Mictrack MT600 User manual

MT600 User Manual V3.0
http://www.mictrack.com
MT600 4G GPS Tracker
User Manual V3.0
Preface
Congratulations on choosing the MT600 4G Vehicle GPS tracker. This manual shows
how to easily program and setup the tracker for best results. Make sure to read this
manual carefully before using this product, so as to avoid delays or confusion with it’s
operation. Please note that specifications and instructions are subject to change without
notice to facilitate product improvement. Updates and changes will be integrated into the
latest release. The manufacturer assumes no responsibility for any errors or omissions in
outdated documents.

MT600 User Manual V3.0
http://www.mictrack.com
Contents
1. Overview..................................................................................................................................... 1
2. Application...................................................................................................................................1
3. Specifications............................................................................................................................. 1
4. MT600 and Accessories..........................................................................................................3
5. Unit Diagram.............................................................................................................................. 3
6. Installation................................................................................................................................... 4
6.1 SIM Card installation.....................................................................................................4
6.2 LED Indications...............................................................................................................4
6.2.1 CHG-Charge indicator (RED).......................................................................... 4
6.2.2 SYS-System indicator (BLUE)......................................................................... 5
6.2.3 GPS-GPS indicator (GREEN)......................................................................... 5
6.3 Device Button Instruction............................................................................................. 5
6.4 Install 4G & GPS Antenna.......................................................................................... 5
6.5 Connection of supplied wiring loom.......................................................................... 6
6.6 Install the SOS switch (optional)............................................................................... 6
7. Setup and Configuration......................................................................................................... 6
7.1 Setting Authorized Mobile Phone Numbers.............................................................6
7.2 Deleting authorized number.........................................................................................7
7.3 Changing the Admin password...................................................................................7
7.4 Instant Location Request (used to receive unit location via SMS).................. 7
7.5 SOS Alarm (optional).................................................................................................... 7
7.6 Round Geo-fence (Setting of size and shape of Geo-Fence)...........................7
7.6.1 Enable the Round Geo-fence......................................................................... 7
7.6.2 Disable the Round Geo-fence........................................................................ 7
7.7 Square Geo-fence (Setting of dimensions and shape of Geo-Fence)............ 8
7.7.1 Enable the Square Geo-fence........................................................................ 8
7.7.2 Disable the Square Geo-fence....................................................................... 8
7.8 Remote cut off fuel and ignition (optional)............................................................. 8
7.9 External power cut off alarm...................................................................................... 8
7.10 Towing alarm................................................................................................................. 8
7.11 Low battery Alarm (internal backup battery)......................................................... 8
7.12 Low battery Alarm (Vehicle Battery)....................................................................... 8
7.13 High Temperature Alarm............................................................................................ 9
7.14 Over-Speed alarm (Alerts that the unit is exceeding a preset speed).........9
7.15 Set time zone............................................................................................................... 9
7.16 Set APN (Access Point Name)................................................................................ 9
7.17 Set Tracking Server IP and PORT......................................................................... 9
7.18 Set GPRS Upload Interval Time............................................................................. 9
7.18.1 ACC ON (Upload default status is AUTO)................................................9

MT600 User Manual V3.0
http://www.mictrack.com
7.18.2 Vehicle Towed Alarm (vehicle moves whilst ACC is turned OFF)... 10
7.18.3 ACC OFF & Vehicle Stationary (Upload status is AUTOLOW).........10
7.19 SMS Response ON/OFF......................................................................................... 10
7.20 Unit Phone Calling Control (useful for SIM Card data cost saving)...........10
7.21 Set GPRS mileage and trip distance reporting................................................. 11
7.21.1 Set upload interval distance........................................................................11
7.21.2 Clear the distance data................................................................................11
7.21.3 Check the current trip distance travelled.................................................11
8. App & PC Tracking platform............................................................................................... 11
8.1 Active the device ID number.................................................................................... 11
8.1.1 Contact with your sales or distributor.........................................................11
8.1.2 If not please subscribe the server plan from official online shop:..... 11
8.2 App install and login................................................................................................... 11
8.3 PC login......................................................................................................................... 12
9. Troubleshooting....................................................................................................................... 13

MT600 User Manual V3.0
http://www.mictrack.com
1
1. Overview
The MT600 is the latest technology 4G GPS tracker, fully supporting 4G LTE mobile
networks. This device can be used locate, track and monitor any remote target via SMS,
PC Computer or Mobile APP. It is commonly used to track and locate individual vehicles,
motorbikes or boats, and is a valuable tool for enhanced fleet management. The user also
can remotely cut off Fuel / Ignition and check the historical route travelled and other
vehicle data.
The MT600 has an excellent track record for stable performance and possesses a
wide variety of features.
2. Application
4G LTE network support (fallback to 3G/2G network)
Real-time tracking
Vehicle trip history and mileage data on web server
SOS alarm reporting (optional)
ACC switch status report
Geo-Fence alarm and reporting
External power cut off alarm
Remote cut off fuel / ignition (optional)
Vehicle towing / Movement alarm
Over-Speed alarm and reporting
Backup battery low power alarm
Car battery low power alarm
High temperature alarm
Power saving / sleep mode
3. Specifications
Item
Specifications
Dimension
90(L) x 70(W) x 24(H) mm
Weight
138g
Input Voltage
12-36 VDC
Backup battery
3.7 V 500 mAh
Power consumption
50mA standby current
Working temperature
-20°C to 60°C
Humidity
5%~95% non-concretion
Working Hours
10 hours in power-saving mode, 4 hours in normal mode

MT600 User Manual V3.0
http://www.mictrack.com
2
Item
Specifications
LED Indicator
4G(blue), GPS(green), Power(red)
Sensor
3D acceleration/movement sensor/ temperature sensor
Antennas
External 4G & GPS antennas
GPS Sensitivity
-162dBm
Positioning Accuracy
2.5m
4G Frequency bands
MT600-E (For Europe/Asia/Australia)
4G LTE: B1/B3/B5/B7/B8/B20
3G WCDMA : 850/900/2100MHz
2G: 900/1800MHz
MT600-A (for US/Canada)
4G LTE: B2/B4/B12
3G WCDMA: 850/1700/1900MHz
MT600-V (for Verizon)
4G LTE: B4/B13
MT600-AU (For Europe/Asia/Australia)
4G LTE: B1/B2/B3/B4/B5/B7/B8/B28/B40
3G WCDMA: 850/900/1900/2100MHz
2G :850/900/1800/1900MMz
MT600-AUT (for AU Telstra )
4G LTE: B1/B3/B5/B7/B28
3G WCDMA: 850/2100MHz
Note: Please select correct device according to your
local frequency band, or contact us for help.

MT600 User Manual V3.0
http://www.mictrack.com
3
4. MT600 and Accessories
Optional accessories:
5. Unit Diagram

MT600 User Manual V3.0
http://www.mictrack.com
4
6. Installation
6.1 SIM Card installation
1. Insert the SIM card into the SIM card plastic tray.
2. Ensure the SIM card has metal contacts facing up (Diagram #1).
3. Gently slide the SIM Tray into the SIM Slot (Diagram #2).
Note:
The device only supports Standard Size SIM card;
To remove SIM card, use paperclip to press the SIM card pop-out button to eject the
SIM card tray.
Diagram #1 Diagram #2
6.2 LED Indications
6.2.1 CHG-Charge indicator (RED)
Status
Description
Constant ON
Currently Charging
OFF
Charging Complete or sufficient battery.
(Note: it will auto-charging when backup battery voltage is
low and LED light, or LED will no light any more.)

MT600 User Manual V3.0
http://www.mictrack.com
5
6.2.2 SYS-System indicator (BLUE)
Status
Description
Constant ON
No SIM Card (or) No Network Reception
OFF
Vehicle Parked – ACC Power OFF
Quick flash
Normal Working Mode
6.2.3 GPS-GPS indicator (GREEN)
6.3 Device Button Instruction
Button
Description
Power
ON/OFF
Insert the SIM tray to POWER ON the unit; Take out SIM tray to
POWER OFF the unit
Connect the external power to POWER ON; Disconnect the
power to POWER OFF
6.4 Install 4G & GPS Antenna
Connect the 4G Antenna firmly to "3G/4G" Socket
Connect the GPS Antenna firmly to “GPS” socket
Status
Description
OFF
GPS / Satellites Unavailable – Out of Range
Quick flash
GPS/Satellite Locked – Normal Mode

MT600 User Manual V3.0
http://www.mictrack.com
6
6.5 Connection of supplied wiring loom
When installing the device, please connect supplied wiring loom as follows: (or
contact us for help)
Red: Connect to constant 12V Car Battery(+)
Black: Connect to Earth (Chassis) Car battery(-)
Green: Connect to ACC switched 12V Power
Yellow: Connect to red wire of supplied SOS switch
White: Connect to Relay terminal (85)
Pink: Connect to Relay terminal (86)
Note: Relay is optional for remote fuel / ignition shut-off.
6.6 Install the SOS switch (optional)
Red: connect to Yellow wire from supplied wiring loom
Black: connect to Earth (Chassis) Car battery(-)
Note: installation Video: http://youtube.com/c/mictrackgps
7. Setup and Configuration
Note: When sending SMS command to the unit, do NOT use spaces or symbols not
listed below. [brackets and + are for instructional use only] * and # are valid command
parameters.
7.1 Setting Authorized Mobile Phone Numbers
SMS Command format: mobile number+password+[command parameter]
Note: Command Parameter here is the sequence of the mobile number
i.e. [1=Admin] or [2=SOS call number]
For example: *13424392330*0000*1**
Unit Reply: SET USER NUMBER 1 OK.

MT600 User Manual V3.0
http://www.mictrack.com
7
Note:
The defaulted password is 0000.
It can authorize up to 3 phone numbers.
7.2 Deleting authorized number
SMS Command format: password+number+[command parameter]
Note: Command Parameter here is the sequence of the mobile number
i.e. [1=Admin] or [2=SOS call number]
For example: **0000*1**
Unit Reply: DELETE USER NUMBER 1 OK.
7.3 Changing the Admin password
SMS Command format: 777+new password+old password
For example: 77712340000
Unit Reply: SET USER PASSWORD OK.
7.4 Instant Location Request (used to receive unit location via SMS)
SMS Command format: 666+password
For example: 6660000
When sent, this command will result in a Unit Reply SMS as follows:
ID:865662000409210
Date:05:36:59 11/11/2016
Fix:A State:SMS
http://maps.google.com/maps?q=+22.63146%2c1+14.03701
Note: This link can to be opened on any Smart Phone to reveal the Google Maps
Location of the unit at the time of request
7.5 SOS Alarm (optional)
When the SOS button is pressed for 3 seconds, the unit will automatically send it’s
location to authorized phone number via SMS, and also upload location data to the Web
Tracking Platform server along with the status description “SOS”
7.6 Round Geo-fence (Setting of size and shape of Geo-Fence)
SMS Command format: 005+password+R+[Command Parameter]
Note: Command Parameter here is fence diameter in KM [0.1~999.9]
For example: 0050000R1.0
Unit Reply: SET ROUND GEO-FENCE:ON
7.6.1 Enable the Round Geo-fence
SMS Command format: 211+password
For example: 2110000
Unit Reply: SET ROUND GEO-FENCE: ON.
7.6.2 Disable the Round Geo-fence
SMS Command format: 210+password
For example: 2100000

MT600 User Manual V3.0
http://www.mictrack.com
8
Unit Reply: SET ROUND GEO-FENCE: OFF.
7.7 Square Geo-fence (Setting of dimensions and shape of Geo-Fence)
SMS Command format: 006+password+G1,IO/I/O,E/W longitude upper limit+N/S
latitude upper limit,E/W longitude lower limit+N/S latitude lower limit.
For example: 0060000G1,IO,E114.04540N22.59034,E114.05978N22.59797
Unit Reply: SET SQUARE GEO-FENCE1(IO)OK.
7.7.1 Enable the Square Geo-fence
SMS Command format: 311+password
For example: 3110000
Unit Reply: SET SQUARE GEO-FENCE: ON.
7.7.2 Disable the Square Geo-fence
SMS Command format: 310+password
For example: 3100000
Unit Reply: SET SQUARE GEO-FENCE: OFF.
7.8 Remote cut off fuel and ignition (optional)
To remotely Cut-Off fuel or power
SMS Command format: 940+password
For example: 9400000
Unit Reply: SET OILWAY DISCONNECT.
To remotely Resume fuel or power
SMS Command format: 941+password
For example: 9410000
Unit Reply: SET OILWAY RECOVERY CONNECT.
Note:The default setting for the Cut-Off feature is OFF
7.9 External power cut off alarm
If the external power to the unit is disconnected, [i.e. unit tampering or vehicle battery
removal] the unit will call the authorized phone numbers, and then send location data to
the authorized phone number and upload location data to the Web Tracking Platform
server along with the status description “DEF”
7.10 Towing alarm
If the vehicle was be moved or towed when ACC is turned OFF, it will SMS location
data to the authorized phone number, and upload location data to the Web Tracking
Platform server along with the status description “TOWED”
7.11 Low battery Alarm (internal backup battery)
When the unit’s internal backup battery is low, it will SMS the authorized phone
number, and upload location data to the Web Tracking Platform server along with the
status description “BLP”
7.12 Low battery Alarm (Vehicle Battery)
When the vehicle battery is low, it will SMS the authorized phone number, and upload

MT600 User Manual V3.0
http://www.mictrack.com
9
location data to the Web Tracking Platform server along with the status description “CLP”
7.13 High Temperature Alarm
When the devices internal temperature is high [preset value] it will SMS the
authorized phone number, and upload location data to the Web Tracking Platform server
along with the status description “HT”
7.14 Over-Speed alarm (Alerts that the unit is exceeding a preset speed)
SMS Command format: #122#user password#[Command Parameter]##
Note: Command Parameter here is [Km/Hour]
Example: #122#0000#100##
Unit Reply: SET SPEED LIMIT:ON
To disable the Over-Speed Alarm
SMS Command format: #122#0000#0##
Note: Command Parameter here is [0=OFF]
Unit Reply: SET SPEED LIMIT:OFF.
Note:Speed is in KM/H, Maximum setting = [999].
7.15 Set time zone
SMS Command format: 896+password+ [+/-]HH:MM
Note: Command Parameter here is [Plus or Minus GMT]&[Hours/Minutes]
For example: 8960000+10:00
Reply: SET TIME ZONE:+08:00
Note:The default is Greenwich Time (UTC). [i.e. Melbourne Australia = +10:00]
7.16 Set APN (Access Point Name)
SMS Command format 1: #803#password#APN##
For example : #803#0000#telstra.internet##
SMS Command format 2: #803#password#APN#APN user name#APN password##
For example: #803#0000#CMNET#INTERNET#INTERNET##
Reply: SET GPRS APN OK.
Note: Please CALL your SIM Card provider to get the correct APN info.
7.17 Set Tracking Server IP and PORT
SMS Command format: #804#password#IP address(or domain) #port##
Example:#804#0000#112.95.164.248#7700##
Reply: SET SERVER IP AND PORT OK.
7.18 Set GPRS Upload Interval Time
This sets how often [in seconds] the unit sends location data back to the Tracking
Platform whilst the ACC is switched on. This will affect accuracy and data usage.
7.18.1 ACC ON (Upload default status is AUTO)
SMS Command format: #805#password#interval time#[command parameter]##
Note: Command Parameter here [1=ON] & [0=OFF]
For example:#805#0000#10#1##

MT600 User Manual V3.0
http://www.mictrack.com
10
Unit Reply: SET GPS PERIODIC UPLOAD ON.
Note:interval time maximum [10,65535]seconds
Unit Reply: SET GPS PERIODIC UPLOAD OFF.
7.18.2 Vehicle Towed Alarm (vehicle moves whilst ACC is turned OFF)
SMS Command format: #809#password#interval time#[command parameter]##
Note: Command Parameter here [1=ON] & [0=OFF]
For example:#809#0000#10#1##
Unit Reply: SET GPS TOWED UPLOAD ON.
Note:interval time maximum [10,65535]seconds
Unit Reply: SET GPS TOWED UPLOAD OFF.
7.18.3 ACC OFF & Vehicle Stationary (Upload status is AUTOLOW)
[Periodic upload of vehicle status to the Web Tracking Platform server whilst ACC off
– variable to save SIM data costs when parked for long periods and Power Saving]
SMS Command format: #807#password#interval time##
For example: #807#0000#2##
Unit Reply: SET GPS POWER SAVING UPLOAD ON.
Note: interval time maximum [2,1440] minutes [If interval time = 0, it will stop upload]
Unit Reply: SET GPS POWER SAVING UPLOAD OFF.
7.19 SMS Response ON/OFF
To turn SMS messages OFF
SMS Command format: 160+password
For example: 1600000
Unit Reply: SET SEND SMS:OFF.
To turn SMS messages back ON
SMS Command format: 161+password
For example: 1610000
Unit Reply: SET SEND SMS:ON.
Note:if you want to disable the SMS alerts, send 1600000
7.20 Unit Phone Calling Control (useful for SIM Card data cost saving)
To turn OFF unit Calling Alerts
(i.e. to save SIM data costs)
SMS Command format: 150+password
For example: 1500000
Unit Reply: SET VOICE CALL:OFF
To turn ON unit Calling Alerts
SMS Command format: 151+password
For example: 1510000
Unit Reply: SET VOICE CALL: ON\
Note:if you want to disable the call alerts, send 1500000

MT600 User Manual V3.0
http://www.mictrack.com
11
7.21 Set GPRS mileage and trip distance reporting
This sets how often [in kilometres] the unit uploads data of “trip distance travelled”
back to the Tracking Platform whilst the ACC is switched on. This will affect
accuracy and data usage. This setting is often used for International Shipping
clients and Trucking Fleets to save data on long journeys.
7.21.1 Set upload interval distance
SMS Command format: #141#password#[command parameter]##
Note: Command Parameter here is [0=OFF] &[1000=1000 Kms]
Unit Reply: SET GPS MILEAGE STATISTICS:ON/OFF
7.21.2 Clear the distance data
SMS Command format: #142#password#[command parameter]##
Note: Command Parameter here is [0=clear current trip distance]
& [1=clear total distance travelled]
Unit Reply: SET GPS MILEAGE STATISTICS:CLEAR CURRENT/ALL
7.21.3 Check the current trip distance travelled
SMS Command format: #143#password##
For example: #143#0000##
Unit Reply: TOTAL GPS MILEAGE:X.X Km
CURRENT GPS MILEAGE:X.X Km
8. App & PC Tracking platform
8.1 Active the device ID number
8.1.1 Contact with your sales or distributor
8.1.2 If not please subscribe the server plan from official online shop:
https://www.mictrack.com/shop/gps-tracking-platform-service
And then leave the device’s ID number to active.
8.2 App install and login
Search “Yi tracker” in Google Play or iOS store to download the Mobile App(do
not select Yi tracker2)
Choose the”Login by Device No.”
Input server www.trackits.com
Input your device’s ID number and password(default is 123456, you can change
the password later)

MT600 User Manual V3.0
http://www.mictrack.com
12
8.3 PC login
Web: www.trackits.com
Choose “ID No.”
Input your device’s ID number and password(default is 123456)

MT600 User Manual V3.0
http://www.mictrack.com
13
9. Troubleshooting
Issues
Caused
Solutions
Send SMS to the
device but no reply
1>Data only SIM card and don't
supported SMS service,
2>New SIM card have not active
3>Card balance is not enough
Please check the SIM card
status and make sure it
can work.
Command is wrong
Please check the command
format again
Password is wrong
Please check the password
again (default is 0000)
4G antenna install wrong
Please check the 4G antenna
if install correct.
Can not get the location
GPS antenna install wrong
Please check again
Can not power on
Backup battery is low voltage
Please try to connect 12V
Charge Led no light
Backup battery voltage is over
3.7V.
The device will auto-charge
once detect to low voltage
and then LED light, or LED
will not night.
Device Can not online on
the server
Device ID is wrong
Please check the ID
Device have not active on server
Please contact your sales to
active your device’s ID
The IP and port setup wrong
Check the IP and port again
APN setup error
Check the APN setting again
Tips:
How to setup APN: https://www.mictrack.com/apn-settings-for-mictrack-gps-trackers
How to use Mictrack Server: https://www.mictrack.com/how-to-use-mictrack-server
Global Frequency bands check: https://www.mictrack.com/4g-lte-frequency-bands-list
Note: Please remember to monitor the credit balance of your SIM card, to
avoid confusion or delays in setting up your new unit. This can be a common issue,
especially when initially setting up a new unit, and the unit fails to reply to a correct
SMS command sequence.
If you have any questions please contact us [e-mail].