MULTISPAN UTC-222 User manual

POWER ON
   . . . .



   . . . .

All digit segment will be turned ON for 3 sec
Previous or default sensor input will be display for 2 sec
Process Value
UTC-122,222 UTC-422
Set Value
POWER ON




   

1) Press Key to enter in to an instrument.
2) Press Key to go to next parameter.
4) Press Key to save change in setting
5) To start or stop Auto-Tunning press key for 6 sec.
6) Press Or key for 3 sec to go to factory setting mode.
3) Use Or key to change value of parameter.
J: 0 to 600°C / K: 0 to 1200°C /
PT-100: -99 to 400ºC /PT.1: -99.0 to 400.0°C
PID / ON-OFF (selectable)
Output 1
Output 2
Power Supply 100 to 250V AC, 50 / 60 Hz smps
Model
Display
Size
Panel Cutout
Input
Temperature
Range
Control Action
UTC-122
96 X 96 X 50
92 X 92 68 X 68 44 X 44
72 X 72 X 85 48 X 48 X 95
UPPER:- 4 Digit 7 seg 0.56”,red LED Display UPPER:- 4 Digit 7 seg 0.39”,red LED Display
LOWER:- 4 Digit 7 seg 0.4”,green LED Display LOWER:- 4 Digit 7 seg 0.28”,green LED Display
UTC-222 UTC-422
J, K, PT-100 (selectable)
1st Output : Relay Or SSR,12V DC,30mA
2nd Output: Relay
OPERATING MANUAL
UNIVERSAL TEMPERATURE CONTROLLER
www.multispanindia.com
Page - 1
UTC 122 UTC 222
UTC-122,222 & 422

 

UTC 422


Technical Specification
Key Operations
UTC 122
UTC 222
UTC 422

www.multispanindia.com
Page - 2
BASIC CONFIGURATION
SET POINT SETTING Set Value
Set Point 1
Set Point 2


 Password Message




Press key for 5 sec to enter
Password parmeter
 Process Value
 Input ( J / K / Pt.1 / Pt100 )
Control Action
Set2 Mode
Individual/Relative


PID/ON-OFF
 Password Message
Press ENT key to Save & Exit
Press SET key


 
 
 .K
Set Point Low Limit
Set Point High Limit




OFF-SET


TO ENTER BASIC
CONFIGURATION
SETTING, ENTER “73”

www.multispanindia.com
Page - 3
 Password Message

PID 













Parameters
Proportional
Constant
Integral
Constant
Derivative
Constant
Cycle Time
Manual Reset
Cool HYS
CONTROL PARAMETER
TO ENTER CONTROL
PARAMETER
SETTING, ENTER “37”
Press ENT key to Save & Exit
IF PID SELECTED IF ON-OFF SELECTED
 ON-OFF
Parameters

Hysteresis 1

Off-set correction -20.0°C to +20.0°C
-20°C to +20°C
CT 4 sec to 99 sec
IC 0.000 to 9.999
Hysteresis 0.1°C to 50.0°C
1°C to 50°C
MR -9.0 to +9.0 -9 to +9
DC 0 to 9999
PC
Sr.
1
2
3
4
5
6
7
00.00 to 99.99
Parameter Range for PT.1 sensorRange for J, K, PT100

Product improvement and upgrade is a constant procedure. So for more updated operating informationand support, please
contact our Helpline : [phone]/75 or Email at [e-mail] www.multispanindia.com
Page - 4
FACTORY SETTING
FACTORY SETTING
PARAMETER
IC
CT
OFFSET
PC
DC
MR
HYSTERESIS
VALUES
0.225
6 sec
000.5
25
0°C
0°C
1°C
SR.
2
4
6
1
3
5
7
Process Value
Set Value
Factory Setting
Press + key for 3 sec

 : press key to apply factory set values as shown in table. : press key to escape from factory setting.
1) Connection Diagram
UTC 122 UTC 222 UTC 422
NO
RELAY-1
O/P
S.S.R
C
NC
8
9
12
10
13
11
14
1
2
5
3
6
4
7
100-250V AC
(SMPS)
SUPPLY
L
N
T/C
NO
RELAY-2
NC
C
N
L
C
CNO
NO NC
RELAY-1
RELAY-2
SUPPLY
100-250V AC
(SMPS)
T/C
S.S.R
O/P
NNO NO
RELAY-1
O/P
S.S.R
RELAY-2
NC NC
CC
100-250V AC
(SMPS)
SUPPLY
L
T/C
1
1
10
20
2
2
9
19
3
3
8
18
4
4
7
17
55
6
16
6
15
7
14
8
13
9
12
10
11