Metra Electronics 99-7318 User manual

INSTALLATION INSTRUCTIONS FOR PART 99-7318
Phillips Screwdriver • Small Flat Blade Screwdriver
1-800-221-0932 www.metraonline.com
KIT FEATURES
©COPYRIGHT 2004-07 METRA ELECTRONICS CORPORATION
•DIN Head Unit Provision
•ISO DIN Head Unit Provision
A) Radio Housing l B) ISO Brackets l C) ISO Trim plate
KIT COMPONENTS
TOOLS REQUIRED:
99-7318
A
APPLICATIONS
2005-2006 Kia Spectra 5
BC

Dash Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Kit Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2, 3
Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
TABLE OF CONTENTS
99-7318

99-7318
1
Disconnect the negative battery
terminal to prevent an accidental
short circuit.
1
Unclip and remove entire panel sur-
rounding radio and including A/C
controls.
(Figure A)
2
2005-2006 KIA SPECTRA 5
Remove (4) Phillips screws to extract
radio from dash.
(Figure B)
3
DASH DISASSEMBLY
A
B

2
99-7318
2005-2006 KIA SPECTRA 5
KIT ASSEMBLY
Slide the DIN cage into the Radio
Housing and secure by bending the
metal locking tabs down. (Figure A)
1
Slide the aftermarket head unit into
the cage and secure.
(Figure B)
2
DIN HEAD UNIT PROVISION
A
B

99-7318
KIT ASSEMBLY
2005-2006 KIA SPECTRA 5
Mount the ISO bracket to the head
unit with screws supplied with the
unit. (Figure A)
1
Slide the head unit into the radio
opening until the side clips engage.
(Figure B)
2
ISO DIN HEAD UNIT PROVISION
A
B
3
Snap the trim plate into the radio
housing.
(Figure B)
3

4
99-7318
FINAL ASSEMBLY
FINAL ASSEMBLY
1
Locate the factory wiring harness in the dash. Metra recommends using the
proper mating adapter and making connections as shown.
(Isolate and individually tape off the ends of any unused wires to prevent
electrical short circuit.)
2
Re-connect the negative batteryterminal and test the unit for proper operation.
3
Reassemble radio and dash assemblies in reverse order of disassembly.
A
A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
D) Tape
B
C
D
Make wiring connections using the EIA color code chart shown belowand the instructions included with the head
unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and individually
tape off ends of any unused wires to prevent electrical short circuit.
12V Ignition / Acc . . . Red
12V Batt / Memory . . Yellow
Ground . . . . . . . . . . . Black*
Power Antenna . . . . . Blue
Amp Turn-On . . . . . . Blue / White
Amp Ground . . . . . . . Black / White
Illumination. . . . . . . . Orange
Dimmer . . . . . . . . . . Orange / White
Right Front (+) . . . . . Gray
Right Front (-). . . . . . Gray / Black
Left Front (+) . . . . . . White
Left Front (-) . . . . . . . White / Black
Right Rear (+). . . . . . Violet
Right Rear (-) . . . . . . Violet / Black
Left Rear (+). . . . . . . Green
Left Rear (-) . . . . . . . Green / Black
*NOTE: When Black a wire is not present, ground radio to vehicle chassis.
All colors may not be present on all leads due to manufacturer’s specifications.
METRA / EIA WIRING CODE
FINAL WIRING CONNECTIONS

5
NOTES
99-7318
FINAL ASSEMBLY

99-7318 INSTRUCTIONS
1-800-221-0932 www.metraonline.com
REV. 08/24/07 © COPYRIGHT 2004-07 METRA ELECTRONICS CORPORATION INST99-7318