Murdock A171-UG-SO Series Installation and operating instructions

7020-983-001
I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S
DRINKING FOUNTAIN
Date: 08/16/18
A171-UG-SO, A171-UG Series, and A171-UG-VR Series
Barrier Free, Wall Mounted Drinking Fountain
COMPLIES WITH
Test rating conditions are
compliant with ARI 1010.
Federal
Public Law
111-380
(No Lead) Member of
MURDOCK
15125 Proctor Ave.
City of Industry, CA
91746 U.S.A.
Phone [phone]
626-336-4561
Fax [phone]
www.murdockmfg.com
NOTES TO INSTALLER:
1. Please leave this documentation with the owner of the fixture when finished.
2. Please read this entire booklet before beginning the installation.
3. Check your installation for compliance with plumbing, electrical and other applicable codes.
This warranty does not cover installation or labor charges and does not apply to materials, which have been
damaged by other causes such as mishandling or improper care or abnormal use. The repair or replacement of the
defective materials shall constitute the sole remedy of the Buyer and the sole remedy of Murdock under this
warranty. Murdock shall not be liable under any circumstances for incidental, consequential or direct charges
caused by defects in the materials, or any delay in the repair or replacement thereof. This warranty is in lieu of all
other warranties expressed or implied. Product maintenance instructions are issued with each unit and disregard
or non-compliance with these instructions will constitute an abnormal use condition and void the warranty.
Stainless steel must be protected on job site during construction and must be properly maintained after the water
has been introduced into the water cooler or drinking fountain, or Mudock’s limited warranty is void.
LIMITED EXPORT WARRANTY - One year on parts only.
LIMITED WARRANTY - UNITED STATES & CANADA
Murdock warrants that its products are free from defects in material or workmanship under normal use and
service for a period of one year from date of original shipment or for 18 months after the date of shipment from the
factory, whichever comes first. Murdock’s liability under this warranty shall be discharged solely by replacement
or repair of defective material, provided Murdock is notified in writing within one year from date of shipment,
F.O.B. Industry, California.
Murdock assumes no responsibility for use of void or
suspended data. © Copyright Murdock, City of
Industry, CA Member of Morris Group International.
Please visit www.murdockmfg.com for most
current specifications.
A171100F-UG-SO / A171400F-UG-SO / A171100S-UG-SO / A171400S-UG-SO
A171100F-UG / A171400F-UG / A171100S-UG / A171400S-UG
171100F-UG-VR / A171400F-UG-VR / A171100S-UG-VR / A171400S-UG-VR
TECHNICAL ASSISTANCE TOLL FREE TELEPHONE NUMBER:
1.800.591.9360
Technical Assistance Fax: [phone]
A171100F-UG-SO A171100F-UG A171400S-UG-VR

7020-983-001
MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA
Phone [phone] or 626-333-2543 • Fax [phone] • www.murdockmfg.com Member of
A171-UG Revised: 09/01/2020
Page 2 of 17
NOTICE
A dielectric coupling must be used to connect the drinking fountain to the water supply . A nonmetallic coupler is furnished with
this drinking fountain to meet this requirement.
ROUGHING-IN AND DIMENSIONAL DRAWING
Prior to roughing consult with local, state, and federal codes for proper mounting height.
NOTES: Dimensions indicated ** are for ADA frontal approach installation. Adjust vertical dimension *
as required to comply with federal, state, and local codes. For Child ADA compliant parallel approach,
decrease spout height to 30” maximum above finished floor.
1-1/4" [32] O.D.
TAILPIECE FOR
P-TRAP BY
OTHERS
A
B
C
E
D
A. 3/8" O.D. SUPPLY INLET
B. WASTE OUTLET FOR P-TRAP BY OTHERS FOR PROVIDED
1-1/4" O.D. TAILPIECE
C. ELECTRICAL SERVICE ROUGH FOR -BF12 IF REQUIRED OR
SPECIFIED
D. Ø3/8" HANGER BRACKET PUNCHING, 4 PLACES
FOR ANCHORING HARDWARE BY OTHERS
E. Ø1/4" PUNCHING, 2 PLACES FOR ANCHORING HARDWARE
BY OTHERS
F. PUSHBUTTON ASSEMBLY OR SENSOR
G. CAULKING BEAD FOR OUTDOOR INSTALLATION
F
*
GENERAL NOTES:
1. ALL DIMENSIONS ARE IN INCHES [MM]
2. ALLOW 4 INCHES [102 MM] MINIMUM CLEARANCE PER SIDE
FOR VENTILATION
3. DIMENSIONS SHOWN ARE FOR ADA ADULT HEIGHT. ADJUST
VERTICAL DIMENSIONS AS NECESSARY TO COMPLY WITH
FEDERAL, STATE, & LOCAL CODES
4. STOP VALVE, P-TRAP, & ELECTRICAL OUTLET NOT SUPPLIED
5. IMPORTANT: COOLERS MUST BE ATTACHED TO WALL WITH
APPROPRIATE ANCHOR SCREWS
63
8"
[162]
123
4"
[324]
*305
8"
[778]
2"
[51]
*177
8"
[454]
43
8"
[111]
41
4"
[108]
*157
8"
[403]
31
2"
[89]
77
8"
[201]
TYP
2"
[51]
33
4"
[95]
*33"
[838]
13
8"
[35]
6"
[152]
181
2"
[470]
G
G
I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S
DRINKING FOUNTAIN

7020-983-001
MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA
Phone [phone] or 626-333-2543 • Fax [phone] • www.murdockmfg.com Member of
A171-UG Revised: 09/01/2020
Page 3 of 17
PRIOR TO INSTALLATION:
Important: some options may slightly alter installation. To ensure proper installation review the manual thoroughly and verify
Rough-Ins before beginning work. File this manual with the owner or maintenance personnel upon completion of installation.
— Fixture mounting requirements: industry standard wall construction, adequate to support the fixture and installer provided
wall anchors sufficient to secure the fixture.
— Inspect fixture and all parts for damages.
IMPORTANT:
1. Waste P-Trap, Water Supply Service Angle Stop Valve and 2” x 4” Electrical Plug-In Receptacle to be supplied by others
in accordance with local codes. sed for the Waste Connection.A P-Trap (by others) must be u
2. Water supply is 3/8” Outside Diameter Copper Tube. Waste is 1-1/4” Outside Diameter.
3. Completely flush supply lines of all foreign debris before connecting to fixture. Drinking Fountain designed to not affect
taste, odor, color, or sediment. Optional water filter (WF1) is available should any of these problems arise from the water
supply.
4. If possible, limit exposure of the Drinking Fountain to direct sun light. The actual surface temperature of a Drinking
Fountain in direct sunlight on a 90°F day, the Drinking Fountain would be about 140°F.
2. Remove the bottom cover from the drinking fountain and set aside in a safe place. Save the screws in a secure location for
re-use in later stages of installation.
7. For outdoor installation, see outdoor installation instructions (Page 5)
3. Hang the Drinking Fountain on the Hanger Bracket, ensuring the Bracket Tabs engage AND seat in the slots in the back of
the drinking fountain. Verify Drinking Fountain is level, left to right AND front to back from bottom of unit.
NOTE: The Bubbler Stream may be adversely affected if unit is not square and level. Bottom of unit and louvers should be
used as reference to verify unit is square and plumb.
INSTALLATION:
4. Anchor Drinking Fountain to wall at other mounting points in base. Shim lower rear mounting points to level unit if
necessary.
9. Per UPC 609.10- All building water supply systems in which quick acting valves are installed shall be provided with
devices to absorb the Hammer caused by high pressure resulting from the quick closing of the valve. These pressure-
absorbing devices shall be approved mechanical devices. Water pressure-absorbing devices will be installed as close as
possible to the Quick Closing Valve.
5. Thoroughly flush the 3/8” O.D. Supply Line and then connect drinking fountain to water supply Angle Stop Valve (by others)
with supplied 3/8” O.D. copper tube.
7. Warranty is voided if installation is not made following current Murdock Mfg. installation instructions and if components
are assembled to the fixture that is not approved by Murdock Mfg.
5. Do NOT solder Copper Tube when inserted into the Coupler as damage to the O-Ring will result.
8. Fixture operates within water pressure range of 20 to 105 PSIG (138 to 724 kPa). Murdock Mfg. will not warranty fixtures
damaged when connected to supply lines with flow pressure lower than 20 PSIG (138 kPa) or higher than 105 PSIG (724
kPa). A pressure regulator must be furnished by others on supply line if inlet pressure is greater than 105 PSIG (724 kPa).
6. All burrs must be removed from outside of cut Tubes before inserting into Coupler or other components.
1. Mount Hanger Bracket to wall horizontally level as shown in Roughing-In and Dimensional Drawing. NOTE: Adjust height
of Bracket if Bubbler outlet height is required to vary from that shown /indicated. Hanger Bracket MUST be securely
anchored to wall with fasteners sufficient to support 3 times the weight of Water Cooler.
NOTE: If wall cannot provide adequate support, order and install optional fixture support carrier.
NOTE: If replacing a competitors Water Cooler you may be able to use existing mounting bracket.
6. Make up 1-1/4” O.D. Waste Connection for P-Trap (by others) .
I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S
DRINKING FOUNTAIN

7020-983-001
MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA
Phone [phone] or 626-333-2543 • Fax [phone] • www.murdockmfg.com Member of
A171-UG Revised: 09/01/2020
Page 4 of 17
I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S
DRINKING FOUNTAIN

7020-983-001
MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA
Phone [phone] or 626-333-2543 • Fax [phone] • www.murdockmfg.com Member of
A171-UG Revised: 09/01/2020
Page 5 of 17
NOTE: THIS PROCEDURE NOT APPLICABLE FOR A171-UG OR A171-UG-SO, OR EITHER UNIT
WITH -BF11 OR -BF12 BOTTLE FILLERS
OUTDOOR INSTALLATION INSTRUCTIONS A171-UG-VR ONLY:
1. Caulk all around the basin where it contacts the wall and where apron contacts the wall as shown, to prevent rain water
from leaking into the cabinet. DO NOT CAULK THE REMOVABLE ACCESS COVER.
SIDE VIEW
FRONT VIEW
CAULKING
CAULKING
I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S
DRINKING FOUNTAIN

7020-983-001
MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA
Phone [phone] or 626-333-2543 • Fax [phone] • www.murdockmfg.com Member of
A171-UG Revised: 09/01/2020
Page 6 of 17
I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S
DRINKING FOUNTAIN
A171-UG & A171-VR-UG BI-LEVEL UNIT PIPING INSTALLATION (WITH -BF OPTIONS)
A171-UG-SO BI-LEVEL UNIT PIPING INSTALLATION
Water Supply
Tubing
Electronic Valve
Assembly
Cartridge Valve
Assembly
To Bottle Filler
Water Supply
Tubing
Remove For Bottle
Filler Use
Water Supply
Tubing
Water Supply
Tubing
Remove For
Bottle Filler Use
To Bottle
Filler

7020-983-001
MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA
Phone [phone] or 626-333-2543 • Fax [phone] • www.murdockmfg.com Member of
A171-UG Revised: 09/01/2020
Page 7 of 17
NOTE: FITTINGS AND TUBE SHOULD BE KEPT
CLEAN, BAGGED AND UNDAMAGED PRIOR TO
INSTALLATION.
PUSH-IN FITTING INSTALLATION
2. Pull on the fitted tubing to ensure it is secure. Tube
should not come free from the fitting. Water test the
connection assembly prior to leaving the site to ensure
there are no leaks.
DISCONNECTING THE TUBE:
To disconnect the tube from the fitting ensure that the
water line is depressurized. Push collet square towards
the push-in fitting body and hold. While holding the collet
in, pull on the PE tubing to remove from the push-in fitting.
TO CUT TUBE:
Cut to fit length of 1/4” PE tubing and remove any burrs
or sharp edges. Ensure that the outside diameter is free
from score marks. Tube ends should be square.
1. Firmly and fully insert the tubing end into the push-in
fitting up to the tube stop located approximately ½”
deep.
INSERTING THE TUBE:
COLLET
COLLET
O-RING
O-RING
TUBE STOP
COLLET
COLLET
COLLET
I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S
DRINKING FOUNTAIN

7020-983-001
MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA
Phone [phone] or 626-333-2543 • Fax [phone] • www.murdockmfg.com Member of
A171-UG Revised: 09/01/2020
Page 8 of 17
1. Strainer plug must be removed before cartridge replacement and strainer
maintenance (no need to turn the water off at the angle stop). Some residual water will drain
during plug removal.
2. Clean strainer as needed using clean water.
3. Cartridge replacement - insert diamond end of the universal tool into push button, rotate 90 degrees
and pull firmly to remove the button. Remove cartridge retaining nut . Remove and replace cartridge.
When replacing cartridge be sure to align the inlet and outlet ports on the cartridge with the ports in
the valve body.
—NOTE: STRAINER SCREEN MUST BE IN PLACE FOR
WATER TO FLOW.
CLEANING & MAINTENANCE GUIDE:
1. Periodically remove access panels and clean out in-line strainer.
3. Exterior panels can be cleaned using mild household detergents or warm, soapy water. Extra care
must be used cleaning chrome plated items and mirror finished stainless steel. They can scratch
easily and should only be cleaned using a clean, soft cloth and mild soap with water or a mild glass
cleaner.
CARTRIDGE REPLACEMENT/ STRAINER MAINTENANCE
2. Do NOT use harsh chemicals, abrasive or petroleum based cleaners. Use of these will void the
Acorn warranty.
Note: Use the universal maintenance tool to perform the following:
2
4
3
1
5
CARTRIDGE VALVE PARTS
BREAKDOWN
ITEM PART NUMBER DESCRIPTION
5 7003-830-000 UNIVERSAL MAINTANANCE TOOL
4 7003-864-000 STRAINER FILTER SCREEN
3 7003-097-001 O-RING &STRAINER PLUG
2 7000-060-000 FLOW REGULATOR CARTRIDGE(05 GPMG)
1 7003-095-001 VALVE ASSEMBLY
I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S
DRINKING FOUNTAIN

7020-983-001
MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA
Phone [phone] or 626-333-2543 • Fax [phone] • www.murdockmfg.com Member of
A171-UG Revised: 09/01/2020
Page 9 of 17
I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S
DRINKING FOUNTAIN
3. Cartridge replacement - Rotate and remove -VR pushbutton escutcheon 6 to release pushbutton 7 and springs 8 9 to
access cartridge.
6. Install button assembly items 6 7 8 9 using maintenance tool 5 . Insure springs are installed in button correctly.
4. Remove cartridge retaining nut 10 . Remove and replace cartridge 2 . When replacing cartridge be sure to align the inlet
and outlet ports on the cartridge with the ports in the valve body.
5. Install item 10 using maintenance tool 5 (Be careful not to over tighten)
7. Reinstall strainer 4 and plug 3 using maintenance tool 5 .
-VR VANDAL RESISTANT CARTRIDGE REPLACEMENT/ STRAINER MAINTENANCE
Note: Use the -VR maintenance tool to perform the following:
1. Strainer plug 4 must be removed before cartridge replacement and strainer
maintenance (no need to turn the water off at the angle stop). Some residual water will drain
during plug removal.
2. Clean strainer 4 as needed using clean water.
NOTE: STRAINER FILTER SCREEN
MUST BE IN PLACE FOR
WATER TO FLOW.
ITEM PART NUMBER DESCRIPTION
1 7003-095-001 VALVE ASSEMBLY
2 7000-060-000 FLOW REGULATOR CARTRIDGE(0.5 GPM)
3 7003-097-001 O-RING &STRAINER PLUG
4 7003-864-000 STRAINER FILTER SCREEN
5 7003-194-199 (-VR) MAINTENANCE TOOL
6 7003-197-199 (-VR) PUSHBUTTON ESCUTCHEON, CHROME
7 7003-196-199 (-VR) PUSHBUTTON, CHROME
8 7003-195-000 (-VR) PUSHBUTTON OVERTRAVEL SPRING
9 7003-193-000 (-VR) PUSHBUTTON RETURN SPRING
10 7000-052-000 RETAINING NUT
2
4
3
1
5
5
6
7
8
9
10

7020-983-001
MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA
Phone [phone] or 626-333-2543 • Fax [phone] • www.murdockmfg.com Member of
A171-UG Revised: 09/01/2020
Page 10 of 17
I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S
DRINKING FOUNTAIN
ITEM # PART NUMBER DESCRIPTION
1 7000-050-001 Valve Cartridge Assembly
2 7000-060-000
Valve Cartridge
3 7000-053-199 Jam Nut
-SO SENSOR OPERATED CARTRIDGE VALVE PARTS BREAKDOWN
-SO SENSOR OPERATED WIRING DIAGRAM WITH -BF12
WHITE
CAP
WHITE
CAP
WHITE
PLUG
WHITE
PLUG
BOTTLE FILLER
SOLENOID VALVE
BOTTLE FILLER
SENSOR
RED
PLUGS
RED
CAPS
TRANSFORMER
RED
CAP
RED
PLUG
FOUNTAIN
SOLENOID VALVE
FOUNTAIN
SENSOR

7020-983-001
MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA
Phone [phone] or 626-333-2543 • Fax [phone] • www.murdockmfg.com Member of
A171-UG Revised: 09/01/2020
Page 11 of 17
E. Once red light within sensor begins flashing
quickly, move hand to preferred activation
distance and hold there until light stops
flashing.
D. Within 5 seconds of making the connection to
the power supply, place and hold hand 2" to
4" in front of sensor.
C. Reconnect the sensor to the power supply.
SENSOR RANGE ADJUSTMENT
A. Disconnect sensor from power supply.
B. Create a short circuit between the positive
and negative connections on the sensor for
five seconds. WARNING: Do NOT create a
short circuit on the power supply or while the
sensor is connected to the power supply.
Check sensor activation distance. If
unsatisfactory, repeats steps A through E.
Disconnect from power supply.
A
Jumper by
others
Short circuit sensor for 5 seconds.
B
Reconnect sensor to power supply.
C
Within 5 seconds, place hand
in front of sensor.
D
Move hand to desired range.
E
FOR A171.8-UG-SO ONLY

7020-983-001
MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA
Phone [phone] or 626-333-2543 • Fax [phone] • www.murdockmfg.com Member of
A171-UG Revised: 09/01/2020
Page 12 of 17
-Removal of P.E. Tubing from
Universal Maintenance Tool
-Button Removal
-Cartridge Retaining Nut
-Strainer Plug
Push-in Fittings
NOTE: See next page for table of part numbers corresponding to drawing above.
20
I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S
DRINKING FOUNTAIN
NOTE:
** Flow Restrictor Only Available
With Low Flow Bubbler.
A171-UG DRINKING FOUNTAIN PARTS BREAKDOWN
NOTE: See page #10 for fixture drawing corresponding to table of parts below.
5
4
3
2
1
6
7
11
10
19
13
12
1518"
14
20
15 6"
8
17
18
16
13 15"
9
9

7020-983-001
MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA
Phone [phone] or 626-333-2543 • Fax [phone] • www.murdockmfg.com Member of
A171-UG Revised: 09/01/2020
Page 13 of 17
Repairs must be made with Murdock Manufacturing parts only. Please order through your local
representative or distributor. The phone number to locate your local representative is 1.800.591.9360.
I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S
DRINKING FOUNTAIN
A171-UG DRINKING FOUNTAIN PARTS BREAKDOWN TABLE
NOTE: See previous page (9) for fixture drawing corresponding to table of parts below.
ITEM # PART NUMBER DESCRIPTION
1 7003-161-001 BASIN TOP w/ PLUG
7000-099-002 STANDARD FLEXIBLE BUBBLER ASSEMBLY
7000-012-001 LEAD -FREE STAINLESS STEEL BUBBLER ASSEMBLY
3 0124-008-000 #8 x 3/4" LG FLAT HD SELF TAPPING TORX C/R SCREW
4 7000-006-000 FLAT DRAIN GASKET
5 7003-180-000 DRAIN ADAPTER
6 0250-036-000 #8 x 1/2" LONG TORX ROUND HEAD C/R SCREW
7 7003-950-199 HANGER BRACKET
8 7003-900-199 BACK PANEL
9 7003-007-199 SUPPORT STRUT
7003-951-020 COVER - GRAY
7003-035-299 COVER - STAINLESS STEEL
11 0124-031-000 #8x3/8" LONG SLOTTED HEX WASHER HEAD SCREW
12 7003-095-001 VALVE ASSEMBLY
7003-953-020 APRON ASSEMBLY - GRAY
7003-826-001 APRON ASSEMBLY - STAINLESS STEEL
14 7003-093-001 FLOW RESTRICTOR - LOW-FLOW BUBBLER ONLY
15 2169-000-000 1/*4" O.D. PE TUBING (BLUE)
16 1895-710-000 1/4" x 3/8" O.D. TUBE UNION TEE (PUSH-IN)
17 1895-715-000 1/4" PLUG
18 1895-123-000 1/4" x 3/8" O.D. PUSH-IN SUPPLY INLET CONNECTION
19 7003-099-000 PUSHBUTTON
20 7003-830-000 UNIVERSAL MAINTENANCE TOOL
2
13
13

7020-983-001
MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA
Phone [phone] or 626-333-2543 • Fax [phone] • www.murdockmfg.com Member of
A171-UG Revised: 09/01/2020
Page 14 of 17
I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S
DRINKING FOUNTAIN
NOTE: See next page for table of part numbers corresponding to drawing above.
-Button Removal
-Strainer Plug
Push-in Fittings
-Cartridge Retaining Nut
-Removal of P.E. Tubing from
Universal Maintenance Tool
28
NOTE:
** Flow Restrictor Only Available
With Low Flow Bubbler.
NOTE: See page #12 for fixture drawing corresponding to table of parts below.
A171-UG-VR DRINKING FOUNTAIN PARTS BREAKDOWN
5
4
3
2
1
13
12
18"
VANDAL RESISTANT BUTTON &
VALVE BREAKDOWN
NOT TO SCALE
12
19
20
21
22
23
24
21
25
20
26
27
5
4
3
2
1
6
7
11
10
15
14
28
15 6"
VANDAL RESISTANT BUTTON &
VALVE BREAKDOWN
NOT TO SCALE
8
17
16
18
15"
15
99

7020-983-001
MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA
Phone [phone] or 626-333-2543 • Fax [phone] • www.murdockmfg.com Member of
A171-UG Revised: 09/01/2020
Page 15 of 17
I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S
DRINKING FOUNTAIN
Repairs must be made with Murdock Manufacturing parts only. Please order through your local
representative or distributor. The phone number to locate your local representative is 1.800.591.9360.
A171-UG-VR DRINKING FOUNTAIN PARTS BREAKDOWN TABLE
NOTE: See previous page (11) for fixture drawing corresponding to table of parts below.
ITEM # PART NUMBER DESCRIPTION
1 7003-161-001 BASIN TOP w/ PLUG
7000-099-002 STANDARD FLEXIBLE BUBBLER ASSEMBLY
7000-012-001 LEAD -FREE STAINLESS STEEL BUBBLER ASSEMBLY
3 0124-008-000 #8 x 3/4" LG FLAT HD SELF TAPPING TORX C/R SCREW
4 7000-006-000 FLAT DRAIN GASKET
5 7003-180-000 DRAIN ADAPTER
6 0124-036-000 #8 x 1/2" LONG TORX ROUND HEAD C/R SCREW
7 7003-950-199 HANGER BRACKET
8 7003-900-199 BACK PANEL
9 7003-007-199 SUPPORT STRUT
7003-951-020 COVER - GRAY
7003-035-299 COVER - STAINLESS STEEL
11 0124-031-000 #8x3/8" LONG SLOTTED HEX WASHER HEAD SCREW
12 7003-095-001 VALVE ASSEMBLY
7003-952-020 APRON ASSEMBLY - GRAY
7003-211-001 APRON ASSEMBLY - STAINLESS STEEL
14 7003-093-001 FLOW RESTRICTOR - LOW-FLOW BUBBLER ONLY
15 2169-000-000 1/*4" O.D. PE TUBING (BLUE)
16 1895-710-000 1/4" x 3/8" O.D. TUBE UNION TEE (PUSH-IN)
17 1895-715-000 1/4" PLUG
18 1895-123-000 1/4" x 3/8" O.D. PUSH-IN SUPPLY INLET CONNECTION
19 7003-198-199 (-VR) PUSHBUTTON MOUNTING SLEEVE
20 0124-055-000 #8x3/4" PHILLIPS ROUND HEAD SCREW
21 0161-062-000 #6-32x1/2" S/S PHIL FLAT HEAD SCREW
22 7003-195-000 OVERTRAVEL SPRING
23 7003-196-199 (-VR) CHROME PLATED PUSHBUTTON
24 7003-197-199 (-VR) CHROME PLATED ESCUTCHEON
25 7003-193-000 PUSHBUTTON RETURN SPRING
26 7003-200-000 LOWER GASKET
27 7003-199-000 UPPER GASKET
28 7003-194-199 (-VR) UNIVERSAL MAINTENANCE TOOL
2
13
13

7020-983-001
MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA
Phone [phone] or 626-333-2543 • Fax [phone] • www.murdockmfg.com Member of
A171-UG Revised: 09/01/2020
Page 16 of 17
I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S
DRINKING FOUNTAIN
NOTE: See next page for table of part numbers corresponding to drawing above.
NOTE:
** Flow Restrictor Only Available
With Low Flow Bubbler.
A171-UG-SO DRINKING FOUNTAIN PARTS BREAKDOWN
NOTE: See page #14 for fixture drawing corresponding to table of parts below.
5
4
3
2
1
6
7
11
10
18
15 6"
12
13
21
14
242526
2223
1920
17
16
8
15 18"
15 15"
15
5"
9
9
27

7020-983-001
MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA
Phone [phone] or 626-333-2543 • Fax [phone] • www.murdockmfg.com Member of
A171-UG Revised: 09/01/2020
Page 17 of 17
I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S
DRINKING FOUNTAIN
Repairs must be made with Acorn Engineering parts only. Please order through your local representative or distributor. The
phone number to locate your local representative is 1.800.591.9360.
A171-UG-SO DRINKING FOUNTAIN PARTS BREAKDOWN TABLE
NOTE: See previous page (13) for fixture drawing corresponding to table of parts below.
ITEM # PART NUMBER DESCRIPTION
1 7003-161-001 BASIN TOP w/ PLUG
7000-099-002 STANDARD FLEXIBLE BUBBLER ASSEMBLY
7000-012-001 LEAD -FREE STAINLESS STEEL BUBBLER ASSEMBLY
3 0124-008-000 #8 x 3/4" LG FLAT HD SELF TAPPING TORX C/R SCREW
4 7000-006-000 FLAT DRAIN GASKET
5 7003-180-000 DRAIN ADAPTER
6 0124-036-000 #10 x 3/4" LONG TORX ROUND HEAD C/R SCREW
7 7003-950-199 HANGER BRACKET
8 7003-900-199 BACK PANEL
9 7003-007-199 SUPPORT STRUT
7003-951-020 COVER - GRAY
7003-035-299 COVER - STAINLESS STEEL
11 0124-031-000 #8 x 3/8" LONG SLOTTED HEX WASHER HEAD SCREW
12 7001-200-001 SOLENOID VALVE ASSEMBLY
7003-922-020 APRON ASSEMBLY - GRAY
7003-029-003 APRON ASSEMBLY - STAINLESS STEEL
14 7003-093-001 FLOW RESTRICTOR - LOW-FLOW BUBBLER ONLY
15 2169-000-000 1/*4" O.D. PE TUBING (BLUE)
16 1895-710-000 1/4" x 3/8" O.D. TUBE UNION TEE (PUSH-IN)
17 1895-715-000 1/4" PLUG
18 7000-021-002 "Y" STRAINER ASSEMBLY 3/8" O.D. x 1/4" O.D.
19 0711-407-001 240VAC / 9VDC TRANSFORMER
20 7003-028-199 TRANFORMER BRACKET
21 7000-050-001 VALVE CARTRIDGE ASSEMBLY
22 7000-060-000 FLOW REGULATOR CARTRIDGE (0.5 GPM)
23 7003-023-199 CARTRIDGE MOUNTING BRACKET (SENSOR OP)
24 2562-369-001 SENSOR ASSEMBLY, INFRARE, LATCHING
25 7003-027-199 SENSOR BRACKET
26 7001-200-199 SENSOR SPACER
27 0711-412-001 2 STATION 9VAC WIRING HARNESS
2
13
13