MiTAC TYAN S5502 User manual

1
http://www.tyan.com
S5502
Version 1.0
Copyright
Copyright © 2009 MiTAC International Corporation. All rights reserved. No part of
this manual may be reproduced or translated without prior written consent from
MiTAC International Corporation.
Trademark
All registered and unregistered trademarks and company names contained in this
manual are property of their respective owners including, but not limited to the
following.
TYAN®is a trademark of MiTAC International Corporation.
Intel®is a trademark of Intel®Corporation.
AMI, AMI BIOS are trademarks of AMI Technologies.
Microsoft®, Windows®are trademarks of Microsoft Corporation.
Winbond®is a trademark of Winbond Electronics Corporation.
Notice
Information contained in this document is furnished by MiTAC International
Corporation and has been reviewed for accuracy and reliability prior to printing.
MiTAC assumes no liability whatsoever, and disclaims any express or implied
warranty, relating to sale and/or use of TYAN®products including liability or
warranties relating to fitness for a particular purpose or merchantability. MiTAC
retains the right to make changes to product descriptions and/or specifications at
any time, without notice. In no event will MiTAC be held liable for any direct or
indirect, incidental or consequential damage, loss of use, loss of data or other
malady resulting from errors or inaccuracies of information contained in this
document.

http://www.tyan.com
2

http://www.tyan.com
3
Contents
Before you begin…....................................................................................5
Chapter 1: Instruction ................................................................................7
1.1 Congratulations .................................................................................7
1.2 Hardware Specifications....................................................................7
1.3 Software Specifications.....................................................................9
Chapter 2: Board Installation...................................................................11
2.1 Board Image....................................................................................12
2.2 Block Diagram.................................................................................13
2.3 Board Parts, Jumpers and Connectors...........................................14
2.4 Installing the Processor...................................................................24
2.5 Heat sink Installation .......................................................................26
Finishing Installing the Heat sink.............................................................26
2.6 Thermal Interface Material ..............................................................27
2.7 Tips on Installing Motherboard in Chassis ......................................28
2.8 Installing the Memory ......................................................................30
2.9 Attaching Drive Cables....................................................................33
2.10 Installing Add-In Cards..................................................................34
2.11 Connecting External Devices ........................................................35
2.12 Installing the Power Supply...........................................................36
2.13 Finishing Up...................................................................................38
Chapter 3: BIOS Setup .............................................................................39
3.1 About the BIOS................................................................................39
3.2 BIOS Main Menu.............................................................................41
3.3 BIOS Advanced Menu.....................................................................42
3.4 PCI/PnP...........................................................................................54
3.5 Boot .................................................................................................55
3.6 Security............................................................................................58
3.7 Chipset ............................................................................................59
3.8 Exit...................................................................................................63
Chapter 4: Diagnostics.............................................................................65
4.1 Beep Codes.....................................................................................65
4.2 Flash Utility......................................................................................65
4.3 AMIBIOS Post Code........................................................................66
Appendix: How to Make a Driver Diskette..............................................69

http://www.tyan.com
4
Glossary.....................................................................................................71
Technical Support ....................................................................................77

http://www.tyan.com
5
Before you begin…
Check the box contents!
The retail motherboard package should contain the following:
1x S5502 Motherboard
1 x SAS cable (S5502WGM3NR only)
6 x Serial ATA Cable
1 x USB2.0 cable
1 x S5502 User’s manual
1 x S5502 Quick reference guide
1 x TYAN®Driver CD
1 x I/O shield

http://www.tyan.com
6
NOTE

http://www.tyan.com
7
Chapter 1: Instruction
1.1 Congratulations
You have purchased one of the most powerful TYAN® S5502 motherboard.
Based on Intel®3420 chipsets, the TYAN S5502 single-socket server platform
offers a compact design and superior performance at a lower cost compared to
previous generation products.
The TYAN S5502 offers the full functionality that is required in a standard UP server
platform. The S5502 supports (1) Intel Xeon processor 3400 series, (6) DDR-III
DIMM slots, and (2) GbE ports in an ATX form factor. This design can be easily
installed into a standard pedestal chassis for most entry level applications in
Workgroups, SMB and Education environments.
The S5502 not only empowers you in today’s demanding IT environment but also
offers a smooth path for future application usage. All of this provides S5502 the
power and flexibility to meet the needs of nowadays application.
Remember to visit TYAN®’s Website at http://www.tyan.com. There you can find
information on all of TYAN®’s products with FAQs, online manuals and BIOS
upgrades.
1.2 Hardware Specifications
Supported CPU
Series Intel®Xeon®processors 3400 series
Socket Type / Q'ty LGA1156 / (1)
Processor Thermal Design
Power (TDP) wattage 95W/ 82W/ 45W
PCH / PCI-E Switch Intel®3420 / IDT 89HIO524G2PS
Chipset Super I/O Winbond W83627DHG
Supported DIMM Qty (6) DIMM sockets
DIMM Type / Speed DDR3 800/1066/1333 RDIMM/UDIMM
Capacity Up to 32GB RDIMM / 16GB UDIMM
Memory channel 2 Channels
Memory
Memory voltage 1.5V
PCI-E
(1) PCI-E Gen.2 x16 slot (w/ x8 link)
(1) PCI-E Gen.2 x8 slot (w/ x8 link)
(1) PCI-E Gen.2 x8 slot (w/x4 link)
(1) PCI-E x8 slot (w/ x4 link)
Recommended
TYAN®Riser Card M2083-RS, PCI-E x16 1U riser card (left)
M2091, PCI-E x16 1U riser card (left)
Expansion
Slots
PCI
(1) PCI 32/33MHz slot

http://www.tyan.com
8
Port Q'ty (3)
LAN Controller Intel®82574L
Connector (4)
Controller Marvell 88SE6440 (S5502WGM3NR only)
Speed 3.0 Gb/s
SAS
(opt.)
RAID RAID 0/1/1E (Marvell Integrated RAID)
Connector (3) 2-port
Controller Intel® 3420
Speed 3.0 Gb/s
Storage
SATA
RAID RAID 0/1/10/5 (Intel®RST)
Connector type D-Sub 15-pin
Resolution 1600x1200@60Hz Graphic
Chipset Aspeed AST2050
USB (10) USB2.0 ports (4 at rear, 4 via cable, 2 type A onboard)
COM (2) ports (1 at rear, 1 via cable)
PS/2 (1) PS/2 connector
SAS
(opt.) (4) SAS connectors
(S5502WGM3NR only)
VGA (1) D-Sub 15-pin VGA port
RJ-45 (3) GbE ports
Power SSI 24-pin + 8-pin + 8-pin power connectors / EPS12V
Front Panel (1) 2x12 pin SSI front panel header
Input /Output
SATA (3) stacked 2-port SATA-II connectors
Chipset Winbond W83793G
Voltage Monitors voltage for CPU, memory, chipset & power supply
Fan Total (5) 4-pin headers
Total (5) 8-pin headers (for Barebone)
Temperature Monitors temperature for CPU & system environment
System
Monitoring
Others Chassis intrusion detection
Watchdog timer support
Onboard Chipset Onboard Aspeed AST2050
AST2050 IPMI
Feature
IPMI 2.0 compliant baseboard management controller (BMC)
BIOS update
USB 2.0 virtual hub
Server
Management
AST2050 iKVM
Feature 24-bit high quality video compression
Dual 10/100 Mb/s MAC interfaces
BIOS Brand / ROM size AMI / 4MB

http://www.tyan.com
9
Feature
Plug and Play (PnP)/ PCI 2.3
WfM2.0 / SMBIOS2.3 / PXE boot
ACPI 2.0 power management
Power on mode after power recovery
User-configurable H/W monitoring
Auto-configurable of hard disk types
Multiple boot options
Form Factor ATX
Form Factor Board Dimension 12"x9.6" (305x244mm)
Operating
System OS supported list Please refer to our OS supported list.
FCC (DoC) Class B
Regulation CE (DoC) Yes
Operating Temp. 5° C ~ 35° C (41° F~ 95° F)
Non-operating Temp. - 40° C ~ 70° C (-40° F ~ 158° F)Operating
Environment In/Non-operating
Humidity 90%, non-condensing at 35° C
RoHS RoHS 6/6 Complaint Yes
1.3 Software Specifications
For OS (operation system) support, please check with TYAN®support for latest
information.

http://www.tyan.com
10
NOTE

http://www.tyan.com
11
Chapter 2: Board Installation
You are now ready to install your motherboard.
How to install our products right… the first time
The first thing you should do is reading this user’s manual. It contains important
information that will make configuration and setup much easier. Here are some
precautions you should take when installing your motherboard:
(1) Ground yourself properly before removing your motherboard from the
antistatic bag. Unplug the power from your computer power supply and
then touch a safely grounded object to release static charge (i.e. power
supply case). For the safest conditions, MiTAC recommends wearing a
static safety wrist strap.
(2) Hold the motherboard by its edges and do not touch the bottom of the
board, or flex the board in any way.
(3) Avoid touching the motherboard components, IC chips, connectors,
memory modules, and leads.
(4) Place the motherboard on a grounded antistatic surface or on the antistatic
bag that the board was shipped in.
(5) Inspect the board for damage.
The following pages include details on how to install your motherboard into your
chassis, as well as installing the processor, memory, disk drives and cables.
NOTE Do not apply power to the board if it has been damaged.

http://www.tyan.com
12
2.1 Board Image
This picture is representative of the latest board revision available at the time of
publishing. The board you receive may not look exactly like the above picture.

http://www.tyan.com
13
2.2 Block Diagram

http://www.tyan.com
14
2.3 Board Parts, Jumpers and Connectors
This diagram is representative of the latest board revision available at the time of
publishing. The board you receive may not look exactly like the above diagram. But
for the DIMM number please refer to the above placement for memory
installation. For the latest board revision, please visit our web site at
www.tyan.com.

http://www.tyan.com
15
Jumpers & Connectors
Jumper/Connector Function
J8/J9/J30/J32/J33 4-pin Fan connector
J37/J38/J39/J40/J42 8-pin 4096 fan header
J19/J20 USB Front Panel Header
USB3/USB4 Type-A USB Connectors
J22 TYFP1 Header
J15 COM2 Header
JP4 Clear CMOS Jumper
J41 Chassis Intrusion Jumper
JP1/JP2 COM switch
J2 IPMB Connector
J6 Enable/Disable BMC jumper
J25 PSMI Connector
JP5 Speaker Header
J16 Port80 Header
J21 LAN3 LED Header
J23 SAS GPIO to Backplane
J36 PCH SGPIO
J35 2X10_pin FAN connector
J7 LCM Header
Jumper Legend
OPEN - Jumper OFF Without jumper cover
CLOSED - Jumper ON With jumper cover

http://www.tyan.com
16
CPUFAN0
Rear Fan2
J40
FrontFAN1
Rear Fan1
FrontFAN2
J39
J38
J37
J42
J19 J20

http://www.tyan.com
17
J8/J9/J30/J32/J33: 4-Pin FAN Connector
Pin_1
J32: CPUFAN0
J9: RearFAN1
J8: RearFAN2
J33: FrontFAN1
J30: Front FAN2
Use these headers to connect the cooling fans to the
motherboard to keep the system stable and reliable.
Pin 1 Pin 2 Pin 3 Pin 4
GND +12V Tachometer Fan PWM (speed)
Control
J37/J38/J39/J40/J42: 8-Pin 4096 fan header
These headers are reserved for Barebone
Pin Signal Pin Signal
1 PWM1 2 +12V
3 TACH1 4 GND
5 GND 6 TACH2
7 +12V 8 PWM2
J19/J20: USB Front Panel Header
Signal Pin Pin Signal
PWR_5V 1 2 PWR-5V
USB_N1 3 4 USB_N2
USB_P1 5 6 USB_P2
GND 7 8 GND
KEY 9 10 N/C
USB3/USB4: Type-A USB Connector
Pin 1 2 3 4
Signal +5V USB D- USB D+ GND

http://www.tyan.com
18
J15 J22
J41
JP4

http://www.tyan.com
19
J22: TYFP1 Header
Signal Pin Pin Signal
Power LED+ 1 2 3.3V
Key 3 4 ID LED+
Power LED- 5 6 ID LED-
HD LED+ 7 8 Fault_LED1-
HD LED- 9 10 Fault_LED2-
Power SW# 11 12 LAN1 ACTLED+
GND1 13 14 LAN1 ACTLED-
Reset SW# 15 16 SMBUS SDA
GND2 17 18 SMBUS SCL
ID SW 19 20 INTRU#
Temp Sensor 21 22 LAN2 ACTLED+
NMI_SW# 23 24 LAN2 ACTLED-
J15: COM2 Connector
Signal Pin Pin Signal
DCD 1 2 DSR
RXD 3 4 RTS
TXD 5 6 CTS
DTR 7 8 RI
GND 9 10 KEY
JP4: Clear CMOS Jumper
1
Normal (Default)
1
Clear CMOS
Use this jumper when you forgot your system/setup
password or need to clear system BIOS setting.
How to clear the CMOS data
-Power off system and disconnect power
supply from AC source
-Use jumper cap to close Pin_2 and 3 for
several seconds to Clear CMOS
-Replace jumper cap to close Pin_1 and 2
Reconnect power supply to AC source
Power on system
J41: Chassis Intrusion Jumper
1
Use this jumper to disable the system chassis
intrusion alarm.
(Default) Use this jumper to trigger the system chassis
intrusion alarm.

http://www.tyan.com
20
J6
J2
JP1
JP2
J25
JP5
J16