MiTAC ND108T User manual

MiTAC
ND108T
Quick Installation Guide
2020/7/30
V01

2
MB Placement
1 x UART header
for debugging
1 x USB 2.0 OTG
port Header for
programming
1 x Line-
out/Mic-in
1 x USB2.0
ports header
1 x Power
Switch
12V internal 4-
pin DC-in
connector
1 x Raspberry Pi 40-pin header
J22
J19
J13
J1
J3

3
Pin Definition (1/3)
(J1)
J1 J19

4
Pin Definition (2/3)
(J22)
(J13)
J13 J22

5
Pin Definition (3/3)
J3 Raspberry Pi 40-pin header

6
How to insert the Micro SD card

7
How to enter U-boot
The bring up sequences will count-down 3 seconds in u-boot.
Please use RS232 to connect ND108T’s J22 (UART_TX and UART_RX), and press any key in 3 seconds to enter u-boot.

THIS DOCUMENT IS PROPERTY OF MiTAC COMPUTING TECHNOLOGY CORPORATION. ITS USE IS
AUTHORIZED ONLY FOR RESPONDING TO A REQUEST OR FOR QUOTATION OR FOR THE
PERFORMANCE OF WORK FOR MITAC COMPUTING TECHNOLOGY CORP. ALL QUESTIONS MUST
BE REFERRED TO THE MITAC COMPUTING TECHNOLOGY CORP..
2020/06/29
ND108T Yocto & Android Image Update Standard Operation Procedure
Title: ND108T Yocto & Android Image Update Standard Operation Procedure
Project: ND108T
Revision: 1.1
Author:
Revision Date: 2020/06/29
Rev.
Date
Name
Comment
1.0
2020/04/22
Mark Chang
Draft (skeleton)
1.1
2020/06/29
Mark Chang
Add Android image support
Copyright Notice
Copyright © 2017 by MiTAC Computing Technology Corporation
All Rights Reserved. Printed in Taiwan.
This publication is protected by copyright and all rights are reserved. No part or whole of it may be reproduced or
transmitted in any form or by any means, electronic or mechanical, including photocopying and recording without prior
consent of MiTAC Computing Technology Corporation.
The information in this document has been carefully checked and is believed to be accurate. However, MiTAC
Computing Technology Corporation assumes no responsibility for any errors that may appear in this document. The material
contained herein is for informational purposes only. The information contained in this document is subject to change without
any notices.

THIS DOCUMENT IS PROPERTY OF MiTAC COMPUTING TECHNOLOGY CORPORATION. ITS USE IS
AUTHORIZED ONLY FOR RESPONDING TO A REQUEST OR FOR QUOTATION OR FOR THE
PERFORMANCE OF WORK FOR MITAC COMPUTING TECHNOLOGY CORP. ALL QUESTIONS MUST
BE REFERRED TO THE MITAC COMPUTING TECHNOLOGY CORP..
Table of Contents
Table of Contents ............................................................................................. 2
1Purpose ...................................................................................................... 3
2Yocto Image Update ................................................................................... 3
3Android Image Update ............................................................................... 7

Project: ND108T
ND108T Yocto & Android Image Update SOP
MiTAC Computing Technology Corp. Proprietary and Confidential PAGE 3OF 10
November 01, 2017
1Purpose
This Standard Operation Procedure (SOP) describes the usage of Yocto & Android
image update method for ND108T project.
2Yocto Image Update
1) Configure DIP switches SW1 [1 2] to [OFF ON] and SW2 [1 2 3 4] to [OFF OFF ON OFF].
SW1 (Boot Mode DIP)
DIP1
DIP2
Boot Source
OFF
ON
Serial Download Mode
ON
OFF
Internal Boot Mode
SW2 (Boot Media DIP)
DIP1
DIP2
DIP3
DIP4
Boot Media Configuration
OFF
OFF
ON
OFF
eMMC
ON
ON
OFF
OFF
microSD