MULTISPAN UTC-423 User manual

   

1) Press Key to enter in to an instrument.
2) Press Key to go to next parameter.
4) Press Key to save change in setting
5) To start or stop Auto-Tunning press keyfor 6 sec.
6) Press Or keyfor 3 sec to go to factory setting mode.
3) Use Or key to change value of parameter.
J: 0 to 600 C / K: 0 to 1200 C /
PT-100: -99 to 400 C /PT.1: -99.0 to 400.0 C
° °
º °
PID / ON-OFF (selectable)
Output 1
Output 2
Output 3
Power Supply 100 to 250V AC, 50 / 60 Hz smps
Model
Display
Size
Panel Cutout
Input
Temperature
Range
Control Action
44 X 44
48 X 48 X 95
UPPER:- 4 Digit 7 seg .39”,red LED Display
LOWER:- 4 Digit 7 seg .28”,greenLED Display
UTC-423
J, K, PT-100 (selectable)
1st Output : Relay or S.S.R
2nd Output: Relay or S.S.R
3rd Output: Relay or S.S.R
OPERATING MANUAL
UNIVERSAL TEMPERATURE CONTROLLER
www.multispanindia.comPage - 1
UTC-423
UTC-423
Technical Specification
Key Operations
UTC-423
AL
H
B



www.multispanindia.com
Page - 2
BASIC CONFIGURATION
SET POINT SETTING SET VALUE
SET POINT 1
H
B
AL
SET POINT 2
SET POINT 3




Password Message





Press key for 3 sec to
enter Password parameter
 PROCESS VALUE
 Input ( J / K / Pt100 / Pt.1 )
Control Action
Set2 Mode
Set3 Mode
Time 3 Mode
Time 3 Unit
Individual/Relative
H-AL/L-AL/I-AL/O-AL/OFF
ALMT/OFF
SEC/MIN/HOUR





PID/ON-OFF
 Password Message
Press ENT key to Save & Exit


 







 
  
  .K
TO ENTER BASIC
CONFIGURATION
SETTING, ENTER “73”
Set Point Low Limit


Set Point High Limit


OFF-SET


Press SET key

www.multispanindia.com
Page - 3
 Password Message

PID


















Parameters
Proportional
Constant
Integral
Constant
Derivative
Constant
Cycle Time
Manual Reset Cool HYS
CONTROL PARAMETER
TO ENTER CONTROL
PARAMETER
SETTING, ENTER “37”
Press ENT key to Save & Exit
IF PID SELECTED IF ON-OFF SELECTED
 ON-OFF
Parameters

Hysteresis 1


Product improvement and upgrade is a constant procedure. So for more updated operating information and support, please
contact our Helpline :[phone]/75 or Email at [e-mail]
www.multispanindia.com
Page - 4
FACTORY SETTING
FACTORY SETTING
PARAMETER
IC
CT
OFFSET
PC
DC
MR
HYSTERESIS-2
HYSTERESIS-3
HYSTERESIS
VALUES
0.225
6 sec
05.00
25
0°C
0°C
1°C
1°C
1°C
SR.
2
4
6
1
3
5
7
8
9
Process Value
Set Value
Factory Setting
Press + key for 3 sec
Connection Diagram For Relay:
Connection Diagram For S.S.R:
N
L
CCC H
B
C
NO
FOR AL
NONO
NC
N
L
H
AL
B
-
-
-
+
++
SSR
SSR
SSR
Off-set correction -20.0 C to +20.0 C° °
-20 C to +20 C° °
CT 4 sec to 99 sec
IC 0.000 to 9.999
Hysteresis 0.1 C to 50.0 C° °
1°C to 50°C
MR -9.0 to +9.0 -9 to +9
DC 0 to 9999
PC
Sr.
1
2
3
4
5
6
7
00.00 to 99.99
Parameter Range for PT.1 sensor
Range for J, K, PT100