MecPower Tecway Alien Fireman User manual

Alien Fireman

1
Safety Attentions
1) Certain part of the game is with high voltage. Adjust the game by
technician. Do not open the game door unless maintenance or parts
replacement is required.
2) Please switch off the power before checking and maintenance.
3) Please switch off the power before opening the game door.
4) Fire extinguisher equipment must be nearby the game.
Installation
The game must be located properly to avoid damages.
Improper Locations:

2
Notes of Usage
1) The voltage range of the game should be 105V~115V or 215V~225V.
The proper voltage should be 110V/220V. The specific voltage accords
to the date plate on the back door of the game. The voltage must be
correct; otherwise it would be difficult to repair the damage.
2) The plug must be plugged in tightly and keep the power cords not be
too tight and damaged in order to prevent bodily injury, short-circuit
and power leakage.
3) To put the machine to normal operating, please properly adjust the
coin match and the game settings when use at the first time.
4) Please regularly check all the functions of the game when operate to
prevent dysfunction.
Notes of Maintenance
1) Be sure to check and maintain the game regularly.
2) Switch off the power before replacing the parts of the game.
3) The parts for replacement should be the same model as the old one.
4) Please check the connection and voltage output after replacing the
power supply.
5) The voltage range of the PCB should be 5.1V-5.4V.
6) Check whether the game has creepage and the voltage before
repairing the PCB.

3
Notes of Clean
1) Please use clean and soft cloth to clean the game.
2) Prevent damaging the surface of the game, please do not use the
following cleanser:
Alterative Cleanser；
Acidic Cleanser；
Insecticide, sterilized water, alcohol or other chemical cleanser.
Notes of Moving and Shipping
1) Properly disassemble the game for necessary moving and shipping.
2) Prevent the game from hitting or being attrite during movement.
3) Protecting the case when move the game.

4
1. Game introduction
The Alien Fireman with unique, beautiful and comic
appearance, interesting and exciting game, it is specially
designed and developed by our company for the young people.
It will be very essential and popular in amusement center.
Features:
Realistic, colorful;
High-speed processing CPU, stable performances;
Coin mech with high quality fits for various coins.
Simple, stimulating, strong operational sense and full of entertaining.
2. Playing tips and Operations
Playing tips：
1) Ride on the seat, then insert coin(s)
2) Press the start button.
3) Move water gun to extinguish the lit up fire.

5
3. TECHNICAL PARAMETER
VOLTAGE: AC220V/110V（50/60HZ）
MAX. CURRENT: 6A
(Note: please refer to the nameplate located on the back of the
games to check actual usage of voltage.)
MAX. POWER: 1200W
STANDBY POWER: 100W
COIN SIZE：φ21mm ~ φ30mm (diameter)
1.2mm ~ 2.5mm (thickness)
LOCATION REQUIRED: -5 ~ 40℃, humidity is less than 90%. No
contact with any corrosive liquid, no any greasiness and dirt.

6
4. INSTALLATION
Please follow the direction below to install the game.
4.1 CHOOSE THE LOCATION FOR INSTALLATION
1) Put the Alien Fireman in the same type of game then select the concrete
placement according to the machine's exterior.
2) Choose the proper location for installation. It must be placed on the flat
floor to make the machine on the ground steadily.
4.2 FIX THE GAME
Screw the foundation down to hold the game machine so that the machine can
not be moved.
4.3 CHECK AND SET BEFORE CONNECTING THE POWER
1) Please check whether the parts of cabinet are loose caused by moving,
and the wire terminal should not drop out from the port.
2) Check whether the GND is connected.
3) Please check whether the resistance of power input at the both ends for
GND is more than 100 megohm.
4) Adjust the coin machine and check if it can work properly.

7
5) Make sure the machine's connected properly before power on.
Attention
A. Please make sure the power cord is not pressed by wheel, foundation,
etc. Otherwise, it will damage the wire to cause short circuit, even fire. Do
not use strong power to extend and wring the wires. Do not make the wire
be near to the high temperature object. Properly put the wire to avoid any
kicking or treading.
B. Hold the plug to pull it out from the socket. Do not touch the plug with
wet hands.
4.4 CHECK AND ADJUST AFTER CONNECTING THE POWER
1) Make sure the input voltage is same as the one stated on name plate
on the back door of the game.
2) After connecting the power, please switch on the game.
AAAA

8
3) Inserting coin to check if the coin machine cans work properly.
4) Enter into the setting program and set the game settings (include coin,
game time, etc.)
5) Check the sound if it is OK.
4.5 ADD WATER TO THE WATER TANK.
1) Please DO NOT add water from the top of the machine.
2) Turn on the power switch and open the front glass door, add about 16L
water.
Here is NOT the
water intake.
It is for the
circuitry.

9
NOTE: Please pay attention to this alarm lamp while adding water.
Stop adding water when the lamp lit up. Otherwise, the overflow water
will damage the circuitry.
***** Water level is too high: alarm lamp lit up, need to drain some water.
***** Water shortage: alarm lamp lit up and with alarm sound, need to add
water

10
5. MOVEMENT
1) Please remember to drain off the water before moving the
machine, otherwise, the water will flow out to damage the circuitry.
a. Open the front door and take out the drainpipe.
b. Turn on the tap to drain the water.

11
2) Screw the foundation to leave the ground (about 5mm)..
3) Unplug the wire and move the machine.
Note: when the road surface is uneven during moving or when you
tilt the machine, please pay attention to the strength to prevent
damage to the game machine body.
WARNING
Please power off the game first and pull out the cord, then move the game.
Please do not carefully move, turnover, transport the game; otherwise it
will destroy the game.
Prevent hitting, rubbing the games when move the games, otherwise it will
damage the appearance of the game.
6. CHECK BEFORE OPERATION
Check the game before operation to prevent the game from working
improperly when operated.
Checking item：
1) Check if the cord is securely plugged in and without defects.
2) Check the location of game.
3) Check if the game cabinet is without defects or burrs.
4) Check if the game without dirt and properly stuck on with marks

12
7. DAILY OPERATION
7.1 INPUT POWER TO OPERATE
1) Turn on the power switch.
2) Visually check the game and confirm the water gun can work properly.
3) Check the sound if it is OK.
4) Confirm the coin mech, button and the
movement is
normal.
Warning：Before operation, please confirm all the items above are OK.
7.2 COLLECT COINS AND KEEP RECORD
1) Switch off the power and open the door of the coin box to take out the
coins
2) Open the door of the coin mech to keep a record of the coins’ quantity.
wiper

13
8、GAME SETTING
There are 2 sets of DIP switches on the main board, SW1 and SW2.
Toggle “ON” or “OFF” to change the setting.
A.DIP SW1—SW2 main board.
1. How many coin(s) for 1 credit（DIP SW1）
PIN 1 PIN 2 PIN 3 PIN 4 Description
OFF OFF OFF OFF 1 coin（default）
ON OFF OFF OFF 1 coin
OFF ON OFF OFF 2 coins
ON ON OFF OFF 3 coins
OFF OFF ON OFF 4 coins
ON OFF ON OFF 5 coins
OFF ON ON OFF 6 coins
ON ON ON OFF 7 coins
OFF OFF OFF ON 8 coins
ON OFF OFF ON 9 coins
OFF ON OFF ON 10 coins
ON ON OFF ON 11 coins
OFF OFF ON ON 12 coins
ON OFF ON ON 13 coins
OFF ON ON ON 14 coins
ON ON ON ON 15 coins
2. Playing time（DIP SW1）
PIN 5 PIN 6 PIN 7 PIN 8 Description
OFF OFF OFF OFF 60s
ON OFF OFF OFF 90s（default）
OFF ON OFF OFF 120s
OFF OFF ON OFF 150s
OFF OFF OFF ON 180s

14
3. Demo interval（DIP SW2）
PIN 1 PIN 2 Description
OFF OFF Demo plays every 60s （default）
ON OFF 90s
OFF ON 120s
ON ON 180s
4. Standby show（DIP SW2）
PIN 3 Description
OFF Close the standby show（default）
ON Open the standby show

15
9. Adjustment
Adjust the coin mech
Descriptions:
Step 1: remove the plastic coin from the coin sample chute and put a proper
coin in it.
Step 2: remove the screws on the back of coin entrance. Adjust the fix chip of
back of coin entrance according to the diameter of coin you will use
so that it will prevent the large coin blocking the coin mech.
Step 3: set the COIN to “ON”
Note: when power on, set this button is for insert coin.
Step 4: set the pulse of COIN signal to “50MS”.
Step 5: following the drawing to adjust the resistance for sensitivity of coin
acceptance, turn clockwise for increasing and counterclockwise for
decreasing.
adjusting chip of entrance
coin reject bar
COIN signal wavelength
adjusting SW
COIN signal SW
power/signal input
micro-adjust resistance
sample coin chute
DC+12V
STRICT SLACK
Sensitivity
+-
COIN
Remove
REPLACE
Backward
SW3
100ms SLOW
25ms FAST
NOM
normal
MGN
accurate
50ms MEDIUM
WHITE
COUNTER(+/-)
GROUND
N.C.
SW1
SW2
N.O.
COUNTER(-/+)
COIN SIGNAL
GRAY
BLACK
RED
GRAY

10. Schematic Diagram
1 8
CN3 1 8 CN4 18
CN6 18
CN8 1 8 CN9 1 8 CN10
6
4
1
RESET
TXD
RXD
1
10
CON1
1
4
1
12
CN1
1 10
COIN1 1
8CN7
C
O
I
N
2
1
8
CN12
NC NC NC NC NC NC
1
12
33
M
M
M
4
Alien Fireman Wiring diagram
Time Score
Normally
Open
Target 1
Target 2
Target 3
Target 4
Target 5
Coin button
Free button
Start button
Low water level
Stop sensor
Drain switch
wiper up switch
wiper down switch
Solenoid valve
Water pump
Target light 1
Target light 2
Target light 3
Target light 4
Target light 5
Coin meter
Motor
Fan
Start button light
Headlights
Alarm lamp
wiper reverse
wiper forward
Solenoid valve-MegaDrop