Mocka Essentials 6 Cube User manual

Phillips & Flathead screwdrivers required *We recommend using a Flathead screwdriver to tighten all locking nuts 100% before first use.
Please clear any loose wood from the locking nut holes before inserting the nut to ensure it locks 100%.
WARNING: Any furniture that is not anchored to a wall has the potential to tip
over in certain circumstances, i.e. if a child attempts to climb up on the furniture
or in the event of an earthquake. Accordingly, we recommend that all furniture
is anchored to a wall. We supply a free safety wall anchor with all furniture sold
and we recommend these are used to prevent your product tipping. The fixing
device provided should fit most wall types, but please note that different wall
materials may require different fixing devices from those supplied.
Hardware Supplied
x28
B
A
x28
CD
EF G HIJ
x8
x4
x3
x6
x6 x18
x3
x28
8 mm
12 mm
35 mm
x1
washer
Z
Wall
Screw
r/washer
screw
x1
Y
wall
anchor
x1
X
Safety
Strap
W
Wall Strap
1
mocka.co.nz | mocka.com.au
Mocka Essentials 6 Cube
Assembly Instructions
Thank you for your purchase.
Please follow the instructions below for correct assembly.

12
First, screw hardware (B) into all side panels [1, 3, 5 and 7]. Starting with [1] and
[3], slide both panels together with the middle shelf [2], making sure the grooved
ends line up. Insert hardware (A) into the holes on the middle shelf and tighten
with a screwdriver. Using the same process, join together [3, 4, 5, 6 and 7].
Use screws (H) to mount hinge pins (F) to all three cupboard
doors [9]. Fasten clip plate (E) with screws (H) beside the door
handle.
x
A
B
x
3
1
4
2
B
A
7
5
6B
9
x1
H
E
x2
H
F
x3
Cupboard Doors
2
mocka.co.nz | mocka.com.au
Mocka Essentials 6 Cube
Assembly Instructions

12
First, screw hardware (B) into all side panels [1, 3, 5 and 7]. Starting with [1] and
[3], slide both panels together with the middle shelf [2], making sure the grooved
ends line up. Insert hardware (A) into the holes on the middle shelf and tighten
with a screwdriver. Using the same process, join together [3, 4, 5, 6 and 7].
Use screws (H) to mount hinge pins (F) to all three cupboard
doors [9]. Fasten clip plate (E) with screws (H) beside the door
handle.
x
A
B
x
3
1
4
2
B
A
7
5
6B
9
x1
H
E
x2
H
F
x3
Cupboard Doors
34
Screw hardware (B) into base panel [10]. Place base panel on top while
sliding the ends of (B) into holes on the top of side panels. Make sure the
door hinger pin (F) also fits into base panel [10]. Insert and tighten
hardware (A).
Slide cupboard back panel [8] into grooves as shown. Screw hinge pins
(F) into the holes in the cupboard door. Lower door into pin hole in
middle shelf [4].
8
9
10
B
A
A
x8
7
4
F
3
mocka.co.nz | mocka.com.au
Assembly Instructions
Mocka Essentials 6 Cube

56
Attach feet blocks (D) to base panel [10] using long screws (C) and the
pre-drilled holes. Fasten clip plate (E) to the cupboard door. Attach
magnetic clip (I) inside the cupboard as shown using screws (G).
Flip the unit over so the feet stand on the floor. Slide both back panels
[8] into grooves as shown. Screw hinge pins (F) into the holes in both the
cupboard doors. Lower doors into pin hole in shelves [2] and [6].
8
8
9
9
C
D
x1
G
I
10
Mocka Essentials 6 Cube
Assembly Instructions
4
mocka.co.nz | mocka.com.au

Jolt Wardrobe
ASSEMBLY INSTRUCTIONS
5
mocka.co.nz | mocka.com.au
56
Attach feet blocks (D) to base panel [10] using long screws (C) and the
pre-drilled holes. Fasten clip plate (E) to the cupboard door. Attach
magnetic clip (I) inside the cupboard as shown using screws (G).
Flip the unit over so the feet stand on the floor. Slide both back panels
[8] into grooves as shown. Screw hinge pins (F) into the holes in both the
cupboard doors. Lower doors into pin hole in shelves [2] and [6].
8
8
9
9
C
D
x1
G
I
10
78
Screw hardware (B) into top panel [11]. Place panel on top of side
panels while sliding the ends of (B) into the holes. Insert bolts (A).
Fasten clip plates (E) to upper doors and attach magnetic clip (I) inside
the cupboard.
Check all doors can swing and close easily. Tighten all locking nuts (A).
Use stickers (J) to cover all holes where hardware (A) is used.
x2
G
I
11 B
A
A
x8
Mocka Essentials 6 Cube
Assembly Instructions
5
mocka.co.nz | mocka.com.au

910
Once assembled lift furniture into place, do not drag. Attach the safety
strap (W) to the top of the back side of the unit using screw (Y). Tighten
with a screwdriver.
Move unit into desired location up against a wall. Use a drill to create a
small hole lining up with the top of the safety strap (W). Fasten to wall
using wall anchor (X), washer (Z) and screw. Ensure the unit is balanced
and steady before use. You’re done, enjoy!
Y
W
x1
Y
W
WZx1
Wall Strap
X
wall
screw
Washer
Strap
wall
anchor
wall
screw
Mocka Essentials 6 Cube
Assembly Instructions
6
mocka.co.nz | mocka.com.au