Metra Electronics 99-8206 User manual

INSTALLATION INSTRUCTIONS FOR PART 99-8206
Phillips Screwdriver • Socket Wrench • Cutting Tool
1-800-221-0932 www.metraonline.com
KIT FEATURES
©COPYRIGHT 2004-2009 METRA ELECTRONICS CORPORATION
APPLICATIONS
Toyota Highlander 2001-2007
4-Runner (Excluding Limited) 2003-2008
•DIN Head Unit Provision with Pocket
•ISO DIN Head Unit Provision with Pocket
A) Radio Housing • B) ISO Brackets • C) ISO Trim Plate • D) Highlander Brackets • E) 4-Runner Brackets
KIT COMPONENTS
TOOLS REQUIRED:
99-8206
B
A
D
C
E
WIRING AND ANTENNA CONNECTIONS (Sold Separately)
Harness:
• 70-1761 - Toyota harness 1987-up
•TYTO-01 -Toyota amp interface harness 2003-up
Antenna Adapter:
•Not required

Dash Disassembly
-2003-2008 Toyota 4 Runner (Excluding Limited) . . . . . . . . . 1
-2001-2007 Toyota Highlander . . . . . . . . . . . . . . . . . . . . . . . . 2
Kit Assembly
-4Runner Bracket Assembly . . . . . . . . . . . . . . . . . . . . . . . . . 3
-Toyota Highlander Bracket Assembly . . . . . . . . . . . . . . . . . . 3
-DIN Head Unit Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
-ISO DIN Head Unit Provision . . . . . . . . . . . . . . . . . . . . . . . . 5
Final Assembly .....................................6
TABLE OF CONTENTS
99-8206
K NOWLEDGE IS P OWER
Enhanceyour installation and fabrication skills
by enrolling inthe most recognized andrespected
mobile electronics school in our industry.
Log onto www.installerinstitute.com
or call 800-354-6782 formore information
and take stepstoward abetter tomorrow.

1
99-8206 DASH DISASSEMBLY
TOYOTA4RUNNER 2003-2008
(EXCLUDING LIMITED)
Disconnect the negative battery ter-
minal to prevent an accidental short
circuit.
Unsnap and remove trim from around
shifter.
Unsnap and remove trim covers from
around center console pocket edge
at front and rear of console.
1
2
Unsnap and remove entirecenter
panel around radio. (Figure D)
10
Remove (2) 10 mm bolts securing
radio to remove.
11
3
Unsnap and remove center console
cover. (Figure A)
4
Unsnap trim ring from around ignition
key cylinder.
Remove (1) 10 mm bolt from bottom
right of panel belowsteering column.
Unsnap panel and pull away to gain
access behind panel.
(Figure B)
5
6
Remove (1) 10 mm bolt on bottom
left of center panel behind panel
below steering column.
(Figure B)
7
Remove (1) 10 mm bolt beneath cli-
mate control behind pocket door.
Unsnap and remove climate control.
(Figure C)
8
Remove (2) 10 mm bolts beneath
radio behind climate controls.
9
A
B
C
D

99-8206 DASH DISASSEMBLY
2
Pull and remove dash panel from
radio and climate controls. Tip: There
are 8 clips.
(Figure A)
2
Remove (6) 10mm bolts from radio
and climate controls assembly.
(Figure B)
3
Remove assembly and disconnect
the wiring.
4
Remove (8) Phillips bolts and (4) Phillips
screws to separate brackets from assem-
bly. (Figure C)
5
A
B
C
TOYOTAHIGHLANDER 2001-2007
Disconnect the negative battery
terminal to prevent an accidental
short circuit.
1

3
4RUNNER BRACKET ASSEMBLY
TOYOTAHIGHLANDER BRACKET ASSEMBLY
Snap the appropriately marked Mounting
Brackets for your application onto the
sides of the Radio Housing. The brackets
are marked 4-Runner or Highlander and
left or right. (Figure A - 4 RUNNER)
(Figure B - HIGHLANDER)
1
B
A
99-8206 KIT DISASSEMBLY

4
99-8206
KIT ASSEMBLY
Slide the DIN cage into the Radio
Housing and secure by bending the
metal locking tabs outward. (Figure A)
1
Snap the aftermarket radio into the
cage and secure.
(Figure B)
2
DIN HEAD UNIT PROVISION WITH POCKET
A
B

5
99-8206
KIT ASSEMBLY
Mount the ISO Brackets to the head
unit with the screws supplied with
the radio. (Figure A)
1
Snap the radio into the radio housing
until the side clips engage.
(Figure B)
2
Snap the ISO Trim Plate onto the
Radio/Housing assembly.
(Figure B)
3
ISO DIN HEAD UNIT PROVISION
A
B

99-8206
FINAL ASSEMBLY
FINAL ASSEMBLY
1
Locate the factorywiring harness in the dash. Metra recommends using the
proper mating adapter and making connections as shown.
(Isolate and individually tape off the ends of any unused wires to prevent
electrical short circuit.)
2
Re-connect the negative battery terminal and test the unit for proper operation.
3
Reassemble radio and dash assemblies in reverse order of disassembly.
A
A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
D) Tape
B
C
D
Make wiring connections using the EIA color code chart shown below and the instructions included with the head
unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and individually
tape off ends of any unused wires to prevent electrical short circuit.
12V Ignition / Acc . . . Red
12V Batt / Memory . . Yellow
Ground . . . . . . . . . . . Black*
Power Antenna . . . . . Blue
Amp Turn-On . . . . . . Blue / White
Amp Ground . . . . . . . Black / White
Illumination. . . . . . . . Orange
Dimmer ..........Orange / White
Right Front (+) . . . . . White
Left Front (-). . . . . . . White / Black
Right Rear (+). . . . . . Violet
Right Rear (-) . . . . . . Violet / Black
Left Rear (+). . . . . . . Green
*NOTE: When Black a wire is not present, ground radio to vehicle chassis.
All colors may not be present on all leads due to manufacturer’s specifications.
METRA / EIA WIRING CODE
FINAL WIRING CONNECTIONS
1-800-221-0932 www.metraonline.com
REV.07/01/09 © COPYRIGHT 2004-2009 METRA ELECTRONICS CORPORATIO INST99-8206