Mycond ROOMER Smart 25 User manual

user's manual
■
посібник
користувача
■
руководство
пользователя
1
AIR DEHUMIDIFIER
ROOMER Smart 25

ROOMER Smart 25
AIR DEHUMIDIFIER
USER’S MANUAL
3

eng 4
USER’S MANUAL
PLEASE KEEP THIS MANUAL FOR FURTHER REFERENCE!
Thank you for selecting our super quality dehumidifier. Please be sure to read this manual
carefully before using it. If you have any questions, please contact the professional service for
help. Keep the manual for further reference.
The dehumidifier will remove excess moisture from the air, creating a comfortable
environment for your home and oce. Its compact design allows you to easily move it to any
room.

5
CONTENTS
PRECAUTIONS ■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■ 6
SPECIFICATIONS ■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■ 11
APPEARANCE■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■ 12
OPERATION ■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■ 14
MAINTENANCE■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■ 22
TROUBLESHOOTING ■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■ 25

eng 6
PRECAUTIONS
Read the following notices carefully before operating this dehumidifier.
The warnings and notices must be observed effectively to ensure the safety of the operation.
1. This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or
mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning
use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance.
Cleaning and user maintenance shall not be made by children without supervision.
2. The unit is designed only for use with R-290 (propane) gas as the designated refrigerant. R-290 (propane) is flammable
and heavier than air.
3. The refrigerant loop is sealed. Only a qualified technician should attempt to service!
4. Do not discharge the refrigerant into the atmosphere.
5. If propane gas is present or even suspected, do not allow untrained personnel to attempt to find the cause.
6. The propane gas used in the unit has no odor.
7. If a leak is detected, immediately evacuate all persons from the store, ventilate the room and contact the local fire
department to advise them that a propane leak has occurred.
8. No open flames, cigarettes or other possible sources of ignition should be used inside or in the vicinity of the units.
9. Component parts are designed for propane and non-incentive and non-sparking. Component parts shall only be
replaced with identical repair parts.
10. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons
in order to avoid a hazard.
11. The appliance shall be disconnected from its power source during maintenance.
12. Always operate the unit from a power source of equal voltage, frequency and rating as indicated on the product
identification plate.
13. Always use a power outlet that is grounded.
14. Do not operate with wet hands. Prevent water from spilling onto the unit.
15. Do not immerse or expose the unit to rain, moisture or any other liquid.
16. Do not leave the unit running unattended. Do not tilt or turn over the unit.

7
17. Do not unplug while the unit is operating.
18. Do not use an extension cord or an adapter plug.
19. Do not put objects on the unit.
20. Do not insert fingers or other objects into the air outlet.
21. Do not touch the air inlet or the aluminum fins of the unit.
22. Do not operate the unit if it is dropped, damaged or showing signs of product malfunction.
23. Ensure the unit is far away from fire, inflammable, or explosive objects.
24. The unit shall be installed in accordance with national wiring regulations.
25. Do not use means to accelerate the defrosting process or to clean, other than those recommended by the manufacture.
26. The appliance shall be stored in a room without continuously operation sources (for example: open flames, an operating
gas appliance or an operating electric heater).
27. The appliance shall be stored so as to prevent mechanical damage from occurring.
28. Do not piece or burn, even after use.
29. Pipe-work shall be protected from physical damage and shall not be installed in an unventilated space, if that space is
smaller than 4m².
30. Compliance with national gas regulations shall be observed.
31. Keep any required ventilation openings clear of obstruction.
32. The appliance shall be stored in a well-ventilated area where the room size corresponds to the room area as specified for
operation.
PRECAUTIONS

eng 8
Any person who is involved with working on or breaking into a refrigerant circuit should hold a current valid certificate
from an industry-accredited assessment authority, which authorizes their competence to handle refrigerants safely in
accordance with an industry, recognized assessment specification.
Servicing shall only be performed as recommended by the equipment manufacturer. Maintenance and repair requiring
the assistance of other skilled personnel shall be carried out under the supervision of the person competent in the use
of flammable refrigerants.
If you don’t understand something or need help, please contact the dealer services
AFETY PRECAUTIONS ON SERVICING
Please follow these warnings when to undertake the following when servicing a dehumidifier with R290.
Checks to the area
Prior to beginning work on systems containing flammable refrigerants, safety checks are necessary to ensure that the
risk of ignition is minimized. For repair to the refrigerating system, the following precautions shall be complied with
prior to conducting work on the system.
Work procedure
Work shall be undertaken under a controlled procedure so as to minimize the risk of a flammable gas or vapor being
present while the work is being performed.
General work area
All maintenance staff and others working in the local area shall be instructed on the nature of work being carried
out. Work in confined spaces shall be avoided. The area around the workspace shall be sectioned off. Ensure that the
conditions within the area have been made safe by control of flammable material.
PRECAUTIONS

9
Checking for presence of refrigerant
The area shall be checked with an appropriate refrigerant detector prior to and during work, to ensure the technician is
aware of potentially flammable atmospheres. Ensure that the leak detection equipment being used is suitable for use with
flammable refrigerants, i.e. no sparking, adequately sealed or intrinsically safe.
Presence of fire extinguisher
If any hot work is to be conducted on the refrigeration equipment or any associated parts, appropriate fire extinguishing
equipment shall be available to hand. Have a dry powder or CO2 fire extinguisher adjacent to the charging area.
No ignition sources
No person carrying out work in relation to a refrigeration system which involves exposing any pipe work that contains
or has contained flammable refrigerant shall use any sources of ignition in such a manner that it may lead to the risk of
fire or explosion. All possible ignition sources, including cigarette smoking, should be kept sufficiently far away from the
site of installation, repairing, removing and disposal, during which flammable refrigerant can possibly be released to the
surrounding space. Prior to work taking place, the area around the equipment is to be surveyed to make sure that there are
no flammable hazards or ignition risks. “No Smoking” signs shall be displayed.
Ventilated area
Ensure that the area is in the open or that it is adequately ventilated before breaking into the system or conducting any hot
work. A degree of ventilation shall continue during the period that the work is carried out. The ventilation should safely
disperse any released refrigerant and preferably expel it externally into the atmosphere.
Checks to the refrigeration equipment
Where electrical components are being changed, they shall be fit for the purpose and to the correct specification. At all
times the manufacturer’s maintenance and service guidelines shall be followed. If in doubt consult the manufacturer’s
technical department for assistance.
PRECAUTIONS

eng 10
The following checks shall be applied to installations using flammable refrigerants:
The charge size is in accordance with the room size within which the refrigerant containing parts are installed;
The ventilation machinery and outlets are operating adequately and are not obstructed;
If an indirect refrigerating circuit is being used, the secondary circuit shall be checked for the presence of refrigerant;
Marking to the equipment continues to be visible and legible. Markings and signs that are illegible shall be corrected;
Refrigeration pipe or components are installed in a position where they are unlikely to be exposed to any substance
which may corrode refrigerant containing components, unless the components are constructed of materials which are
inherently resistant to being corroded or are suitably protected against being so corroded.
Checks to electrical devices
Repair and maintenance to electrical components shall include initial safety checks and component inspection
procedures. If a fault exists that could compromise safety, then no electrical supply shall be connected to the circuit
until it is satisfactorily dealt with. If the fault cannot be corrected immediately but it is necessary to continue operation,
an adequate temporary solution shall be used. This shall be reported to the owner of the equipment so all parties are
advised.
Initial safety checks shall include:
those capacitors are discharged: this shall be done in a safe manner to avoid possibility of sparking;
that there no live electrical components and wiring are exposed while charging, recovering or purging the system;
that there is continuity of earth bonding
PRECAUTIONS

11
Model No. ROOMER Smart 25
Power Supply AC220-240V/50Hz
Power Consumption 335W (27 °C, RH 60%)
380W (30 °C, RH 80%)
Rated Current 2.1A (27 °C, RH 60%)
2.2A (30 °C, RH 80%)
Dehumidifying Capacity 25L/Day (30 °C, RH 80%)
12L/Day (27 °C, RH 60%)
Water Tank Capacity 6.5L
Noise Level ≤45dB(A)
Refrigerant/Charge R290/75g
Temperature scope of application 5 °C – 35 °C
Suction Side Pressure 0.7MPa
Discharge Side Pressure 3.2MPa
Heat exchanger maximum allowable pressure 3.2MPa
Airflow 180 m³/hr
Dimension 395 × 290 × 653 mm
Net weight 14.5kg
Note: Specifications subject to change without notice.
SPECIFICATIONS

eng 12
APPEARANCE
Control Panel
Front shell
Air Outlet
Castors
3 Color
Digital Display

13
APPEARANCE
Air Filter
Continuous drainage
Handle
Water tank

eng 14
INSTALLATION
1. Place the unit on a firm, level surface in an area with at least 30cm of free space around it to allow for proper air
circulation.
2. Never install the unit where it could be subject to:
Heat sources such as radiators, heat registers, stoves or other products that products that produce heat.
In an area where oil or water may be splashed
Direct sunlight
Mechanical vibration or shock
Excessive dust
Lack of ventilation, such as cabinet or bookcase
Uneven surface
20 cm
OPERATION

15
OPERATING THE DEVICE SAFELY
Check the device after unpacking for any damages or scratches on it.
Operate this unit in an ambient temperature from 5°C to 32°C.
Do not use in the outdoors. This dehumidifier is intended for indoor residential applications only.
Do not operate in close proximity to walls, curtains, or other objects that may block inlet and outlet.
Keep the air inlet and outlet free of obstacles.
Adjusting the wind deflector in the upward direction prior to start up.
If tipped more than 45°, allow the unit to set upright for at least 24 hours before start up.
Keep doors and windows close for better energy saving.
Do not operate or store the unit in direct sunlight or rain.
It is normal for air outlet to feel warm to touch after continuous operation on hot days.
Empty the water tank before moving the device.
Make sure the water tank is correctly fitted otherwise the unit will not operate properly.
The dehumidifier starts up in the mode selected when the unit was last used.
The dehumidifier starts dehumidifying if the room humidity is 3% higher than the selected humidity.
There is a protective 3-minutes time delay of the compressor. Wait 3 minutes for the dehumidifier to resume
dehumidification.
OPERATION

eng 16
DIGITAL DISPLAY
Ambient humidity < 45%, it shows blue
45% ≥ ambient humidity ≤ 65%, it turns green
ambient humidity > 65%, it displays red
CONTROL PANEL
OPERATION

17
POWER
When you plug in the unit, a beep sounds and the “POWER”LED lights up.
Press the on/o switch to turn the unit on; the dehumidifier starts with the settings (except the timer setting) of the last
operation.
Press the on/o switch again to switch the unit o. The compressor switches o immediately and the fan switches o
with a delay of 30 seconds.
After a power failure, the unit restarts automatically with the settings (except the timer setting) of the last operation.
MODE
Auto mode Auto
The unit is equipped with a modern hygrostat (humidity controller) and switches o automatically after reaching the
desired humidity in order to save energy. The compressor switches o first and then the fan 30 seconds later. When the
humidity in the room rises again, the dehumidifier switches on automatically.
When automatic mode is activated, the target humidity can be set between 30% and 80% in 5% steps using the two
arrow keys.
The dehumidifier starts dehumidifying when the room humidity is at least 3% higher than the set target humidity.
Continuously drying mode
In continuous operation, the unit works continuously until the water tank is full or the dehumidifier is switched o
manually.
In this mode, the unit operates at maximum air output to dehumidify the room air as quickly as possible.
During operation, the current humidity is shown on the display.
OPERATION

eng 18
TIMER
Press the timer key to start the timer function. Then use the two arrow keys to set the desired run/start time from
1-24 hours. If the timer is activated, this is indicated by the corresponding LED.
If you activate the timer during operation, the appliance switches o after the set time.
If you activate the timer while the unit is in standby mode, the unit will start automatically after the set time has
elapsed.
To switch o the timer, press the key again and set the running time to “00” using the two arrow keys.
If the unit is switched o via the on/o switch, the timer function is also deactivated.
Note: when press POWER will also exit the timer setting.
SPEED
The fan speed can only be changed in automatic mode.
Press this button to switch between the two fan speeds.
The currently selected fan speed is displayed via the two LEDs.
Increase
Press this button to set up humidity and timing time;
Humidity adjusting the order of 30% to 35% – 40% – 45% – 50% – 55% – 60% -– 65% – 70% – 75% – 80% – 30%;
Time set to 00, press this key, display 00 and blink, then press this key again every time, from 01-02-03-...... to 24.
Decrease
Press this button to lower humidity setting and timing time;
Humidity adjusting the order of 30% to 80% – 75% – 70% – 65% – 60% – 55% – 50% – 45% – 40% – 35% – 30%;
Time set to 00, press this key, display 00 and blink, and then press this key again every time, from 24-23-22-...... to 00.
OPERATION

19
CHILDLOCK LOCK
When the machine is turned on, press the button for 3 seconds to open/close the child lock function. When the button is
turned on, the indicator light of the child lock is on. The indicator light of child lock is o; After the child lock function is
opened, the child lock function will be cancelled automatically as long as the shutdown or power failure occurs.
SLEEP / RESET
Press this button to switch the sleep function on or o.
In “Sleep”mode, the unit operates at a low fan speed with a fixed target humidity of 60%.
When the mode is active, the indicators for the sleep function, the child lock and power are dimmed. All other displays
go out.
Activate the timer before you start the sleep function and the dehumidifier will switch o after the set runtime.
If the filter indicator lights up , the dust filter must be checked/cleaned/replaced.
Then the display can be reset by pressing and holding (at least 3 seconds) the Sleep / Reset button.
OPERATION

eng 20
INFORMATION ON THE APP “MYCOND”
The “Mycond” app is available for android and iOS.
Scan the corresponding QR code to get directly to the download.
INFORMATION ON HOW TO USE THE APP
This appliance allows you to operate the appliance via your home net-work. A prerequisite is a permanent Wi-Fi
connection to your router and the free app “Mycond”.
We recommend disconnecting the appliance from the power supply when you are away from home to prevent
unintentional switching on while you are on the road!
Commissioning via the App
1. Install the “Mycond” app. Create a user account.
2. Activate the Wi-Fi function in the settings of your appliance.
3. Place the appliance at a distance of about 5 meters to your router.
4. As long as the power is turned on, the Wi-Fi indicator flashes slowly. After 3 minutes, the status will be canceled if there
is no network configuration, and the indicator light is o. If you need to re-connect the Wi-Fi, long press the “timer”
button for 5 second to start the network configuration, the Wi-Fi indicator flashes slowly.
5. When Wi-Fi indicator flashes slowly, select “Add Device” – “Dehumidifier”, and follow the instructions on the
display.
6. Once the appliance has been successfully connected, the Wi-Fi lamp lights up. Now you can operate the appliance using
the app.
7. Press and hold the Timer button for about 5 seconds, the appliance disconnect, the Wi-Fi lamp lights o.
OPERATION