Mycond TIBO Smart 12 User manual

user's manual
■
посібник
користувача
■
руководство
пользователя
1
AIR DEHUMIDIFIER
TIBO Smart 12


USER’S MANUAL
3
TIBO Smart 12
AIR DEHUMIDIFIER

eng 4
USER’S MANUAL
PLEASE KEEP THIS MANUAL FOR FURTHER REFERENCE!
Thank you for selecting our super quality dehumidifier. Please be sure to read this manual
carefully before using it. If you have any questions, please contact the professional service for
help. Keep the manual for further reference.
The dehumidifier will remove excess moisture from the air, creating a comfortable
environment for your home and oce. Its compact design allows you to easily move it to any
room.

5
CONTENTS
PRECAUTIONS ■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■ 6
APPEARANCE ■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■ 12
SPECIFICATIONS ■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■ 14
OPERATION ■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■ 15
MAINTENANCE ■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■ 22
TROUBLESHOOTING■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■ 26
DECOMMISSIONING ■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■■ 28

eng 6
PRECAUTIONS
Read the following notices carefully before operating this dehumidifier.
The warnings and notices must be observed effectively to ensure the safety of the operation.
1. This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or
mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning
use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance.
Cleaning and user maintenance shall not be made by children without supervision.
2. The unit is designed only for use with R-290 (propane) gas as the designated refrigerant.
3. The refrigerant loop is sealed. Only a qualified technician should attempt to service!
4. Do not discharge the refrigerant into the atmosphere.
5. R-290 (propane) is flammable and heavier than air.
6. It collects first in low areas but can be circulated by the fans.
7. If propane gas is present or even suspected, do not allow untrained personnel to attempt to find the cause.
8. The propane gas used in the unit has no odor.
9. The lack of smell does not indicate a lack of escaped gas.
10. If a leak is detected, immediately evacuate all persons from the store, ventilate the room and contact the local fire
department to advise them that a propane leak has occurred.
11. Do not let any persons back into the room until the qualified service technician has arrived and that technician advises
that it is safe to return to the store.
12. No open flames, cigarettes or other possible sources of ignition should be used inside or in the vicinity of the units.
13. Component parts are designed for propane and non-incentive and non-sparking. Component parts shall only be
replaced with identical repair parts.
14. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons
in order to avoid a hazard.
15. The appliance shall be disconnected from its power source during maintenance.

7
PRECAUTIONS
16. Always operate the unit from a power source of equal voltage, frequency and rating as indicated on the product
identification plate.
17. Always use a power outlet that is grounded.
18. Unplug the power cord when cleaning or when not in use.
19. Do not operate with wet hands. Prevent water from spilling onto the unit.
20. Do not immerse or expose the unit to rain, moisture or any other liquid.
21. Do not leave the unit running unattended. Do not tilt or turn over the unit.
22. Do not unplug while the unit is operating.
23. Do not unplug by pulling on the power cord.
24. Do not use an extension cord or an adapter plug.
25. Do not put objects on the unit.
26. Do not climb or sit on the unit.
27. Do not insert fingers or other objects into the air outlet.
28. Do not touch the air inlet or the aluminum fins of the unit.
20. Do not operate the unit if it is dropped, damaged or showing signs of product malfunction.
30. Do not clean the appliance with any chemicals.
31. Ensure the unit is far away from fire, inflammable, or explosive objects.
32. The unit shall be installed in accordance with national wiring regulations.
33. Do not use means to accelerate the defrosting process or to clean, other than those recommended by the manufacture.
34. The appliance shall be stored in a room without continuously operation sources (for example: open flames, an operating
gas appliance or an operating electric heater).
35. The appliance shall be stored so as to prevent mechanical damage from occurring.
36. Do not piece or burn, even after use.
37. Be aware that refrigerants may not contain an odour.
38. Pipe-work shall be protected from physical damage and shall not be installed in an unventilated space, if that space is
smaller than 4m².

eng 8
39. Compliance with national gas regulations shall be observed.
40. Keep any required ventilation openings clear of obstruction.
41. The appliance shall be stored in a well-ventilated area where the room size corresponds to the room area as specified
for operation.
Any person who is involved with working on or breaking into a refrigerant circuit should hold a current valid certificate from
an industry-accredited assessment authority, which authorizes their competence to handle refrigerants safely in accordance
with an industry, recognized assessment specification.
Servicing shall only be performed as recommended by the equipment manufacturer. Maintenance and repair requiring
the assistance of other skilled personnel shall be carried out under the supervision of the person competent in the use of
flammable refrigerants.
If you don’t understand something or need help, please contact the dealer services.
PRECAUTIONS

9
SAFETY PRECAUTIONS ON SERVICING
Please follow these warnings when to undertake the following when servicing a dehumidifier with R290.
Checks to the area
Prior to beginning work on systems containing flammable refrigerants, safety checks are necessary to ensure that the risk
of ignition is minimized. For repair to the refrigerating system, the following precautions shall be complied with prior to
conducting work on the system.
Work procedure
Work shall be undertaken under a controlled procedure so as to minimize the risk of a flammable gas or vapor being present
while the work is being performed.
General work area
All maintenance staff and others working in the local area shall be instructed on the nature of work being carried out. Work
in confined spaces shall be avoided. The area around the workspace shall be sectioned off. Ensure that the conditions within
the area have been made safe by control of flammable material.
Checking for presence of refrigerant
The area shall be checked with an appropriate refrigerant detector prior to and during work, to ensure the technician is
aware of potentially flammable atmospheres. Ensure that the leak detection equipment being used is suitable for use with
flammable refrigerants, i.e. no sparking, adequately sealed or intrinsically safe.
PRECAUTIONS

eng 10
Presence of fire extinguisher
If any hot work is to be conducted on the refrigeration equipment or any associated parts, appropriate fire extinguishing
equipment shall be available to hand. Have a dry powder or CO2fire extinguisher adjacent to the charging area.
No ignition sources
No person carrying out work in relation to a refrigeration system which involves exposing any pipe work that contains
or has contained flammable refrigerant shall use any sources of ignition in such a manner that it may lead to the risk of
fire or explosion. All possible ignition sources, including cigarette smoking, should be kept sufficiently far away from the
site of installation, repairing, removing and disposal, during which flammable refrigerant can possibly be released to the
surrounding space. Prior to work taking place, the area around the equipment is to be surveyed to make sure that there are
no flammable hazards or ignition risks. “No Smoking” signs shall be displayed.
Ventilated area
Ensure that the area is in the open or that it is adequately ventilated before breaking into the system or conducting any hot
work. A degree of ventilation shall continue during the period that the work is carried out. The ventilation should safely
disperse any released refrigerant and preferably expel it externally into the atmosphere.
Checks to the refrigeration equipment
Where electrical components are being changed, they shall be fit for the purpose and to the correct specification. At all
times the manufacturer’s maintenance and service guidelines shall be followed. If in doubt consult the manufacturer’s
technical department for assistance.
PRECAUTIONS

11
The following checks shall be applied to installations using flammable refrigerants:
The charge size is in accordance with the room size within which the refrigerant containing parts are installed;
The ventilation machinery and outlets are operating adequately and are not obstructed;
If an indirect refrigerating circuit is being used, the secondary circuit shall be checked for the presence of refrigerant;
Marking to the equipment continues to be visible and legible. Markings and signs that are illegible shall be corrected;
Refrigeration pipe or components are installed in a position where they are unlikely to be exposed to any substance which
may corrode refrigerant containing components, unless the components are constructed of materials which are inherently
resistant to being corroded or are suitably protected against being so corroded.
Checks to electrical devices
Repair and maintenance to electrical components shall include initial safety checks and component inspection procedures.
If a fault exists that could compromise safety, then no electrical supply shall be connected to the circuit until it is
satisfactorily dealt with. If the fault cannot be corrected immediately but it is necessary to continue operation, an adequate
temporary solution shall be used. This shall be reported to the owner of the equipment so all parties are advised.
Initial safety checks shall include:
those capacitors are discharged: this shall be done in a safe manner to avoid possibility of sparking;
that there no live electrical components and wiring are exposed while charging, recovering or purging the system;
that there is continuity of earth bonding.
PRECAUTIONS

eng 12
APPEARANCE
3 color digital display
Right panel
Front panel
Control panel
Caster

13
APPEARANCE
Air outlet
Left panel
Power cord
Back shellHandle
Water tank
Continuous drainage
Air inlet withair filter

eng 14
SPECIFICATIONS
MODELL TIBO SMART 12
Dehumification Capacity 12L/D(30 °C, RH 80%)
Rated Voltage AC220-240V/50Hz
Max .rated Input Power Current 200W/1.2A (30 °C, RH 80%)
Noise ≤38 dB(A)
Water Tank Capacity 2.0 L
Maximum Refrigerant Charge R290 / 50 g
Net weight 10 kg
Maximum Design Pressure High Side: 3.2MPa
Low Side:0.7MPa
Airflow 120 m3/hr
Minimum Room size 4 m (Floor area)
Dimension 255х220х445 mm
Note: The above technical specifications are subject to change without notice.

15
Note: The manufacture may provide other suitable
example or may provide additional information about the
refrigerant odour.
LOCATION
1. Place the unit on a firm, level surface in an area with at least 30cm of free space around it to allow for proper air
circulation.
2. Never install the unit where it could be subject to:
Heat sources such as radiators, heat registers, stoves or other products that products that produce heat.
In an area where oil or water may be splashed
Direct sunlight
Mechanical vibration or shock
Excessive dust
Lack of ventilation, such as cabinet or bookcase
Uneven surface
WARNING
Install the unit in rooms which exceed 4 m².
Do not install the unit in a place where inflammable gas may leak.
30 сm
30 сm
OPERATION

eng 16
OPERATING THE DEVICE SAFELY
Check the device after unpacking for any damages or scratches on it.
Operate this unit in an ambient temperature from 5°C to 35°C.
Do not use in the outdoors. This dehumidifier is intended for indoor residential applications only.
Do not operate in close proximity to walls, curtains, or other objects that may block inlet and outlet.
Keep the air inlet and outlet free of obstacles.
Adjusting the wind deflector in the upward direction prior to start up.
If tipped more than 45°, allow the unit to set upright for at least 24 hours before start up.
Keep doors and windows close for better energy saving.
Do not operate or store the unit in direct sunlight or rain.
It is normal for air outlet to feel warm to touch after continuous operation on hot days.
Empty the water tank before moving the device.
Make sure the Water tank is correctly fitted otherwise the unit will not operate properly.
The dehumidifier starts up in the mode selected when the unit was last used.
The dehumidifier starts dehumidifying if the room humidity is 3% higher than the selected humidity.
There is a protective 3-minutes time delay of the compressor. Wait 3 minutes for the dehumidifier to resume
dehumidification.
OPERATION

17
OPERATION
POWER
After switching on the power, all the indicators and the screen will be on for 1 second and then o. After a buzzer, the power
indicator will be on and the machine will be in standby mode.
Press this button, the machine starts to run, the machine initial humidity is 60%RH, default automatic mode and high wind
operation.
Press this key again, the machine will stop running, and the fan will be closed.

eng 18
OPERATION
MODE
Auto mode: Auto mode - continuously drying mode-sleeping mode cycle, press once to switch the mode from one to
another, the corresponding indicator lights up.
wWhen environmental humidity ≥ set humidity +3%, the fan starts working and compressor starts working after 3
seconds.
When environmental humidity ≤ set humidity -3%, the compressor stops working and and the fan delay shutdown.
Both fan speed and humidity can be adjusted under auto mode.
Continuously drying mode: The machine continues to run, but the humidity can not be adjusted.
Sleeping mode: ДTouch the sleep button, the button lights up and start the sleep function. After no operation in 10
seconds, all indicators turns dark gradually and the wind speed is automatically switched from high to low. Touch any
button to wake up the indicator. Touch sleep button again to exit the sleep mode.
n sleep mode, the fault code is not displayed, the wind speed is not adjustable, and the humidity is adjustable.
HUMIDITY
In automatic mode or sleep mode, you can operate this key to adjust the set humidity: every time you press the set
humidity increase by 5%, according to the cycle of 30%-80%.
Long press this key to query the current room temperature, double eight lights display the current room temperature 5
seconds after the automatic return to display the current humidity. If this key is pressed for a long time, it will be display the
ambient temperature.

19
OPERATION
TIMER
Press this key to set the timer function of 0-24 hours. The interval is 1 hour. Each time you press this button, the value
increased 1 hours and then the corresponding timing value is displayed on the screen. The setting value is “00” to cancel the
timer function. The indicator turns out.
After the timer is set and completed, the timer LED is on during the timing period. After the timing is over, the timer LED turns
o automatically.
In the running state, set the time to turn o the machine;
in the standby state, set the time to turn on the machine.
SPEED
The wind speed can only be adjusted in the automatic mode. Press this key to switch the high and low wind speed. The
corresponding wind speed indicator lights up.
LOCK
Long press this key to open the child lock function. The child lock indicator light is on. All the keys are locked and cannot be
operated. Press this button again, the indicator light will go out, and the button will be restored.
Open the child lock function, as long as the shutdown or power o will automatically cancel the child lock function.
3 COLOR DIGITAL DISPLAY
Ambient Humidity<45%, the light show Blue
45≤Ambient Humidity ≤65%, the light show Green
Ambient Humidity >65%, the light show Red
If the LED display E0, E2, CL, CH, LO, HI, the light will show red.

eng 20
INFORMATION ON THE APP “MYCOND”
The “Mycond” app is available for android and iOS.
Scan the corresponding QR code to get directly to the download.
INFORMATION ON HOW TO USE THE APP
This appliance allows you to operate the appliance via your home net-work. A prerequisite is a permanent Wi-Fi
connection to your router and the free app “Mycond”.
We recommend disconnecting the appliance from the power supply when you are away from home to prevent
unintentional switching on while you are on the road!
Commissioning via the App
1. Install the “Mycond” app. Create a user account.
2. Activate the Wi-Fi function in the settings of your appliance.
3. Place the appliance at a distance of about 5 meters to your router.
4. As long as the power is turned on, the Wi-Fi indicator flashes slowly. After 3 minutes, the status will be canceled if there
is no network configuration, and the indicator light is o. If you need to re-connect the Wi-Fi, long press the “timer”
button for 5 second to start the network configuration, the Wi-Fi indicator flashes slowly.
5. When Wi-Fi indicator flashes slowly, select “Add Device” – “Dehumidifier”, and follow the instructions on the
display.
6. Once the appliance has been successfully connected, the Wi-Fi lamp lights up. Now you can operate the appliance using
the app.
7. Press and hold the Timer button for about 5 seconds, the appliance disconnect, the Wi-Fi lamp lights o.
OPERATION
Table of contents
Languages:
Other Mycond Dehumidifier manuals

Mycond
Mycond ABS 7A Service manual

Mycond
Mycond YUGO 12 User manual

Mycond
Mycond ROOMER Eco 25 User manual

Mycond
Mycond WORKER 50 User manual

Mycond
Mycond ROOMER Smart 25 User manual

Mycond
Mycond GIANT Eco 70 User manual

Mycond
Mycond BERG 25 User manual

Mycond
Mycond ROOMER 12 User manual

Mycond
Mycond ROOMER Smart 12 User manual

Mycond
Mycond YUGO Smart 16 User manual