Mobi Technologies 70117 User manual

Air Non-Contact
Forehead Thermometer
Item No: 70117
Instruction Manual
Please read this instruction manual completely before operating.
Package Contents
Quantity
1pc
2pc
1pc
Parts
Air Non-Contact Forehead Thermometer
1.5V (AAA) Batteries
User Manual
Product Specification
1. Distance Sensor
2. Infrared Sensor
3. LCD Display
4. Power/Scan Button
5. MEM - Memory Button
6. Temperature Mode Selection
7. Battery Cover
1. Forehead Temperature Symbol
2. Ambient Temperature Symbol
3. Object Temperature Symbol
4. Low Battery Symbol
5. Temperature Display
6. C°/F° Symbol
7. Memory Mode Symbol

Installing / Replacing Battery
•Located at the back lower base of the thermometer is the battery cover.
•Insert two AAA batteries to match the “+” and “- “as illustrated in the battery compartment.
•Make sure no plastic tabs are in between the batteries and the springs.
•Close the battery cover and ensure it is locked in place before operation.
•Replace battery when low battery indicator appears.
•When replacing batteries, always replace with new AAA batteries ensuring to again match polarities
indicated in the battery compartment.
oIf the thermometer does not power on after replacing the batteries, please remove the
batteries and allow 60 seconds to pass before reinstalling the batteries once more.
Note: Please follow local and state guidelines for proper battery disposal.
Turning the Unit On/Off
•To turn on the unit, simply press and release the ‘Power/Scan’button.
•For conservation of battery, this unit will automatically power off, after inactivity. There is no manual
off button.
Celsius and Fahrenheit Settings
•Press the power button to turn the thermometer on.
•In the bottom right corner, you will see either ‘F’ or ‘C’. This is the unit the thermometer is currently
recording measurements.
•To change the unit of measurement please press and hold the “MEM/SET” button to switch to the
alternative unit. The newly selected unit will be displayed on the screen.
Adjusting Sound: On/Off
•To turn the sound on/off long press the ‘MODE’ button.
•If sound is being turned ‘ON’ device will ‘beep’ twice and display the word “ON”.
•If sound is being turned ‘OFF’ device will ‘beep’ once and display the word “OFF”.
Memory Function
•Each temperature taken by this unit is stored in the memory.
•This unit has the capability to hold 20 readings in the memory.
•To access the memory data please press and release the ‘MEM’button.
•The latest reading will be displayed. The Memory number will be displayed on the screen.
•Continue to press (and release) the ‘MEM’ button to filter through the stored information.
•Once the memory is full the oldest data will automatically be deleted and overwritten with the new
information.

Temperature Indicators
•This thermometer has a fever indication light.
•A Green LED will light up around the Power/Scan button if the temperature is between
93.2°F(34.0°C) ~ 100.3°F(37.9°C).
•A Red LED will light up around the Power/Scan button if the temperature is between
100.4°F(38.0°C) ~ 109.4°F(43.0°C)
Note: If thermometer is placed too far away to take temperature the LED will light up BLUE and beep until
in the proper position.
Measurement Preparation for Best Results
•For more accurate measurements always store the device in same environment it is being used, for
at least 30 minutes prior. An unexpected fluctuation of ambient temperature is likely to lower
measuring accuracy.
•Do not talk or move body during measurement.
•Make sure to dry forehead & clear any excessive hair which may cause inaccurate reading.
•The infrared sensor must be kept clean, dry, and undamaged to ensure accurate results.
•External factors may influence forehead temperatures, particularly when the individual has been:
oExposed to very hot or cold temperatures.
oRecently exercised, bathed, or other physical exertion as this increase’s temperature.
•Ensure the thermometer is correctly placed before taking the reading. Reference the sections below
for how to best position the thermometers for each reading method.
•Use of this device is not intended as a substitution for consultation with your physician.
Measurement results are for reference only. Contact your physician if you have or suspect and
health concerns.
Forehead Temperature
Forehead results will display from 89.6 ° F to 109.2 ° F (32.0 ° C to 42.9 ° C). ‘HI’is displayed for all results
above 109.2 ° F (42.9 ° C), and ‘LO’is displayed for result below 89.6 ° F (32.0 ° C).
•Ensure the unit is in ‘forehead mode’. In the upper left-hand corner, there will be an icon of a head.
If you do not see the head icon in the upper left-hand corner, press and release the ‘MODE’ button
to switch mode until the correct icon displays on screen.
•For optimal results point the unit towards the forehead holding the probe 0.4 - 2 inches away from
the forehead.
•Ensure you point the unit first, then press and release the ‘ON/Scan’ button. Scanning before
correctly positioning the thermometer will result in inaccurate readings.
•Allow 1-2 seconds after pressing the ‘ON/Scan’ button for temperature to display (if the sound is on
the thermometer will ‘beep’).
•Please remove any obstructions like hats, beanies, headbands, and hair for accurate reading.
•Please remember to take temperature in a controlled environment where direct sunlight or cold air
will not affect the measurement.
•Please wait a few minutes before taking the temperature of an individual who has been exposed to
extreme heat or sever cold weather.

Object / Food Temperature
•Ensure the unit is in ‘Object mode’. In the upper right-hand corner, there will be an icon of a bottle.
If you do not see the bottle icon in the upper right hand corner press and release the ‘MODE’ button
to switch modes until the correct icon displays on screen.
•For optimal results point the unit towards the ‘object’ holding the probe 0.4 - 2 inches away from the
object.
•Ensure you point the unit first, and then press and release the ‘ON/Scan’ button. Scanning before
correctly positioning the thermometer will result in inaccurate readings.
•Allow 1-2 seconds after pressing the ‘ON/Scan’ button for temperature to display (if the sound is on
thermometer will ‘beep’ once)
Room Temperature
•When the thermometer is turned on, it will display the ambient room temperature. In the upper
middle section, there will be an icon of a house.
Troubleshooting
•Resetting the Thermometer
To reset your thermometer, take out the batteries for 1 hour while storing the unit in a warm place with
sunlight. Make sure the sensor of the thermometer isn’t in direct contact with the sunlight, only the body of
the thermometer. After the 1 hour, insert the batteries and turn on the device.
•ErrE
If you receive and ‘ErrE’ message on the screen, place the thermometer in sunlight or a warm place and let
sit for 30 minutes.
•HI
‘HI’is displayed for all results above 109.2 °F (42.9°C). Please ensure that you are in correct reading method.
•LO
‘LO’is displayed for result below 89.6 °F (32.0°C). Please ensure that you are in correct reading method.
Care and Maintenance
•It is recommended that the thermometer is stored in a dry place free from dust.
•Do not expose sensor to direct sunlight or air conditioning/fan that will tamper with the
thermometer sensor.
•Please do NOT expose thermometer to any humidity or water (non-waterproof).
•To clean the unit, please use an alcohol swab or wipe. Do not use water directly. Ensure all residual
alcohol has evaporated before use.

Thermometer Specification
Measurement Unit:
Body Temperature Measuring Range:
Laboratory Accuracy:
Object Temperature Measure Reading:
Object Temperature Measuring Accuracy:
Dimension:
Weight:
Forehead Operating Condition:
Object Operating Condition:
Storage and Transport Condition:
Service Life of the Battery:
IP Classification system:
Classification of ME Equipment:
°C/°F
32.0°C ~ 42.9°C (89.6°F ~ 109.2°F)
±0.2°C(±0.4°F) for 35.0°C~42.0°C (95.0°F~107.6°F)
±0.3°C(±0.5°F) for other range
20°C~60°C (68.0°F~140.0°F)
±2.0°C(±4.0°F)
138.5(L)x40.0(W)x32.6(H)mm( ±2mm)
About 72g (without battery)
15.0°C~40.0°C (59.0°F~104.0°F) with a relative humidity
of 15%~85%, Atmosphere pressure: 700hPa-1060hPa
10.0°C~40.0°C (50.0°F~104.0°F) with a relative humidity
of 15%~85%, Atmosphere pressure: 700hPa-1060hPa
-20°C~55°C (-4°F~131°F) with a relative humidity of
15%~90%, Atmosphere pressure: 700hPa-1060hPa
With a new battery (Carbon) approx. 10 months based
on the use frequency at 5 times/day.
IP22
Internally powered/Continuous Operation
•The reference site is core, the mode is adjusted mode.
•This thermometer is intended for home use by customer only. The measure site is forehead.
•This infrared thermometer meets requirements established in ASTM Standard E 1965-98 for the
thermometer system. Full responsibility for the conformance of the product to the standard is
assumed by MOBI Technologies Inc. Los Angeles, CA, 90015.
•ASTM laboratory accuracy requirements for the thermometer only in the display range of 98 °F to
102.2 °F (37 °C to 39 °C) for infrared thermometers is ± 0.4 °F (± 0.2 °C), whereas for mercury-in-glass
and electronic thermometers, the requirement per ASTM Standards E 667-86 and E 1112-86 is ± 0.2
°F ( ± 0.1 °C).
Equipment Symbols
Caution
Compliance with WEEE Standard
Refer to Operating Instructions
Operating atmospheric pressure
Operating Temperature
Serial number

Operating Humidity
Recyclable
Manufacturer
Date of Manufacture
IP22: The first number 2: Protected against solid foreign objects to 12.5mm Φ and greater.
The second number: Protected against vertically falling water drops, when enclosure titled
up to 15°.
Product Safety & Warnings
WARNING:
WARNING:
WARNING:
WARNING:
WARNING:
This product was designed to measure human body temperature on the forehead, do not use
this for any other purpose.
Do not use this thermometer if it has been malfunctioning or broken or damaged.
This product is not waterproof. Do not use this product under any wet conditions and do not
immerse in any liquid or water.
This product should not be left alone with children or pets when not in use by an adult.
Do not store the thermometer in extreme temperatures below (-4°F / -20°C) or over (131°F/
55°C).
Limited Product Warranty
MOBI® warrants its products to be free from defects in material and workmanship for period of (1 Year)
from the date of purchase. Should the product prove to be defective at any time during the warranty
period, we would either replace or repair the product at our option without charge. After the warranty
period, a service charge will apply for replacement of parts and labor costs. To obtain warranty service, you
must return the product complete with its original parts & accessories along with a copy of the original
purchase, gift, or registry receipt to us. This warranty does not cover damage caused by any tampering,
accident, misuse, abuse, improper maintenance, unauthorized modification, or connection to an improper
power supply. There will be a charge for repair caused for such damage. This warranty becomes void upon
purchase from an unauthorized, third-party seller. This warranty excludes all incidental or consequential
damages and any liability other than stated above.
Questions?
Please visit: www.getmobi.com
Support Portal: https://mobisupport.zendesk.com
Support Ticket: https://www.getmobi.com/gethelp
© 2022 MOBI Technologies, Inc.
All Rights Reserved