MecPower Tecway Kiddie Pirate User manual

1
In order to prevent the variety of problems which caused by
incorrect operation，Please read the manual first before operating
this machine and pay attention to the items marked in “note”.
Please keep this manual carefully for checking when needed.
Summary
Transportation, installation, safe operation of moving and
operating methods and attentions;
Installation and operation;
Function adjustment;
Maintenance;
General troubleshooting and solutions;
Main components diagram;
Circuit connection diagram.

2
August 25th, 2011
Safety Attentions
1) Certain part of the game is with high voltage. Adjust the game by
technician. Do not open the game door unless maintenance or parts
replacement is required.
2) Please switch off the power before checking and maintenance.
3) Please switch off the power before opening the game door.
4) Fire extinguisher equipment must be nearby the game.
Installation
The game must be located properly to avoid damages.
Improper Locations:

3
Notes of Usage
1) The voltage range of the game should be 105V~115V or 215V~225V.
The proper voltage should be 110V/220V. The specific voltage accords
to the date plate on the back door of the game. The voltage must be
correct; otherwise it would be difficult to repair the damage.
2) The plug must be plugged in tightly and keep the power cords not be
too tight and damaged in order to prevent bodily injury, short-circuit
and power leakage.
3) To put the machine to normal operating, please properly adjust the
coin match and the game settings when use at the first time.
4) Please regularly check all the functions of the game when operate to
prevent dysfunction.
Notes of Maintenance
1) Be sure to check and maintance the game regularly.
2) Switch off the power before replacing the parts of the game.
3) The parts for replacement should be the same model as the old one.
4) Please check the connection and voltage output after replacing the
power supply.
5) The voltage range of the PCB should be 5.1V-5.4V.
6) Check whether the game has creepage and the voltage before
repairing the PCB.

4
Notes of Clean
1) Please use clean and soft colth to clean the game.
2) Prevent damaging the surface of the game, please do not use the
following cleanser:
Alterative Cleanser；
Acidic Cleanser；
Insecticide, sterilized water, alcohol or other chemical cleanser.
Notes of Moving and Shipping
1) Properly disassemble the game for necessary moving and shipping.
2) Prevent the game from hitting or being attrite during movement.
3) Protecting the case when move the game.

5
CONTENT
1、GAME INTRODUCTION..........................................................错误！未定义书签。
2、PLAYING TIPS AND OPERATIONS........................................错误！未定义书签。
3、TECHNICAL PARAMETER .....................................................错误！未定义书签。
4、MOVEMENT......................................................................................................... 10
5、INSTALLATION.....................................................................................................11
5.1 CHOOSE THE LOCATION FOR INSTALLATION ................. 错误！未定义书签。
5.2 CHECK AND SET BEFORE CONNECTING THE POWER... 错误！未定义书签。
5.3 CHECK AND ADJUST AFTER CONNECTING THE POWER错误！未定义书签。
6、CHECK BEFORE OPERATION...............................................错误！未定义书签。
7、DAILY OPERATION.................................................................错误！未定义书签。
7.1 INPUT POWER TO OPERATE ............................................. 错误！未定义书签。
7.2 CHECK AFTER OPERATION ............................................... 错误！未定义书签。
7.3 COLLECT COINS AND KEEP RECORD .............................. 错误！未定义书签。
8、GAME SETTING......................................................................错误！未定义书签。
8.1 KEYS FOR SETTING............................................................ 错误！未定义书签。
8.2 SETTING METHOD .............................................................. 错误！未定义书签。
8.3 SETTING DESCRIPTION ............................................... 错误！未定义书签。
9、ADJUSTMENT.........................................................................错误！未定义书签。
9.1 ADJUT THE COIN MECH ..................................................... 错误！未定义书签。
9.2 MAIN BOARD ADJUSTMENT............................................... 错误！未定义书签。
10、 CHECK AND MAINTAIN .................................. 错误！未定义书签。
10.1 DAILY CHEAK................................................................................................... 20
10.2 DAILY MAINTAIN .......................................................20
11、TROUBLESHOOTING .........................................................错误！未定义书签。
12、DIAGRAM FOR MAIN PARTS AND PARTS LIST...............错误！未定义书签。
12.1 BODT ................................................................................ 错误！未定义书签。
12.2 STEERING WHEEL .......................................................... 错误！未定义书签。
12.3 CIRCUIT BOARD .............................................................. 错误！未定义书签。
12.4 COIN DOOR ..................................................................... 错误！未定义书签。
12.5 CHASSIS ..........................................................................错误！未定义书签。
13、SCHEMATIC DIAGRAM.......................................................错误！未定义书签。

6
1. Game introduction
Kiddie Pirate with unique, beautiful and comic appearace,
interesting and exciting game, it is specially designed and
developed by our company for the young people. It will be very
essential and popular in amusement center.
Features:
Realistic, colorful, cutty outlook
Integrated main board, high-speed processing CPU, stable proformance.
High definition, high-quality LCD display.
Coin mech with high quality fits for various coins.
Simple, stimulating, strong operational sense and full of entertaining.
Beautiful Outlook
Stable transmission components
Steering wheel
High quality LED DISPLAY

7
Operating income can be adjusted according to the situation.
2. Playing tips and Operations
Playing tips：
Insert coin(s) after ride on the pirate ship. It moves up and down,
forward and backward after a few seconds. The enemy ships will
appear. Rotate the rudder or press the rudder up and down to aim
the enemy ships and press the fire button to attack the enemy
ships. The more enemy ships you hit, the high scores you get.
LED DISPLAY
ATEERING WHEEL
COIN MECH
START BUTTON

8
3. TECHNICAL PARAMETER
VOLTAGE: AC 220V/110V（50/60HZ）
MAX. CURRENT：2.5A/5A
(Note: please refer to the nameplate located on the back of the
gamesto check actual usage of voltage.)
MAX. POWER: 440W
COIN SIZE：φ21mm ~ φ30mm (diameter)
1.2mm ~ 2.5mm (thickness)
CAPACITY OF COIN BOX: 1200pcs of coins with coin
sizeφ25mm*1.5mm
LOCATION REQUIRED: -5 ~ 40 , humidity is less than 90%. No℃
contact with any corrosive liquid, no any greasiness and dirt.
DIMENSIONS: L2300mm*1150mm*H2000mm
2000
1150
2300

9
Parts shipped with tha game：
NO. DRAWING NAME SPEC./MODEL QTY
1
LED Red , green,
blue and yellow Each2
2
Pull Pole 1
3 key 1285# 2
4 key 1396# 2
5 power cord 1
6 manual 1

10
4. Movement
Direction of movement diagram:
Insert the Pull Pole to the buckle and pressure the pull pole
downward then the pirate ship move.
Pull Pole
Buckle for Pull Pole
Buckle Extension

11
WARNING
Pleaese power off the game first and pull out the cord, then move the
game.
Please do not carefully move, turnover, transport the game; otherwise it
will destroy the game.
Prevent hitting, rubbing the games when move the games, otherwise it will
damage the appearance of the game.
5. INSTALLATION
Please follow the direction below to install the game.
5.1 CHOOSE THE LOCATION FOR INSTALLATION
1) Put the Kiddie Pirate in the same type of Kiddie Ride with monitor then
select the concrete placement machine according to the machine's
exterior.
2) Choose the proper location for installation, please follow the below
drawing to install.
2.15m
3.5m
0.5m
0.5m 0.5m
0.5m

12
WARNING：It must be placed on the flat floor to meke the machine on the
ground steadily.
5.2 CHECK AND SET BEFORE CONNECTING THE POWER
1) Please check whether the parts of cabinet are loose caused by moving,
and the wire terminal should not drop out from the port.
2) Check whether the GND is connected.
3) Please check whether the resistance of power input at the both ends for
GND is more than 100 megohm.
4) Connect the wires.
Attention
A Pleasemake sure the power cord is not pressed by wheel, foundation,
etc. Otherwise, it will damage the wire to cause short circuit, even fire.
Do not use strong power to extend and wring the wires. Do not make
the wire be near to the high temperature object. Properly put the wire
to avoid any kicking or treading.
B Hold the plug to pull it out from the socket. Do not touch the plug with
AAAA

13
wet hands.
5.3 CHECK AND ADJUST AFTER CONNECTING THE POWER
1) Makesure the input voltageissame asthe one stated on nameplateon
theback door of the game.
2) After connecting the power, please switch on the game.
3) Insertingcoin to check if the coin machine cans work properly.
4) Visually check the game and confirm the displayand light can work
properly.
5) Enterintothe setting program and set the gamesettings (include coin,
game time, game levels, etc.)
6) Insert coin to play the game, confirm the operation of the direction and
the machine movement is normal
7) Check the sound if it is ok.
6、CHECK BEFORE OPERATION
Check the game before operation to prevent the gmae from working
improperly when operated.
Checking item：
1) Check if the cord is securely plugged in and without defects.

14
2) Check the location of game.
3) Check ifthe game case is without defects or burrs.
4) Check if the game without dirt and properly stuck on with marks
7、DAILY OPERATION
7.1 INPUT POWER TO OPERATE
1) Turn on the machine power switch.
2) Visually check the game and confirm the display can work properly.
3) Check the sound if it is ok.
4) confirm the coin mech , operation of the direction and the machine
movement is normal
Warning：Before operation, please confirm all the items above are ok.
7.2 CHECK AFTER OPERATION
1) Check the display of the game and confirm it is proper.
2) Double check the coin mech, operation of the direction and the
machine movement is normal, If it hasany problems, please solve the
problem as soon as possible.
7.3 COLLECT COINS AND KEEP RECORD
Switch off the power and open the door of the coin box to take out the
coins. Then open the door of the coin mechto keep a record of the coins’

15
quantity.
8、GAME SETTING
8.1 KEYS FOR SETTING
TEST: Enter into the setting menu or skipto the next menu.
ENTER: Change the setting.
SERCE: Free to play.
SW1
TEST
SERVE
SELECT
ENTER
ERASE
Setting
ree to play
Change
Setting Board

16
8.2 SETTING METHOD
Setting method: press“TEST”to enter into the game setting menu →press the
“TEST” to choose the setting item →press “ENTER” to change the setting →
press “ENTER” exit setting.
8.3 SETTING DESCRIPTION
1）Game setting interface：
Descriptions:
COIN：this setting can decide how many coins player should insert for one
game.if setting to “2”,it means insert 2 coins for 1 game.
VOLUME：this setting can decide the volume and “1” stands for the lowest.
游戏设置
币数
音量
方向盘测试
游戏时间
语言
退出
中文
2:00
5
1

17
(Note: the volume can be adjusted by adjusting the volume potentiometer on
the amplifier board.).
TIME：this setting decides the limit time for one game. if setting to “3：00”，it
means has 3 minus for one game.
Steering wheel Test：This setting is to test whether the encoder is working
noemally. When the steering wheel is turning, the number will change.
Language: This setting decides which language will be displayed in screen,
Chinese or English.
2）Steering wheel Test
Descriptions:
When the steering wheel is turning, the cursor will move in the horizontal
direction.
When pressure downward or pull upward the steering wheel，the cursor will
movein the vertical direction.
( 301, 277 )
方向盘测试
按测试键退出

18
9. ADJUSTMENT
9.1 ADJUT THE COIN MECH
Descriptions:
1): Pleasetake out the plastic coin from sample coin chute andreplace it
with token.
2): Remove the screws on back of coin entrance. Adjust the fixing chip on
back of coin entrance according to the token’s diameter, which prevent
blocking the coin mech as inserting the large coin in by mistake.
3): Turn the COIN Switch to “NO” (COIN Signal wire and GND should be
adjusting chip in
coin entrence
coin-return
pole
Adjusting Switch For
Coin Signal
Wavelength
switch for coin signal
Port For Power/Signal
Input
Micro-Resistance
sample
coin
chute
DC+12V
STRICT SLACK
Sensitivity
+-
COIN
Remove
REPLACE
Backward
SW3
100ms SLOW
25ms FAST
NOM
正常
MGN
精准
50ms MEDIUM
WHITE
COUNTER(+/-)
GROUND
N.C.
SW1
SW2
N.O.
COUNTER(-/+)
COIN SIGNAL
GRAY
BLACK
RED
GRAY

19
disconnected at usual time). Turning switch can be used as the coin
mech switch when the game is power on.
4): Adjust the adjusting switch of COIN Signalwave length to 50MS.
5): Adjust the micro-adjusting resistance of token tolerance. Clockwise:
increasing the sensitivity of token tolerence, that is, the range of
accepting the token tolerance will be larger.Counterclockwise:
decrease the sensitivity, that is, the range will be smaller and choose
the token more strictly.
9.2 MAIN BOARD ADJUSTMENT
Diagram of main board:
Descriptions:
Enulling Button: pressing this button can set the Game Setting to default
and clear the data of Coin and Ticket saved in PCB.
Volume Adjustment: Use a flat screwdriver to twist the volume
potentiometer to adjust the volume level of the machine. Turning clockwise
will increase the volume; counterclockwise will decrease the volume.

20
warning
The battery can save the data of game settings and coin number when the the
power off. Please replace the battery when the machine can not save the
game setting.
10、CHECK AND MAINTAIN
！warning
Please check and maintain the game by technicians.
Please power off the game when check and maintain.
Please do not put any tools into cabinet, otherwise it will cause problem.
After checking, please tightly screw the screws and close the door.
Dialy Check
ITEM DESCRIPTION
COIN MECH Check whether the coin mech canwork proper.
Potentiometer
of the direction
Check whether the potentiometer of the direction can
control the Kiddie Pirate’s forward direction normally
sound Check whether the sound and the volume are ok.
display Check if the displayed colors are proper.
Temperature、
humidity Check if the temperature and humidity is proper
Daily Maintenance
ITEM DESCRIPTION
THE CABINET Clean the cabinet with water and soft paper.