Midea NA64H3010AK User manual

1
Service Manual
For Built-in gas hob
GAS RANGES
Refer to the service manual in the Global Service Partner Network (GSPN).
See rear cover for more information

2
Contents
Table of contents
1. Precaution…………………………………………………3
2. Description of the appliance………………………………4
2.1 Features…………………………………………….4
2.2 Components and parts……………………………...7
3. Installation…………………………………………………8
4. Disassembly & Reassembly………………………………..10
5. Troubleshooting……………………………………………18
5.1Troubleshooting……………………………………...18
5.2Problems and Corrective Measures………………….19
6. Electric Diagram……………………………………………22
7. Gas Conversition……………………………………………23

3
1. Precaution
‘
Safty Precautions
1. Do not modify this appliance.
2. This appliance should be serviced by an authorized person.
3. All repairs should be done in accordance with the procedures described in
this manual.
4. Before you begin, turn off the gas and electricity supply to the appliance.
5. Remove remaining gas in product completely by igniting burner.
6. Be sure that all of built-in protective devices are replaced. Restore any
missing protective shields.
7. Use exact replacement parts only, i.e., only those that are specified in the
drawings and parts lists or this manual. Never alter or add to the
mechanical or electrical design of the appliance.
8. Do not connect the gas and electricity supply before replacement complete.
9. Use replacement components that have the same ratings. A replacement
part that does not have the same safety characteristics as the original
might create shock, fire or other hazards
10. You must conduct a gas leakage test after receiving after-sales service in
gas pipe and gas connector.
11. Never touch any circuit wiring with your hand nor with uninsulated tool
during operation.

4
2.Description of the appliance
2.1Features
NA64H3010AK NA64H3000AK
(60G40ME080-GFN-R05) (60G40ME080-GFN)
1.top plate
2.rapid burner
3.semi-rapid burner
4.auxiliary burner
5.control knob for lower left burner
6.control knob for upper left burner
7.control knob for upper right burner
8.control knob for lower right burner
9.pan support upper left (cast iron)
10.pan support lower left(cast iron)

5
2.Description of the appliance
2.1Features
Q 502 GFE
1．top plate
2．rapid burner
3．semi-rapid burner
4．auxiliary burner
5．control knob for lower left burner
6．control knob for upper left burner
7．control knob for middle burner
8．control knob for upper right burner
9．control knob for lower burner
10．pan support lower left
11．pan support lower right
12．pan support upper right
13．pan support middle
14．pan support upper left

6
2.Description of the appliance
2.1Features
Q411 SFD
1．top plate
2．control knob for left burner
3．control knob for upper burner
4．control knob for right burner
5．control knob for lower burner
6．auxiliary burner
7．Semi-rapid burner
8．rapid burner
9．Pan support right
10．pan support middle
11．pan support left

7
2.Description of the appliance
2.2 Components and parts

8
3.Installation
This appliance is to be built into a kitchen unit or 600mm worktop,providing the
following minimum distances are allowed;
–The edge of the appliance must be a minimum distance of 55mm from a rear
wall.
–A minimum distance of 150mm must be left between the side edges of the
appliance and any adjacent cabinets or walls.
–The minimum distance combustible material can be fitted above the
appliance in line with the edges of the appliance is 400mm. If it is fitted
below 400mm a space of 50mm must be allowed from the edges of the
appliance.
–The minimum distance combustible material can be fitted directly above the
appliance is 700mm.

9
3.Installation
–This panel (a) must be positioned at a maximum distance of 150mm below
the worktop.
Gas pipe or connector shouldn't be bent or blocked by any other appliances
–You must conduct a gas leakage test after installation over gas connection
and gas pipe.
–An oven must have forced ventilation to install a hob above it.
–Check the dimensions of the oven in the installation manual.
–The cut out size must obey the indication.

10
4.Disassembly and Reassembly