainless steel 201 1
5 Mixing ball plate motor
24V 25RPM 1
6 Sending ball motor 24V 25RPM 1
7 Mixing ball plate Stainless steel 201 1
8 Slide plate A Stainless steel 201 1
9 Slide plate B Stainless steel 201 1

12
5-2 Coin selector assembly
No Name Spec/Material Qty
1 Coin selector Electronic operated 2
2 Ticket dispenser 2
3 Ticket box White plastic 2
`4 Coin box iron 1
5 AH78 Lock 78 short lock 1
6 Counter bracket Black plastic 1
7 6 bit counter C-012 2
8 Sound regulator Black plastic 1
9 Reset button Red button 3
3
3
4
2
2
1
1
5
9
8
7
6

13
5-3 投币器说明
When the coin stuck in coin selector, pull button as shown in photo, the
coin will be withdrawn from it. If the coin can not be withdrawn, it is
necessary to open the coin acceptor and remove the coin.
Electronic operated coin selector instruction：
Ａ.Please first remove the plastic coins in the coin slot and replace
with the coin you want to use.
Ｂ. Loosen the screws on the back of the coin slot and adjust the
fixing tabs on the back of the coin slot according to the
diameter of the coin.
Ｃ. Select N.O (normally open) and N.C (normally closed) switch;
the general use is N.O (normally open).
Ｄ. Select COIN length / speed switch (TIMER SWITCH): 30MS (short
fast signal) /50MS (middle fast signal) /100MS (long slow
signal), general use is 50MS.
Ｅ. The VR knob is used to adjust the sensitivity of the coin
selection. Adjusting clockwise (+), the range of acceptable
coin tolerances is large and the counterclockwise adjustment
(-) allows for a smaller range of tolerances for coins, which
means the screening is more stringent.
Ｆ. Wiring instruction：
1. Gray wire
Red wire-DC+12V
2. White wire-COIN Signal
meter
3. Black wire-ground wire
4. Gray wire

14
5-4 Speaker assembly
No Name Spec/Material Qty
1 Round speaker 4 inch 8Ω15W 2
2 White plastic cover
Plastic 2
3 Speaker light board
Red，Green，Blue RGB 2
4 Speaker net Silver 2
5-5 Fuse and power components
No Name Spec/Material Qty
1 Wire box Black plastic 1
2 Fuse base HJMF-527 1
3 Ground terminal 1
4 Switch Black plastic 1
5 Power outlet 1
6 Power cable 6.3A 1
1
1
3
4
5
6
2
2
3
4

15
5-6 Electrical installation components
No Name Spec/Material Qty Unit
12V 150W 1
1 Power Supply
24V 150W 1
pc
pc
2 Main board SXKJ-2013.PCB VER1.0 1 pc
3 Solid state relay
SSR-10DD 2 pc
4 12V
Light control
board XXH-150703A 1 pc
5 Filter YB10A1 1 pc
6 LED SMG15102-3W.PCB V3.0 4 pc
7 Exhaust fan net
2 pc
8 Exhaust fan 1804U3A 001 12V 1 pc
9 6 bit counter C-012 2 pc
10 Counter bracket
Black plastic 1 pc
11 Sound regulator
Black plastic 1 pc
12 Repair button Red button 2 pc
13 T
ooth lamp wiring
board SY-5W.PCB V1.1 2 pc
1
4
3
5
2
8
7
6
11
9
10
12
12

16
5-7 Artwork
No. Name Spec/Material Qty
1 Image of Light box Sticker 1
2 Image on two sides of
machine Sticker Bilateral
3 Image on console Sticker 1
4 Image on front door Sticker 1
5 Main image A Sticker 1
6 Main image B Sticker 2
7 Image on shooting
mechanism Sticker 4
8 Image on back of seat Sticker 1
9 Image on two sides of seat
Sticker Bilateral
\
8
2
6
1
5
3
4
9
7

17
8
4
9
7
1
2
3
6
5

18
No. Name Spec/Material Qty
1 Ticket gate White sticker 2
2 Fork label White sticker 4
3 “Do not touch” label
White sticker 2
4 Repair label White sticker 2
5 High temp./voltage
label White sticker 1
6 High voltage label White sticker 1
7 Ground wire label White sticker 1
8 Fuse current label White sticker 1
9 Indoor use label White sticker 1
10 Name plate 1
11 IO sheet 1