Mitel Superset 4150 User manual

User Guide

Notice
The information contained in this document is believed to be accurate in all respects but is not warranted by Mitel Networks#x00ae;
Corporation. The information is subject to change without notice and should not be construed in any way as a commitment by Mitel
Networks or any of its affiliates or subsidiaries. MITEL® and its affiliates and subsidiaries assume no responsibility for any errors or
omissions in this document. Revisions of this document or new editions of it may be issued to incorporate any such changes.
Nothing in this document may be reproduced in any manner, either wholly or in part for any use whatsoever, without written
permission from MITEL® Networks Corporation.
SUPERSET™ Copyright© 2001, Mitel Networks Corporation. All rights reserved. Printed in Canada.
IMPORTANT! This telephone is NOT suitable for direct connection to the public-switched telephone network. Connect the telephone
to a Mitel telephone system only.

-i-
Contents
ABOUT YOUR PHONE 1
TIPS FOR YOUR COMFORT AND SAFETY 2
Don't cradle the handset! 2
Protect your hearing 2
Adjusting the viewing angle 2
Changing Handsets 3
CUSTOMIZING YOUR PHONE 4
Ringer Control 4
Handset Receiver Volume Control 4
Speaker Volume Control 4
Display Contrast Control 4
Feature Keys 5
Language Change 5
Clean Mode 5
MAKING AND ANSWERING CALLS 6
Make a call 6
Answer a call 6
Phonebook 6
Redial 7
Redial - Saved Number 7
Speed Call Keys 8
Speed Call - Personal 9
Handsfree Operation 10
Auto-Answer 11

-ii-
CALL HANDLING 12
Hold 12
Transfer 12
Conference 12
Conference Split 13
Add Held 13
Swap 13
Call Forward 14
Call Forward - I Am Here 15
Call Forward - End Chaining 16
Call Forward - Forced 16
Call Forward - Override 16
Messaging - Advisory 16
Messaging - Callback 17
USING ADVANCED FEATURES 19
Account Codes 19
Callback 19
Call Park 20
Call Pickup 20
Campon 20
Do Not Disturb 21
Override 21
Paging 21
Direct Paging 22
Reminder 23
Headset Operation 23
Headset Operation (with Feature Control Switch) 24
Music 24
Calculator 25
Group Paging / Meet Me Answer 25
Trunk Flash 26
USING MLPP 26

-iii-
FEATURE ACCESS CODES 29

-1-
ABOUT YOUR PHONE
The SUPERSET 4150 has six fixed-function keys ( HOLD, SUPERKEY,
SPEAKER, MICROPHONE, , ) and 14 personal keys with built-in status
indicators. The personal key on the bottom right is always your Prime Line;
the remaining personal keys can be programmed as Feature, Speed Call, or
Line Appearance keys. See Feature Keys for personal key programming
instructions.
Personal Keys can be programmed as feature keys (such as Swap key) by
you or by your Administrator.
Your telephone also features a touch-sensitive display for softkey feature
access, Handsfree operation, and a large Message Indicator.
Note: When using the Superkey, press the Backup softkey to back up one
menu level.
Your SUPERSET 4150 may be connected to a PC. See your system
administrator for computer-telephony features that may be available to you
if your telephone has been connected in this way.
IMPORTANT NOTE FOR HEADSET USERS:
Mitel Networks Headsets with Feature Control Switch (PN9132-800-500-
NA/9132-800-501-NA) must be installed in the dedicated headset jack (the
j
ack nearest the front of the set). Installation will disable your handset
microphone. Disconnecting the headset at the jack or at the quick-
disconnect plug restores handset operation.
Telephone status indicators
When line is the indicator is
Idle Off
Busy On
Ringing Flashing slowly
On hold at your set Flashing rapidly
On hold at another set Flashing slow on/fast off

-2-
TIPS FOR YOUR COMFORT AND SAFETY
Don't cradle the handset!
Prolon
g
ed use of the handset can lead to neck, shoulder, or back discomfort,
especially if you cradle the handset between your ear and shoulder. If you
use your phone a lot, you may find it more comfortable to use a headset.
See the section on headset usage elsewhere in this guide for more
information.
Protect your hearing
Your phone has a control for ad
j
ustin
g
the volume of the handset receiver or
headset. Because continuous exposure to loud sounds can contribute to
hearing loss, keep the volume at a moderate level.
Adjusting the viewing angle
The stand built into your phone tilts to give you a better view of the keys.
To tilt your telephone for better viewing:
1. Press the tilt-release paddle on the telephone base.
2. Tilt your telephone to the desired angle.
3. Release the tilt-release paddle.

-3-
Changing Handsets
Your SUPERSET 4150 telephone is compatible with several specialty
handsets. To remove the handset shipped with your set from the handset
cord:
1. Bend a paper clip to produce approximately 4 cm (1.5 in.) of straight
wire.
2. On the handset, locate the plastic groove leading into the handset jack.
The groove is on the side of the jack that is closest to the handset
microphone.
3. Slide the end of the wire into the handset jack along the groove until it
stops underneath the handset cord clip.
4. While gently pulling on the handset cord, use the wire to pry the clip
upward. The cord will separate from the handset.
5. Store the original handset in a safe place.

-4-
CUSTOMIZING YOUR PHONE
Ringer Control
To adjust the Ringer Volume while the set is ringing:
zPress or .
To adjust the Ringer Pitch while the set is idle:
1. Press SUPERKEY.
2. Press the More softkey until the Ring Adjust softkey appears.
3. Press the Ring Adjust softkey.
4. Press the Ringer Pitch softkey.
5. Press or .
6. Press SUPERKEY.
Handset Receiver Volume Control
To adjust the Handset Receiver Volume when you are using the
handset:
zPress or .
Speaker Volume Control
To adjust the Speaker Volume when making an on-hook call or when
listening to background music:
zPress or .
Display Contrast Control
To adjust the Display Contrast while your set is idle:
zPress or .

-5-
Feature Keys
To display information about a key:
1. Press SUPERKEY.
2. Press a personal key.
3. Press SUPERKEY.
To re-program a personal key:
1. Press SUPERKEY.
2. Press the More softkey until the Display Keys softkey appears.
3. Press the Display Keys softkey.
4. Press a personal key that isn't a line key.
5. Do one of the following:
To change the key, press the Change Key softkey, and select a new
key type.
To clear the key, press the Clear Key softkey.
6. Press SUPERKEY.
Language Change
To change the display language:
1. Press SUPERKEY.
2. Press the More softkey until the Language softkey appears.
3. Press the Language softkey.
4. Press the softkey for the desired language.
Clean Mode
To disable the touch-sensitive display so that it can be cleaned (use a
dry tissue):
1. Press SUPERKEY.
2. Press the More softkey until the Clean LCD softkey appears.
3. Press the Clean LCD softkey.
4. Clean the surface of the display.
5. Press SUPERKEY.