MiTAC PD10AI User manual

MITAC Desktop Board PD10AI
Product Guide

2
Desktop Board Features
This chapter briefly describes the features of Desktop Board PD10AI.
Below to summarizes the major features of the Desktop Board.
Feature Summary
T ABLE : M I TAC D ESKTOP B OARD PD10AI F EAT RES
Form Factor ow-profile Mini-ITX (20 millimeters [0.79 inches] x 170.18
millimeters [6.7 inches] x 170.18 millimeters [6.7 inches])
Processor Chipset
Intel Apollo ake Processor with integrated graphics (Compatible with
N3350 and N4200)
Main Memory
•Support for dual channel DDR3 1867 SO-DIMMs
•Support for up to 8 GB of system memory on a single SO-
DIMM (or
4 GB each by 2 SO-DIMM)
•204-pin DDR3 SO-DIMM 2
Audio Controller Realtek A C283 audio codec
Expansion
Capability
•PCI Express 2.0 x1 add-in card connector 1
•
M.2 (2242/2260/2280) with USB2.0 and SATA III signal
for SSD 1
•M.2 (2230) with PCIex1 and USB2.0 signal for wireless 1
External I/O
•DC-in Jack 1
•HD-out 1
•DP-out 1
•line-out 1
•Mic-in 1
•USB 3.0 back panel connectors 4
•RJ45 2
Internal I/O
•VDS 1
•eDP 1
•Stereo speaker header 1
•HD Audio/AC'97 headphone/mic 1
•USB 2.0 front panel ports 2
•SATA 3.0 Gb/s 1
•SATA 3.0 Gb/s port (multiplexed with an m.2 slot) 1
•Serial port header 2
•Parallel port header (Option with MiAPI header) 1
•4-pin system fan header 2
•2 pin power connector 1
S I/O Controller NCT6793D
AN Support Intel I211-AT (10/100/1000 Mb/s) Ethernet AN controller *2
BIOS •BIOS resident in a Serial Peripheral Interface (SPI) Flash device

3
•Support for Advanced Configuration and Power Interface (ACPI),
and System Management BIOS (SMBIOS)
Hardware
Management
Nuvoton NCT6793D based subsystem, including:
•Voltage sense to detect out of range power supply voltages
•Thermal sense to detect out of range thermal values
Environment •Operating Temperature: 0°C to +60°C
•Storage Temperature: -20°C to +70°C
Safety •CE
•FCC

4
Desktop Board Components
Figure shows the approximate location of the major components on the top side of
MiTAC Desktop Board PD10AI.
Figure: MiTAC Desktop Board PD10AI Components (Top)

5
T ABLE : M I TAC D ESKTOP B OARD PD10AI C OMPONENTS
A
Back
P
anel
C
onnectors
B
12V
2
-
PIN DC
-
in
C
M.2 Key
-
E
D
SATA 7
-
Pin Connector
E
Co 2 RS232 Power Select
F
SATA Power Connector
G
SO
-
DIMM
slot
H
CPU Fan Header
I
Syste Fan Header
J
Chassis Front I/O Header
K
LVDS Connector (eDP Connector at the botto side)
L
Panel Power
M
LCD Panel Power Select
N
Inverter Power Select
O
USB 2.0 Header
P
M.2 Key
-
M
Q
Parallel port/ MiAPI Header
R
CMOS Reset
S
Legacy I/O Header
T
COM1 RS232
U
COM1 RS232 Power Select
V
COM2 RS232
W
AT/ATX Mode
X
MCU Progra Header
Y
PCI Express X1
Connector
Z
Speaker Header
AA
Front Panel Audio Header

6
Processor
MITAC Desktop Board PD10AI includes a passively-cooled, Intel Apollo ake N3350/N4200
processor with integrated graphics and memory controller. The processor is soldered
to the Desktop Board and is not customer upgradeable.
NOTE
The board is designed to be passively cooled in a properly ventilated chassis. Chassis
venting locations are recommended above the processor heatsink area for maximum
heat dissipation effectiveness.
System Memory
NOTE
To be fully compliant with all applicable SDRAM memory specifications the
board should be populated with DIMMs that support the Serial Presence Detect (SPD)
data structure. If your memory modules do not support SPD you will see a
notification to this effect on the screen at power up. The BIOS will attempt to
configure the memory controller for normal operation.
The Desktop Board has two 204-pin DDR3 SO-DIMM sockets with gold-plated contacts.
These sockets support:
Support for DDR3 SO-DIMMs
Serial Presence Detect (SPD) memory only
Non-ECC memory
Up to 8 GB of memory (on a single SO-DIMM or 4 GB each by 2 SO-DIMM)