Nabco GYRO TECH GT-1175 User manual
1 of 56
Model GT1175 Standard Slide Doors Installaon Manual
**with U30 Control**
P/N C-00105 Rev 5-17-19
Nabco Entrances Inc. S82 W18717 Gemini Drive Muskego, Wisconsin 53150
Phone: (877) 622-2694 Fax: (888) 679-3319 www.nabcoentrances.com
NABCO hours of Operaon: Monday to Friday 8:00 a.m.- 4:30 p.m. (Central Time)
Associated Manuals Part Numbers: U30 Microprocessor Control Setup and Programming Manual P/N C-00203 Model
GT1175 Electrical Installation Manual **with U30 Microprocessor Control** P/N C-00198
Automatic Sliding Door Owners Manual (P/N C-00109) for Decal Installation
NABCO Price Book P/N 16-9244-30 (for Sensors, Switches, and Accessories)
• Turn OFF all power to the Automatic Door if a Safety System is not working.
• Instruct the Owner to keep all power turned OFF until corrective action can be achieved
by a NABCO trained technician. Failure to follow these practices may result in serious
consequences.
• NEVER leave a Door operating without all Safety detection systems operational.
WARNING
Table of Contents
4
4
5
SECTION 3.1: To the Installer .......................................................................5
SECTION 3.2: Objecve ...........................................................................5
5
SECTION 4.1: Types of Units .......................................................................5
SECTION 4.2: Header Conguraon .................................................................5
SECTION 4.3: Header Components ..................................................................6
SECTION 4.4: Remove the Header Cover .............................................................6
7
7
8
SECTION 7.1: Secure Transom Vercals to Header .....................................................8
SECTION 7.2: Install the Glass Stops .................................................................9
SECTION 7.3: Secure Header and Transom to Pocketed Jamb Tubes ......................................11
SECTION 7.4: Assemble Door Frame ................................................................11
SECTION 7.5: Install the Tie Rods ..................................................................12
SECTION 8.1: Anchor Placements ..................................................................14
SECTION 8.2: Complete the Tie Rod Installaon (For Transom Units only) .................................14
2 of 56
GT1175 Standard Slide Doors Installaon Manual; with U30 Control www.NabcoEntrances.com
P/N C-00105 Rev 5-17-19
SECTION 10.1: Install the Surface Threshold .........................................................15
SECTION 10.2: Install the Recessed Threshold ........................................................17
SECTION 11.1: Install the Boom Pivot .............................................................18
SECTION 11.2: Parally Install the Limit Arm .........................................................18
SECTION 11.3: Install the Full Open Sidelite onto the Upper Pivot and Boom Pivot ........................18
SECTION 11.4: Complete Installaon of the Limit Arm .................................................19
SECTION 11.5: Adjust the Ball Detents ..............................................................19
SECTION 12.1: Secure the Fixed Sidelite to the Door Frame .............................................20
SECTION 12.2: Install the Boom Guide Assembly ....................................................21
SECTION 12.3: Install the Floor Bracket .............................................................21
SECTION 13.1: Secure Slide Door to Belt Clips ........................................................22
SECTION 13.2: Install Boom Guides ...............................................................23
SECTION 13.3: Adjust Rollers ......................................................................23
SECTION 13.4: Adjust the Interlocks ................................................................24
SECTION 14.1: Threshold Maintenance .............................................................25
SECTION 16.1: Door Panels .......................................................................26
SECTION 16.2: Door Frame .......................................................................26
SECTION 17.1: Door Panel ........................................................................27
SECTION 17.2: Complete the Transom Installaon ....................................................28
SECTION 17.3: Complete the 1/4” Glass Stop Flush Glazing .............................................28
SECTION 17.4: Dust Protector Hoods (Clean Room Oponal) ...........................................29
SECTION 17.5: Aluminum Hood ...................................................................29
SECTION 17.6: Stainless Steel Hood (Header) ........................................................29
3 of 56
www.NabcoEntrances.com GT1175StandardSlideDoorsInstallaonManual;withU30Control
Rev.5-17-19 P/NC-00105
SECTION 18.1: Balance Weight of Door Panel with Nose Caster .........................................30
SECTION 18.2: Adjust the Breakout Magnet .........................................................30
SECTION 18.3: Adjust Preload .....................................................................30
SECTION 18.4: Adjust Horizontal Posion of Carrier ...................................................31
SECTION 18.5: Adjust the Ball Plunger ..............................................................32
47
48
4 of 56
GT1175 Standard Slide Doors Installaon Manual; with U30 Control www.NabcoEntrances.com
P/N C-00105 Rev 5-17-19
Warning labels are universal and used to alert an individual of potential harm to one’s self or to others. The following warning
high
some
may result in a minor injury
Note: Indicates important informaon that provides further instrucon.
DANGER
WARNING
CAUTION
WARNINGWARNINGWARNING
WARNING
DANGER
DANGER
CAUTION
CAUTION
5 of 56
www.NabcoEntrances.com GT1175StandardSlideDoorsInstallaonManual;withU30Control
Rev.5-17-19 P/NC-00105
The purpose of this manual is to familiarize the installer and purchaser with the proper installation and operation of this
system. It is essential that this equipment be properly installed and operational before the door is used by the public. It is the
installer’s responsibility to inspect the operation of the entrance system to be sure it complies with any applicable standards.
Instruct the building owners and operator on the essentials of the operation of the door and this device. The owner should
follow these instructions to determine whether the door is operating properly and should immediately call for service if there
This manual offers step by step instructions.
X
•
•
X
•
•
X
Figure 1
DN 0537
Power Supply
U30 Microprocessor Control
DS150 Operator
5
6
HEADER
>POM<
0
7
1
2
3
4
5
6
7
8
9
10
11
12
DS-150ＮＡ
（24-11327）
MADEIN JAPAN
GYROTECH
12
13
14
15
16
Sequential Activation
SQ
Auxiliary Output (Open-Collector)
OUT
5Amax.(0-20V), 3.2Amax.(20-30V)
30V(42.4Vpeak)max.
Contact Output (Class2 Load only)
Common
N/C
N/O
OUT.A
OUT.B
OUT.C
12VDC-(Common)
7
FUNCTION [SLIDING DOOR]
SYMBOL
No.
Reduced Opening Switch
11
10
9
8
7
6
5
4
3
2
1
Breakout Detector
Sidelite Presence Sensor
Exterior Activation
BA
62
SLS
M1
H
M0
Holding Beam
Interior Activation
12VDC-(Common)
12VDC+
6B
9DC12V
7
61
Mode Switch (see Mode SW Usage shown left)
HANDY TERMINAL･6P
RELATED DEVICES･16P
To protect against risk of fire
or electric shock,use only the
certified NABCO power supply.
WARNING
No.
MOTOR･12P
ERROR
POWER
BA
62
H
6B
61
INDICATORS
POWER･2P
Do not disassemble the control box.
There are no user serviceable parts
inside.
To maintain warranty,repairsmust be
made by authorized NABCO facilities.
CAUTION
Adjustments to the door can only be made
with the NABCO Handy Terminal.
Mode SW Usage
Gnd
GndGnd
Open
Open
Open
Gnd
Open
M0
M1
MODE
TWO WAY
ONE WAY
NIGHT
HOLD OPEN
248901-
Microprocessor Controller
20VAC 50/60Hz
GYRO TECH
CAUTION
6 of 56
GT1175 Standard Slide Doors Installaon Manual; with U30 Control www.NabcoEntrances.com
P/N C-00105 Rev 5-17-19
X
DN 0536
5
6
Power Supply
HEADER
DS150 Operator
>POM<
0
7
1
2
3
4
5
6
7
8
9
10
11
12
DS-150ＮＡ
（24-11327）
MADEIN JAPAN
GYROTECH
U30 Microprocessor Control
12
13
14
15
16
Sequential Activation
SQ
Auxiliary Output (Open-Collector)
OUT
5Amax.(0-20V), 3.2Amax.(20-30V)
30V(42.4Vpeak)max.
Contact Output (Class2 Load only)
Common
N/C
N/O
OUT.A
OUT.B
OUT.C
12VDC-(Common)
7
FUNCTION [SLIDING DOOR]
SYMBOL
No.
Reduced Opening Switch
11
10
9
8
7
6
5
4
3
2
1
Breakout Detector
Sidelite Presence Sensor
Exterior Activation
BA
62
SLS
M1
H
M0
Holding Beam
Interior Activation
12VDC-(Common)
12VDC+
6B
9DC12V
7
61
Mode Switch (see Mode SW Usage shown left)
HANDY TERMINAL･6P
RELATED DEVICES･16P
To protect against risk of fire
or electric shock,use only the
certified NABCO power supply.
WARNING
No.
MOTOR･12P
ERROR
POWER
BA
62
H
6B
61
INDICATORS
POWER･2P
Do not disassemble the control box.
There are no user serviceable parts
inside.
To maintain warranty,repairsmust be
made by authorized NABCO facilities.
CAUTION
Adjustments to the door can only be made
with the NABCO Handy Terminal.
Mode SW Usage
Gnd
GndGnd
Open
Open
Open
Gnd
Open
M0
M1
MODE
TWO WAY
ONE WAY
NIGHT
HOLD OPEN
248901-
Microprocessor Controller
20VAC 50/60Hz
GYRO TECH
X
DN 0535
5
6
Power Supply
HEADER
DS150 Operator
>POM<
0
7
1
2
3
4
5
6
7
8
9
10
11
12
DS-150ＮＡ
（24-11327）
MADEIN JAPAN
GYROTECH
U30 Microprocessor Control
12
13
14
15
16
Sequential Activation
SQ
Auxiliary Output (Open-Collector)
OUT
5Amax.(0-20V), 3.2Amax.(20-30V)
30V(42.4Vpeak)max.
Contact Output (Class2 Load only)
Common
N/C
N/O
OUT.A
OUT.B
OUT.C
12VDC-(Common)
7
FUNCTION [SLIDING DOOR]
SYMBOL
No.
Reduced Opening Switch
11
10
9
8
7
6
5
4
3
2
1
Breakout Detector
Sidelite Presence Sensor
Exterior Activation
BA
62
SLS
M1
H
M0
Holding Beam
Interior Activation
12VDC-(Common)
12VDC+
6B
9DC12V
7
61
Mode Switch (see Mode SW Usage shown left)
HANDY TERMINAL･6P
RELATED DEVICES･16P
To protect against risk of fire
or electric shock,use only the
certified NABCO power supply.
WARNING
No.
MOTOR･12P
ERROR
POWER
BA
62
H
6B
61
INDICATORS
POWER･2P
Do not disassemble the control box.
There are no user serviceable parts
inside.
To maintain warranty,repairsmust be
made by authorized NABCO facilities.
CAUTION
Adjustments to the door can only be made
with the NABCO Handy Terminal.
Mode SW Usage
Gnd
GndGnd
Open
Open
Open
Gnd
Open
M0
M1
MODE
TWO WAY
ONE WAY
NIGHT
HOLD OPEN
248901-
Microprocessor Controller
20VAC 50/60Hz
GYRO TECH
>POM<
07
1
2
3
4
5
6
7
8
9
10
11
12
DS-150
(2
4-11327)
12
13
14
15
16
Sequenal Acvaon
SQ
Auxiliary Output (Open-Collector)
OUT
5Amax.(0-20V), 3.2Amax.(20-30V)
30V(42.4Vpeak)max
Contact Output (Class2 Load only)
Common
N/C
N/O
OUT.A
OUT.B
OUT.C
12VDC-(Common)
7
FUNCTION [SLIDING DOOR
SYMBOL
No.
Reduced Opening Switch
11
10
9
8
7
6
5
4
3
2
1
Breakout Detector
Sidelite Presence Sensor
Exterior Acvaon
BA
62
SLS
M1
H
M0
Holding Beam
Interior Acvaon
12VDC-(Common)
12VDC+
6B
9DC12V
7
61
Mode Switch (see Mode SW Usage shown le)
HANDY TERMINAL 6P
RELATED DEVICE S16P
To protect against risk offire
or electric shock,use only the
cerfied NABCO power supply.
WARNING
No.
MOTOR12P
ERROR
POWER
BA
62
H
6B
61
INDICATO RS
POWER2P
Do not disassemble the control box
There are no user serviceable parts
inside.
To maintain warranty,repairs must be
made by authorized NABCO facilies.
CAUTION
Adjustments to the door can only be made
with the NABCO Handy Terminal.
Mode SW Usage
Gnd
GndGnd
Open
Open
Open
Gnd
Open
M0
M1
MODE
TWO WAY
ONE WAY
NIGHT
HOLD OPE N
248901-
Microprocessor Controller
20VAC 50/60Hz
GYRO T EC H
GYROTECH
DN 0369
①②③④⑤⑥⑦
⑨
⑧
⑩
1Power Cut O Switch N/A 6Belt Clip Assembly A-00759
2 DS 150/U30 Power Supply A-00717 7 Timing Belt 3/4” wide M-01491
3 Handy Terminal Harness M-01517 8Idler Assembly A-00042
4 U30 Microprocessor Control V-00020 9An Rise Roller A-00163
5DS 150 Operator M-00395 10 Hanger Roller A-00162
1. Remove (2) 8-32x0.625L Flat head screws. Remove Header Cover by liing it up and then pulling it out.
2. Unplug the Sensor (if equipped). Remove Parts boxes and/or Parts bags from inside Header.
DN 0393
Cover in
Closed Posi on
Li UP to
Pull out
8-32 x 5/8”
Phillips Head Screw
Swing
UP
to Open
Figure 2
Figure 3
7 of 56
www.NabcoEntrances.com GT1175StandardSlideDoorsInstallaonManual;withU30Control
Rev.5-17-19 P/NC-00105
1. Ensure the Rough Opening is correct size.
XPACKAGE WIDTH +1/4 INCH ON EACH SIDE
XPACKAGE HEIGHT +1/4 INCH
Note: Make allowances for le or other exisng materials that may change the oor height.
2. Ensure the oor is level across the enre opening. If used, check recessed threshold across the door opening.
Jamb Tube
1/2”
1-3/4”
Recess Threshold 4-1/2”
R.O. WIDTH
R.O.
HEIGHT
90.0° 90.0°
1/4”
(6mm)
FINISHED FLOOR 1/4”
(6mm)
1/4”
(6mm)
DN 1740
Recessed
Threshold
Floor
Figure 4
DN 0768
SINGLE BIPART
1. Posion Jamb Tubes on either side of Header according to the instrucon scker located on each Jamb Tube, showing
proper locaon and orientaon.
a. Ensure the removable cover side of Header is facing up.
2. Orientate the Frame in relaon to the building:
X
X
Figure 5
DN 0394
FIXED SIDELITE UNITS:
ACCESS COVER TYPICALLY
FACES THE EXTERIOR
Door
Opening
Door
Opening
FULL OPEN UNITS:
ACCESS COVER TYPICALLY
FACES THE INTERIOR
NOTE: Header diagrams shown with Access Cover removed.
8 of 56
GT1175 Standard Slide Doors Installaon Manual; with U30 Control www.NabcoEntrances.com
P/N C-00105 Rev 5-17-19
3. Secure the Header to each Jamb Tube with (6) 1/4-20 x .75 Whizlock screws.
a. If installed correctly there will be a 1/8 inch gap between the boom of Jamb Tubes and the at surface.
Slick
Jamb Tube
DN 1349
Header
1/4-20 x .75” Whizlock Screw
1/8” gap
Flat Surface
Figure 6
DN 0688
Fixed or Breakout Panel
Slide Door
Header
Transom Horizontal
Transom Vercal
Glass or Panel
Jamb Tube
Figure 7
X
X
used to divide glass or panels.
X
X
1. Place the Header on a at surface. Align the Transom clips to the pre-drilled holes on top.
2. Secure Transom Clips to Header with 10 x 1-3/4 inch Phillips Pan Head screws.
a. Please refer to the orientaon scker located on the Header for proper locaon and orientaon.
DN 0419
Top of Header
Orientaon Scker Vercal Transom Clip
10x1-3/4”
Pan Head Screw
HEADER COVER SIDE
Header Cover
3. Obtain Transom Vercals.
4. Secure (1) Transom Vercal to each Transom Clip with 1/4-20 x 1” Flat Head screws.
5. Secure the Transom Horizontal onto the Transom Vercals with #8 x 1 inch Pan Head screw.
Figure 8
9 of 56
www.NabcoEntrances.com GT1175StandardSlideDoorsInstallaonManual;withU30Control
Rev.5-17-19 P/NC-00105
DN 2144
Horizontal Transom
#8 x 1”
Pan Head Screw
Top of Header
1/4-20 x 1”
Phillips Head Screw
Vercal
Transom
Figure 9
Note: Each Glass Stop is precut at the NABCO Factory according to placement and height of the Transom Vercal.
Note: Glass Panels can be installed before or aer the Door Frame is secured to the rough opening.
DN 2134
Example Shown:
Fixed Sidelite
1/4” Glass
Base Glass Stop
Exterior
1” Tall, 3/8” Glass
1” Tall, 5/8” Glass
1” Tall, 7/8” Glass
1” Tall, 1/4” Glass
1” Tall, 1/2” Glass
1” Tall, 3/4” Glass
1” Tall, 1” Glass
Header
Example Shown:
Full Open
1” Glass
Base Glass Stop
Exterior
Header
Figure 10
1. Go to the top of Header. Snap-In the Base Glass Stops between each Transom Vercal.
a. Ensure the tall back of Base Glass Stops face the Exterior side of building.
DN 2156
Measure full width of each Base Glass Stop
Transom Vercal
Top of Header
Base Glass Stop
Transom Horizontal
Figure 11
10 of 56
GT1175 Standard Slide Doors Installaon Manual; with U30 Control www.NabcoEntrances.com
P/N C-00105 Rev 5-17-19
1. Go underneath the Transom Horizontal. Snap-In Base Glass Stops between the Transom Vercals.
a. Ensure the tall back of Base Glass Stops face the Exterior side of building.
2. Go to the Transom Vercal. Snap-In Base Glass Stops between the Transom Horizontal and Base Glass Stops located on top
of the Header.
a. Transom Vercals should be installed just above the Base Glass Stop installed on the Header.
DN 2153
1” Tall, 1/4” Glass
1” Tall, 3/8” Glass
1” Tall, 5/8” Glass
1” Tall, 7/8” Glass
1” Tall, 1/2” Glass
1” Tall, 3/4” Glass
1” Tall, 1” Glass
Pocketed Jamb Tube
Transom Horizontal
Transom Ver cal
1” Snap-In
Base Glass Stop
1” Snap-In
Base Glass Stop
EXTERIOR
EXTERIOR
Example Shown for Transom Ver cals and Jamb Tubes
-looking down- onto Header
Snap-In
Base Glass Stop
Snap-In
Base Glass Stop Top of
Header
Figure 12
DN 2148
Measure full width of each Base Glass Stop
Measure between the Top
of Glass Stop and Boom of
Transom Horizontal to cut
Vinyl Strips
Transom Horizontal
Transom Vercal
End of Header
Base Glass Stop
End of Header
Figure 13
1. Measure between the Boom of the Transom Horizontal and the Top of the Base Glass Stop located on the Header. Cut
strips of Vinyl to that length.
2. Measure the full width of each Base Glass Stop located on the Transom Horizontal. Cut strips of Vinyl to that length.
3. On the same side as the Glass Stop, roll or press Vinyl Strips into each Transom Pocket.
a. Using a Roller, or keeping the vinyl wet with plain or soapy water, can make vinyl installaon easier.
4. The other side of Vinyl Strips are installed aer the Glass Panel has been put in place. Please see “SECTION 17.1: Complete
the Transom Installaon”.
11 of 56
www.NabcoEntrances.com GT1175StandardSlideDoorsInstallaonManual;withU30Control
Rev.5-17-19 P/NC-00105
Vinyl
Vinyl
Base Glass Stop
Vinyl
DN 2146
Figure 14
Note: 1175 Slide Door Units installed with a Transom are shipped with Pocket Jamb Tubes only.
Pocketed
Jamb Tube
DN 0949
1/4-20 x .75”
Whizlock Screw
1/8” gap
Flat Surface
Figure 15
1. Place the Header between the Pocket Jamb Tubes so the removable cover side is facing up. Ensure the Frame is sll
orientated in relaon to the building.
2. Secure the Header to each Jamb Tube with (6) 1/4-20 x .75 Whizlock screws. If installed correctly there will be a 1/8 inch gap
between the boom of Jamb Tubes and the at surface.
Figure 16
DN 0661
Door
Opening
Door
Opening
FIXED SIDELITE UNITS:
ACCESS COVER TYPICALLY
FACES THE EXTERIOR
FULL OPEN UNITS:
ACCESS COVER TYPICALLY
FACES THE INTERIOR
NOTE: Header diagrams shown with Access Cover removed.
1. Posion Jamb Tubes on either side of Header according to the instrucon scker located on each Jamb Tube, showing
proper locaon and orientaon. Ensure the removable cover side of Header is facing up.
2. Orientate the Frame in relaon to the building:
X
X
12 of 56
GT1175 Standard Slide Doors Installaon Manual; with U30 Control www.NabcoEntrances.com
P/N C-00105 Rev 5-17-19
Note: Tie Rods are provided for Transom Units as required by NABCO Engineering.
1. Li to posion the assembled Frame into the rough opening.
2. Shim and Plumb Jamb Tubes in both planes to ensure the rough opening allows a 1/4 inch clearance.
3. Shim and plumb the Transom Horizontal at the top to ensure the rough opening allows a 1/4 inch clearance.
Figure 17
1/4” Shim and plumb
for proper clearance
DN 1348
Jamb Tube
Horizontal Transom
1/4”
4. Go to the side of Header that is closest to the Exterior side of Door Opening,
5. Mark the exact locaon of each Transom Vercal by drawing a horizontal line (the full width of the Transom Vercal); along
the outside edge of the Transom Horizontal; onto the ceiling of the Rough Opening.
a. Do not draw the line wider than the Transom Vercal. It is recommended to use a level for this step.
6. From the center of each Horizontal line, measure 1 inch deep (towards the interior side of building). Mark a Vercal line
onto the ceiling of the Rough Opening. It is recommended to use a level for this step.
Mark Line
Ceiling
DN 0411
Measure 1” deep from
center of Horizontal Line
1”
3/8-16 Concrete Anchor
hole end of 1” mark
Exterior side of
Door Opening
Figure 18
7. Carefully remove the Door Frame from the Rough Opening. Set aside.
8. At the end of each Vercal Line mark, drill (1) 3/8-16 Concrete Anchor hole into the ceiling of the Rough Opening.
9. Obtain all Tie Rods. (1) Tie Rod Parts box is shipped for each Transom Vercal.
10. Snap the Back Plate out from each Transom Vercal for easy access to the Tie Rod.
11. Transom Vercals are pocketed with (2) channels. Determine which channel is closest to the Exterior side of Door Opening.
12. Insert (1) Tie Rod into that channel.
Channel closet to
Exterior side of Door Opening
DN 1350
Figure 19
13. Go to the top of Header. Insert each Tie Rod down into the 1 inch, pre-drilled hole.
14. Once the Tie Rod is through the Header, loosely aach (1) Backing Plate, (1) 3/8 inch Washer, (1) 3/8 inch Lock Washer and
(1) 3/8-16 Hex Nut (in that order) to the boom of the Tie Rod.
a. The length of each Tie Rod equals the distance between the top of the Header, and the top of the Transom Horizontal,
plus 2-5/8 inches.
13 of 56
www.NabcoEntrances.com GT1175StandardSlideDoorsInstallaonManual;withU30Control
Rev.5-17-19 P/NC-00105
DN 1152
Transom Ver cal Tie Rod
3/4” Min
Backing Plate, 3/8” Flat Washer,
3/8” Lock Washer, and 3/8-16 Hex Nuts
Concrete Anchor Securely fasten Tie Rod to Anchor
with 3/4” minimum thread
engagement into building structure
Leg of
Roller Track
Header Cover
Horizontal Transom
Transom
Ver cal
Back Plate
Channel
Figure 20
15. Allow each Tie Rod to rest on the Roller Track “Leg” within the Header.
a. The Tie Rod must remain inside the Transom Vercal unl the Frame is fully secured into the Rough Opening.
b. Tie Rod Installaon is completed aer the Frame is installed.
Figure 21
Transom Horizontal
DN 0404
Vercal Transom
(Mullion)
Tie Rod
Top of
Header
Boom of Header
1. Li to posion the assembled Frame into the rough opening.
a. To prevent electrical interference for the 120 Vac Line, always route 120 Vac Power through the Header Endcap that is
opposite to the controller and motor/operator.
b. Please refer to “Model GT 1175 Electrical Installaon Manual”; P/N C-00198 for detailed informaon.
2. Shim and Plumb Jamb Tubes in both planes to ensure the rough opening allows a 1/4 inch clearance. Shim and plumb the
Header or the Transom Horizontal at the top to ensure the rough opening allows a 1/4 inch clearance.
Figure 22
1/4” Shim and plumb
for proper clearance
DN 0760
Jamb Tube
Header
1/4” Shim and plumb
for proper clearance
Horizontal
Transom
1/4”
14 of 56
GT1175 Standard Slide Doors Installaon Manual; with U30 Control www.NabcoEntrances.com
P/N C-00105 Rev 5-17-19
X
X
X
Figure 23
DN 0767
Y
48”
max
YY
YY
36”
max
48”
max
Y
SLIDE DOOR SLIDE DOOR w/TRANSOM
YY
36”
max
48”
max
Y
Y
48”
max
YY
Note: It is recommended to countersink holes as required to ush the surface.
Note: It is recommended to drill tap threads for 1/4 inch anchors in a steel or aluminum structure.
Note: Do not overghten anchors to prevent deforming Jamb Tubes.
Use 1/4 inch diameter anchors with a minimum of 3 per Jamb Tube, maximum is 48 inches on center. Drill 1/4 inch diameter holes
in the face of Jamb and then countersink each hole.
DN 0418
SLICK JAMB
1/4” Anchor 1/4” Anchor Hole(s)
POCKETED JAMB / VERTICAL TRANSOM
1/4” Anchor 1/4” Anchor Hole(s)
Figure 24
X
X
To prevent Header sag, use 1/4 inch diameter anchors or 3/8 inch threaded rods, with a maximum 48 inches on center. First
anchor maximum is 36 inches from each end of the Header. Drill 1/4 inch diameter holes inside the top of Header.
1. Aer the Frame has been installed, slide each Tie Rod up the Channel into each 3/8-16 Anchor located in the ceiling.
a. The 3/8-16 Anchor is used to securely fasten the Frame.
2. Go to the boom of each Tie Rod. Tighten the 3/8-16 Hex Nut and 3/8 inch Lock Washer to secure the Backing Plate.
3. Snap the Back Plate back into each Transom Vercal.
a. It may be necessary to use a rubber mallet to slightly tap the Back Plate into place.
b. Protect the surface of the Back Plate before hing it with a rubber mallet.
15 of 56
www.NabcoEntrances.com GT1175StandardSlideDoorsInstallaonManual;withU30Control
Rev.5-17-19 P/NC-00105
DN 1002
Female Pin Housing
Jamb Tube
Wire Access Hole
Header Plate
Wire Access Hole
Key Switch
Rocker Switch
Male Pin Housing
Female Pin Wiring
Blue
Green
Orange
3
4
5
Red
Orange/White 2
1
Figure 25
1. Go inside the Header. Locate the Pin wiring that is aached to the U30 Microprocessor Control, Main Harness.
2. Draw Pin wiring through a hole located at the side of Header and Jamb Tube. Connue to route wiring down the Jamb Tube.
3. Pull the Pin Wiring out, through the cut out.
4. Obtain (1) loose 5 Circuit Pin Housing from the Parts Box. Insert each Pin into the 5 Circuit Pin Housing accordingly:
a. 1 = Red, 2 = Orange/White, 3 = Blue, 4 = Green, 5 = Orange
5. Obtain (1) Switch Assembly and (2) 10-32 x 1/2 inch Phillips Head Screws from the Parts Box.
6. Connect the Switch Harness from the back of the Switch Assembly to the Main Harness. Place extra wiring back inside the
Jamb Tube.
7. Insert the Switch Assembly into the Cut Out.
8. Secure the Switch Assembly to the Jamb Tube with (2) 10-32 x 1/2 inch Phillips Head Screws.
Note: Thresholds are factory cut to be the same width as the door opening. However, extending the Threshold across the enre
door opening is oponal. To order addional track, please contact customer service at (877) 622-2694.
Figure 26
DN 0087
7”
SURFACE TRACK
RECESSED TRACK
4 ”
Bumpers
Bumpers
X
X
FOR JAMB-TO-JAMB TUBE APPLICATIONS, SKIP TO STEP (3)
1. Locate (2) screw splines on the exposed side(s) of the Threshold.
2. Secure (1) Threshold End Cap to the screw spline(s) with (2) 6 x 3/8 inch Phillips Head screws.
a. If the Threshold End Cap can not be properly secured with the screws provided, use a 1/8 inch diameter drill bit to
make the screw spline bigger.
16 of 56
GT1175 Standard Slide Doors Installaon Manual; with U30 Control www.NabcoEntrances.com
P/N C-00105 Rev 5-17-19
Figure 27
DN 0091
Screw Spline
End Cap
6 x 3/8”
Phillips Head Screw
Threshold
Screw Spline
3. On the same side of Door Frame where the Sidelite will be installed, snap a chalk line on the oor from Jamb to Jamb.
Figure 28
DN 1027
Jamb Tube
Jamb Tube
Chalk Line
Chalk Line
EXTERIOR
FULL OPEN FIXED SIDELITE
4. Lay down the Threshold so the Bumper Channels are on same side of Slide Doors.
5. Ensure the Threshold is centered to Jamb Tubes, and full length is ush with the chalk line.
DN 1369
Jamb Tube
Example Shown: Bi-Part Slide Door
Bumpers
Filler Inserts
BUMPERS
(Used to Cushion Boom Guide Prongs)
FILLER INSERTS
(Used to Fill In areas
Boom Guide does not slide within)
Figure 29
6. Go to the Header on the Sidelite Side of Door Frame.
7. Plumb the Floor Track by hanging the Plumb Bob from the Header (Sidelite Side). There should be a 1/8 inch overhang.
Jamb
Tube
4-1/2”
DN 0090
6-1/2”
Header
Ramp
Slide Door
4-1/2”
Threshold
1/8” gap between Plumb Line and edge of Track
Figure 30
8. Do not permanently install the Surface Threshold unl the Slide Doors are completely installed.
17 of 56
www.NabcoEntrances.com GT1175StandardSlideDoorsInstallaonManual;withU30Control
Rev.5-17-19 P/NC-00105
Figure 31
Floor Surface Track
1/2”
DN 0761
1. On both the Exterior and the Interior side of Door Frame, snap a chalk line on the oor from Jamb to Jamb.
DN 2117
Jamb Tube
Chalk Line
Figure 32
2. Create a channel that is the full width of Jamb Tubes, and 1/2 inch deep.
3. Lay down the Threshold so the Bumper Channels are on same side of Slide Doors.
4. Center the Threshold inside the channel so the full length is ush with the chalk line.
5. Ensure the channel is plumb, square, and 1/2 inch deep throughout. Failure to do so may cause the Slide door to malfuncon.
6. Go to each end of Threshold. Mark (1) drill hole approximately 4” from each edge. Connue to mark remaining drill holes to be
evenly spaced.
Figure 33
Drill Screw Holes in Metal Strip
DN 1047
Example Shown:
Full Open Slide Door
7. With a 1/4 inch masonry drill bit, drill through the Threshold and into the oor no less than 1-1/2 inch deep.
8. Do not permanently install the Surface Threshold unl the Slide Doors are completely installed.
Figure 34 Secure Threshold to Flat Surface
DN 2114
Fasteners not provide by NABCO
Metal Strip
RECESSED THRESHOLD
DN 0762
Swing Sidelite
FULL OPEN
Figure 35
18 of 56
GT1175 Standard Slide Doors Installaon Manual; with U30 Control www.NabcoEntrances.com
P/N C-00105 Rev 5-17-19
1. Go to the boom of the Pivot Jamb Tube. Insert the Boom Pivot into the hole.
2. Secure the Boom Pivot to the Pivot Jamb Tube with (1) 1/4-20 x 1/2 inch Phillips Head screw.
3. Go to the screw hole located in front of the Barrel. Secure the Floor Pivot to the Threshold with (1) 1/4-20 x 1/2 inch Phillips
Head Screw.
4. Insert (1) 1/4 x 2-3/4 inch Phillips Head Screw inside the Barrel. Tighten.
5. Cap the Barrel with (1) Bushing.
Figure 36
DN 1045
1/4-20 x 1/2”
Phillips Head Screw
Boom Pivot
1/4-20 x 1/2”
Phillips Head Screw
1/4 x 2-3/4”
Tapcon Screw
Bushing
1. Slide (1) .255 ID x .900 OD x .125 THK Nylon Washer onto (1) 1/4-20 x 1 inch Phillips Head Screw.
2. Go underneath the Limit Arm. Insert the Washer and Screw up into the screw hole.
3. Go to the pre-drilled screw hole located at the boom of Header (on the Pivot Side of Sidelite).
4. Secure the Limit Arm to the Header by ghtening the Screw.
a. Loosely ghten (just enough to keep the Screw assembly from falling out of the hole).
b. Limit Arm installaon is completed aer the Swing Sidelite is fully installed.
Figure 37
DN 0771
Limit Arm
Limit Arm Wheel 1/4-20 x 1”
Phillips Head Screw
.255 x .900 x .125 THK
Nylon Washer
Boom of Header
Pivot Hole
1. Locate the Boom Pivot inside the Pivot Sle (at the boom). Insert the Boom Pivot into the Floor Pivot Barrel.
Figure 38
DN 1046
Barrel
Boom Pivot
2. Go to the Top Pivot that is preinstalled inside the Pivot Sle. Push the Top Pivot down by pressing on the Spring Pin.
3. Align the Top Pivot with the Pivot Hole located at the boom of Header.
4. Release the Spring Pin to allow the Top Pivot to snap up into the hole. Ensure the Top Pivot fully engages the hole.
a. If necessary, use a athead screwdriver to li up on the Spring pin unl the Pivot Pin is fully seated within the hole.
b. Ensure not to pinch Cable Wiring.
19 of 56
www.NabcoEntrances.com GT1175StandardSlideDoorsInstallaonManual;withU30Control
Rev.5-17-19 P/NC-00105
DN 2160
Top Pivot
Cable Wiring from
Main Harness (Inside Header)
Break Out
Direcon
Pivot Sle
Spring Pin
Hole
Spring Pin
Figure 39
1. Swing open the Swing Sidelite 90 degrees. Align and then rest the Limit Arm inside the Top Rail.
2. Open the Swing Sidelite all the way. Tighten (1) 1/4-20 x 1 inch Phillips Head screw to secure the Limit Arm to the Header.
Note: Breakout resistance for Ball Detents must meet ANSI Standard A156.10 or Local Codes.
1. Go to the top of the Strike Sle. With a 15/16” Open End wrench, loosen the Nut to raise or lower the Ball Detent so it has
light contact with the Boom of Header.
2. Open and close the Swing Door several mes to score the surface on the Boom of Header locate and mark where the Score
intersects the center groove.
3. With a 1/4 inch drill bit, drill a screw hole through the Boom of Header. Countersink the screw hole 3/8 inch x 82°.
Figure 40
DN 0764 90°
Drilled and Countersunk Hole
Score Mark
Ball Dentent
Nut
Top of Strike Sle
4. Go to the boom of the Strike Sle. With a 15/16” Open End wrench, loosen the Nut to raise or lower the Ball Detent so it
has light contact with the Threshold.
5. Open and close the Swing Door several mes to score the surface on the Threshold. Locate and mark where the Score
intersects the center groove.
6. With a 1/4 inch diameter drill bit, drill a hole through the Threshold (Just deep enough for the Ball Dentent to t within).
Countersink the screw hole to be 1/4 inch x 82°.
Figure 41
DN 0765
Nut
Boom Rail
90°
Drilled and
Countersunk Hole
Score Mark
Ball Dentent
20 of 56
GT1175 Standard Slide Doors Installaon Manual; with U30 Control www.NabcoEntrances.com
P/N C-00105 Rev 5-17-19
7. Close and then break open the Swing door to test t for both Ball Detents.
a. To adjust the t, increase the size of the hole and countersink.
b. Do Not over-drill the hole. If hole is overdrilled the Threshold will need to be replaced.
c. For addional travel remove the Ball Detent Bracket to lower or raise the Ball Detent.
DN 1703
Fixed Sidelite
Slide Door
Figure 42
1. Locate (2) Cut Outs on the side of the Pivot Sle. Align and then slide the Fixed Sidelite unl (2) Mounng Brackets
(preinstalled on the Pivot Jamb Tube) can be seated inside each Cut Out.
2. Slide the Fixed Sidelite towards the Interior of the Building unl both Mounng Brackets bu up against the inside wall of
the Pivot Sle.
Figure 43
DN 0863
Jamb Tube Moun ng Bracket
Header Moun ng Bracket
(Inside Ver cal Mullion)
1/4-20 x 1/2”
Flat Head Screw
1/4-20 x 1/2”
FlatHead Screw
Jamb Tube
Moun ng Bracket
Cutout Clearance
3. Locate (1) cut out at the top of Strike Sle. Align and then slide the Fixed Sidelite unl (1) mounng bracket (preinstalled
under the Boom Lip of Header) can be seated inside the Cut Out.
Figure 44
DN 0862
Cut Out
Mounng BracketStrike Sle
4. Snap a chalk line between Jamb Tubes in front of Sidelite Panel. If the Sidelite Panel is ush to the chalk line, it is square.
5. Secure the Fixed Sidelite Panel to all (3) Mounng Brackets with 1/4-20 x 1/2 inch Flat Head Screws.
Figure 45
DN 0624
Chalk Line
Jamb Tube
Fixed Panel
Jamb Tube
Other manuals for GYRO TECH GT-1175
5
Table of contents
Other Nabco Door Opening System manuals
Nabco
Nabco GYRO TECH GT-1175 User manual
Nabco
Nabco GT-1400 User manual
Nabco
Nabco Acusensor 3 User manual
Nabco
Nabco Opus Control User manual
Nabco
Nabco GT20 8300 User manual
Nabco
Nabco GYRO TECH GT-1175 Owner's manual
Nabco
Nabco ICU 2400 User manual
Nabco
Nabco GT20 Owner's manual
Nabco
Nabco C-00139 User manual
Nabco
Nabco GT-710 User manual
Popular Door Opening System manuals by other brands
Roger Technology
Roger Technology H85/TDS Instruction and warnings for the installer
SUGATSUNE
SUGATSUNE LAMP FD80-H installation manual
GEZE
GEZE TSA 160 Planning Document
Lock
Lock L5241AL installation instructions
Ellard
Ellard Spider Installation guides
Dormakaba
Dormakaba GSR-EMR XEA BG Mounting instructions
Manusa
Manusa Op. Visio L1H installation manual
Nice
Nice SPA2 Instructions and warnings for installation and use
Assa Abloy
Assa Abloy Norton 5700 Series installation instructions
Blasi
Blasi C 127 SU S operating instructions
Entrematic
Entrematic Ditec TOPSB installation manual
Label
Label NEXT 75 user manual
