Nabco GYRO TECH GT-1175 User manual

S82 W18717 Gemini Drive
Muskego, Wisconsin 53150
Phone: [phone]
Fax: [phone]
www.nabcoentrances.com
Part #C-00121
Rev. 8/25/16
WARNING
• Turn OFF all power to the Automac Door if a Safety System is not working.
• Instruct the Owner to keep all power turned OFF unl correcve acon can be achieved by a NABCO
trained technician. Failure to follow these pracces may result in serious consequences.
• NEVER leave a Door operang without all Safety detecon systems operaonal.
Model GT 1175

**with U30 Microprocessor Controller**

120 VAC
LABEL ON U30 CONTROL
A
C115V ± 10%
50 / 60 Hz
BLACK (HOT)
SCREW TO HEADER
WHITE (COMMON)
GROUND LUG
MADE IN JAPAN
（24-11327）
DS-150ＮＡ
GYROTECH
ON/OFF
POWER
SWITCH
TRANSFORMER
A
M
P
5
TB1
NOISE
FILTER
TB2
T1
S1
ZNR2
ZNR1
AUXILIARY 120 VAC
POWER WIRES
(THESE WIRES NORMALLY
COILED AND TIED UP)
MOTOR/OPERATOR P/N 24-11327
ACTIVATION SIGNAL
OUTPUT SIGNAL
OFF
OFF
ON
ON
FULLY CLOSED
OPENING
FULL OPEN
CLOSING
FULLY CLOSED
OUTPUT: 0 = ELECTRIC STRIKE OUTPUT
OUTPUT TIMER
0 =(DO NOT USE)
1 =(DO NOT USE)
2 =(DO NOT USE)
3 =ELECTRIC STRIKE FUNCTION
U30 ELECTRIC STRIKE OUTPUT SIGNAL
HANDY TERMINAL: AUX OUTPUT = 0, OUTPUT TIMER = 3, ROCKER SWITCH SETTING: ONE WAY OR NIGHT MODE
OUTPUT TIMER
1.0 SEC
3 SEC
U30 CONTROL P/N 24-8901-30
POWER SUPPLY P/N 14-11741
GROUND HARNESS
P/N 14-11872
POWER SUPPLY HARNESS
P/N 14-11874
VIOLET
GRAY (OUT A)
TERMINAL ON U30 MAIN HARNESS
P/N 24-11877
WIRING FOR ELECTRIC LOCK ONLY SHOWN
FAIL SECURE LOCK ASSY.
P. N. 22-10522-03
FAIL
SECURE
VIO
GRY
WHT
BLK
1
6
110V
20VAC 50/60Hz
Microprocessor Controller
248901-
GYRO TECH HOLD OPEN
NIGHT
ONE WAY
TWO WAY
MODEM1M0
Open
Gnd
Open
Open
Open
GndGnd
Gnd
Mode SW Usage
Adjustments to the door can only be made
with the NABCO Handy Terminal.
CAUTION
To maintain warranty,repairs must be
made by authorized NABCO facilities.
Do not disassemble the control box.
There are no user serviceable parts
inside.
POWER･2P
INDICATORS
61
6B
H
62
BA
POWER
ERROR
MOTOR･12P
No.
WARNING
To protect against risk of fire
or electric shock,use only the
certified NABCO power supply.
RELATED DEVICES･16P
HANDY TERMINAL･6P
Mode Switch (see Mode SW Usage shown left)
61
7
6B
12VDC+
12VDC-(Common)
Interior Activation
Holding Beam
M0
H
M1
SLS
62
BA
Exterior Activation
Sidelite Presence Sensor
Breakout Detector
1
2
3
4
5
6
7
8
9
10
11
Reduced Opening Switch
No.
FUNCTION [SLIDING DOOR]
712VDC-(Common)
OUT.C
OUT.B
OUT.AN/O
N/C
Common
Contact Output (Class2 Load only)
30V(42.4Vpeak)max.
5Amax.(0-20V), 3.2Amax.(20-30V)
OUT
Auxiliary Output (Open-Collector)
SQ
Sequential Activation
16
15
14
13
12
12VDC-COMMON
Auxiliary Output (Open-Collector)
Sequential Activation
5Amax.(0-20V), 3.2Amax.(20-30V)
30V(42.4Vpeak)max.
Contact Output (Class2 Load only)
FUNCTION [SLIDING DOOR]
REDUCED OPENING SWITCH
Breakout Detector
Sidelite Presence Sensor
Exterior Activation
HOLDING BEAM
INTERIOR ACTIVATION
12VDC-(COMMON)
12VDC+
Mode Switch (see Mode SW Usage shown left)
Common
N/C
N/O
SQ
OUT
OUT.A
OUT.B
OUT.C
7
SYMBOL
BA
62
SLS
M1
H
M0
6B
9DC12V
7
61
12
13
14
15
16
No.
11
10
9
8
7
6
5
4
3
2
1
RELATED DEVICES - 16P
1
2
3
4
5
6
7
8
9
10
11
16
15
14
13
12
1
2
3
4
5
6
7
8
9
10
11
16
15
14
13
12
SYMBOL
9DC12V

THIS PAGE IS INTENTIONALLY LEFT BLANK

Rev. 8-25-16 Part #C-00121
www.NabcoEntrances.com ElectricalInstallaonManualU-30“D”Control
i
Table of Contents
Warning Labels ....................................................................iii
General Safety Recommendaons ....................................................iv
.......................................................
Secon 1a: TotheInstaller ...........................................................1-5
Secon 1b: Objecve................................................................1-5
 ............................................
Secon 2a: AbouttheU30MicroprocessorControl .......................................2-6
Secon 2b: ElectricalSpecicaons ....................................................2-6
Secon 2c: OutputPowerGuidelines ..................................................2-7
Secon 2d: HeaderLayout ...........................................................2-7
 ...........................
 ................................. 
Secon 4a: 16PinControllerTerminalBlockAssignments. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-10
Secon 4b: SensorWireConnecons .................................................4-11
Secon 4c: RockerSwitchSengs ....................................................4-12
......................................... 
Secon 5a: (2)Acusensorsand(1)HoldingBeam........................................5-14
Secon 5b: (2)Optexi-OneSensorsand(1)HoldingBeam ................................5-15
Secon 5c: (2)Acusensors,(1)HoldingBeamand(1)BreakoutBeam .......................5-16
Secon 5d: (2)Optexi-OneSensors,(1)HoldingBeamand(1)BreakoutBeam ...............5-17
Secon 5e: (2)IXIO,and(1)HoldingBeam .............................................5-18
Secon 5f: (2)IXIO(1)HoldingBeamand(1)BreakoutBeam..............................5-19
.................................... 
Secon 6a: Wiring(1)HoldingBeam ..................................................6-20
Secon 6b: Wiring(2)HoldingBeams .................................................6-21
Secon 6c: WiringHoldingBeamforBreakout ..........................................6-22

ElectricalInstallaonManualU-30“D”Control www.NabcoEntrances.com
Part #C-00121 Rev. 8-25-16
ii
 ..................................... 
Secon 7a: AdjusttheStrike. ........................................................7-23
Secon 7b: U30withFailSafeElectricLock.............................................7-24
Secon 7c: U30withFailSecureElectricLock...........................................7-25
Secon 7d: U30withMagnecLock ..................................................7-26
 ........................................... 
Secon 8a: U30ConguredforRemoteControlofModes ................................8-27
Secon 8b: SideliteSensors .........................................................8-28
Secon 8c: U30UsingCardReadersorotherSecureAcvaonDevices .....................8-29
Secon 8d: 12VDCRelayAssembly ..................................................8-30
 ........................................ 

Rev. 8-25-16 Part #C-00121
www.NabcoEntrances.com ElectricalInstallaonManualU-30“D”Control
iii
WARNING LABELS
Warning labels are universal and used to alert an individual of potential harm to one’s self or to others. The following warning
labels are listed in a hierarchy order that denes the most potential danger rst, and the least potential danger last. Please refer
to this page in the event that a warning label is displayed within this manual and further denition needs to be explained.
Indicates potentially dangerous situations. Danger is used when there is a hazardous
situation where there is a high probability of severe injury or death.
It should not be considered for property damage unless personal injury risk
is present.
Indicates a hazardous situation which has some probability of severe injury.
It should not be considered for property damage unless personal injury risk
is present.
Indicates a hazardous situation which may result in a minor injury. Caution
should not be used when there is a possibility of serious injury. Caution should
not be considered for property damage accidents unless a personal injury risk
is present.
Notice: Indicates a statement of company policy as the message relates to the personal safety or
protection of property. Notice should not be used when there is a hazardous situation or
personal risk.


DANGER
WARNING
CAUTION

ElectricalInstallaonManualU-30“D”Control www.NabcoEntrances.com
Part #C-00121 Rev. 8-25-16
iv
GENERAL SAFETY RECOMMENDATIONS
Do not install, operate or service this product unless you have read and understand
the General Safety Recommendations, Warning Labels, contained in this manual.
Failure to do so may result in bodily injury, or property damage.
Read, study and understand the installation and operating instructions contained in,
or referenced in this manual before operating. If you do not understand the instruction,
ask a qualied technician. Failure to do so may result in bodily injury, or property
damage and will nullify all warranties.
Disconnect all power to the junction box prior to making any electrical connections.
Failure to do so may result in seriouc personal or fatal injury. When uncertain whether
power supply is disconnected, always verify using a voltmeter.
Do not place nger or uninsulated tools inside the electrical controller. Touching wires
or other parts inside the enclosure may cause electrical shock, serious injury or death.
The Ground wire from the Magnum IV Control 120 VAC Harness, and the Incoming 120
VAC Ground wire must be connected to the Ground screw located within the Swing
door Header.
If the door appears broken or does not seem to work correctly, it should be
immediately removed from service until repairs can be carried out or a qualied
service technician is contacted for corrective action.
Notice: This manual, the owner’s manual and all other associated manuals must be given to and
retained by the purchasing facility or end user.
Notice: Wiring must meet all local, state, federal or other governing agency codes.
Notice: All electrical troublshooting or service must be performed by qualied
electrical technicians and must comply with all applicable governing
agency codes.


WARNINGWARNING
WARNING
DANGER
DANGER
CAUTION
CAUTION

Rev. 8-25-16 Part #C-00121
www.NabcoEntrances.com ElectricalInstallaonManualU-30“D”Control
Scope 1-5

To the Installer
The purpose of this manual is to familiarize the installer and purchaser with the proper
installation and operation of this system. It is essential that this equipment be properly installed
and operational before the door is used by the public. It is the installer’s responsibility to inspect
the operation of the entrance system to be sure it complies with any applicable standards.
Instruct the building owners and operator on the essentials of the operation of the U30
Microprocessor Controller. The owner should follow these instructions to determine whether the
door is operating properly and should immediately call for service if there is any malfunction. All


The U30 Microprocessor Controller is designed to be installed within the Header of the GT-1175
Slide Door systems.
This manual offers step by step instructions.
A pedestrian Door that does not have Its glass sections installed at the Factory
shall specify that the glazing material employed is to comply with the requirement in
UL 325 par.29.5.1:








CAUTION

ElectricalInstallaonManualU-30“D”Control www.NabcoEntrances.com
Part #C-00121 Rev. 8-25-16
2-6 GengStarted


The U30 Microprocessor Control is utilized on all GT-1175 Slide Door systems to control

and reduced opening width.

The U30 Microprocessor Control is also utilized to output power to accessories and/or auxiliary
equipment such as:
►Sensors
►Modules
There are times when the U30 Microprocessor Control is not utilized to output power because
some accessories and/or auxiliary equipment are shipped with it’s own dedicated power supply.






Table 2-1 Sensors
Sensor Part Number Function Power Source Current Consumption
Acusensor 3  Infrared  100mA

  Infrared + Microwave 

100mA
  Infrared  130mA
Table 2-2 Modules
Module Part Number Function Power Source Current Consumption
 14-9710-01   



   50mA

Rev. 8-25-16 Part #C-00121
www.NabcoEntrances.com ElectricalInstallaonManualU-30“D”Control
GengStarted 2-7

current draw from the U30 Microprocessor Control must not exceed 350 mA (0.35 amps)
when outputting power to:
►Sensors
►Modules
►Accessories
►Auxiliary Equipment
If  current draw exceeds 350mA (0.35 amps) the installer must utilize an auxiliary power

The U30 Microprocessor Control and/or the NABCO Power Supply Module Must
Not be used to output power to Magnetic Locks or Electric Strikes.

device. Please refer to the formula shown below:

 
 
 






►
• 
Microprocessor Control. Please see .
►
• 
and the U30 Microprocessor Control. Please see .
►
• 
the U30 Microprocessor Control. Please see .


CAUTION

ElectricalInstallaonManualU-30“D”Control www.NabcoEntrances.com
Part #C-00121 Rev. 8-25-16
2-8 GengStarted
Figure 2-1 
DN 0537 Power Supply
U30 Microprocessor Controller
Operator
Header
>POM<
0
7
1
2
3
4
5
6
7
8
9
10
11
12
GYRO TECH
DS-150ＮＡ
（24-11327）
MADE IN JAPAN
12
13
14
15
16
Sequential Activation
SQ
Auxiliary Output (Open-Collector)
OUT
5Amax.(0-20V), 3.2Amax.(20-30V)
30V(42.4Vpeak)max.
Contact Output (Class2 Load only)
Common
N/C
N/O
OUT.A
OUT.B
OUT.C
12VDC-(Common)
7
FUNCTION [SLIDING DOOR]
SYMBOL No.
Reduced Opening Switch
11
10
9
8
7
6
5
4
3
2
1
Breakout Detector
Sidelite Presence Sensor
Exterior Activation
BA
62
SLS
M1
H
M0
Holding Beam
Interior Activation
12VDC-(Common)
12VDC+
6B
9DC12V
7
61
Mode Switch (see Mode SW Usage shown left)
HANDY TERMINAL･6P
RELATED DEVICES･16P
To protect against risk of fire
or electric shock,use only the
certified NABCO power supply.
WARNING
No.
MOTOR･12P
ERROR
POWER
BA
62
H
6B
61
INDICATORS
POWER･2P
Do not disassemble the control box.
There are no user serviceable parts
inside.
To maintain warranty,repairs must be
made by authorized NABCO facilities.
CAUTION
Adjustments to the door can only be made
with the NABCO Handy Terminal.
Mode SW Usage
Gnd
GndGnd
Open
Open
Open
Gnd
Open
M0
M1
MODE
TWO WAY
ONE WAY
NIGHT
HOLD OPEN
GYRO TECH
248901-
Microprocessor Controller
20VAC 50/60Hz
TRANSFORMER
LABEL
A
M
P
5I
O
TB1
NOISE
FILTER
TB2
T1
S1
ZNR2
ZNR1
DN 0536 Power Supply U30 Microprocessor Controller
Operator
Header
TRANSFORMER
LABEL
A
M
P
5I
O
TB1
NOISE
FILTER
TB2
T1
S1
ZNR2
ZNR1
>POM<
0
7
1
2
3
4
5
6
7
8
9
10
11
12
GYRO TECH
DS-150ＮＡ
（24-11327）
MADE IN JAPAN
12
13
14
15
16
Sequential Activation
SQ
Auxiliary Output (Open-Collector)
OUT
5Amax.(0-20V), 3.2Amax.(20-30V)
30V(42.4Vpeak)max.
Contact Output (Class2 Load only)
Common
N/C
N/O
OUT.A
OUT.B
OUT.C
12VDC-(Common)
7
FUNCTION [SLIDING DOOR]
SYMBOL No.
Reduced Opening Switch
11
10
9
8
7
6
5
4
3
2
1
Breakout Detector
Sidelite Presence Sensor
Exterior Activation
BA
62
SLS
M1
H
M0
Holding Beam
Interior Activation
12VDC-(Common)
12VDC+
6B
9DC12V
7
61
Mode Switch (see Mode SW Usage shown left)
HANDY TERMINAL･6P
RELATED DEVICES･16P
To protect against risk of fire
or electric shock,use only the
certified NABCO power supply.
WARNING
No.
MOTOR･12P
ERROR
POWER
BA
62
H
6B
61
INDICATORS
POWER･2P
Do not disassemble the control box.
There are no user serviceable parts
inside.
To maintain warranty,repairs must be
made by authorized NABCO facilities.
CAUTION
Adjustments to the door can only be made
with the NABCO Handy Terminal.
Mode SW Usage
Gnd
GndGnd
Open
Open
Open
Gnd
Open
M0
M1
MODE
TWO WAY
ONE WAY
NIGHT
HOLD OPEN
GYRO TECH
248901-
Microprocessor Controller
20VAC 50/60Hz
TRANSFORMER
LABEL
A
M
P
5I
O
TB1
NOISE
FILTER
TB2
T1
S1
ZNR2
ZNR1
12
13
14
15
16
Sequential Activation
SQ
Auxiliary Output (Open-Collector)
OUT
5Amax.(0-20V), 3.2Amax.(20-30V)
30V(42.4Vpeak)max.
Contact Output (Class2 Load only)
Common
N/C
N/O
OUT.A
OUT.B
OUT.C
12VDC-(Common)
7
FUNCTION [SLIDING DOOR]
SYMBOL No.
Reduced Opening Switch
11
10
9
8
7
6
5
4
3
2
1
Breakout Detector
Sidelite Presence Sensor
Exterior Activation
BA
62
SLS
M1
H
M0
Holding Beam
Interior Activation
12VDC-(Common)
12VDC+
6B
9DC12V
7
61
Mode Switch (see Mode SW Usage shown left)
HANDY TERMINAL･6P
RELATED DEVICES･16P
To protect against risk of fire
or electric shock,use only the
certified NABCO power supply.
WARNING
No.
MOTOR･12P
ERROR
POWER
BA
62
H
6B
61
INDICATORS
POWER･2P
Do not disassemble the control box.
There are no user serviceable parts
inside.
To maintain warranty,repairs must be
made by authorized NABCO facilities.
CAUTION
Adjustments to the door can only be made
with the NABCO Handy Terminal.
Mode SW Usage
Gnd
GndGnd
Open
Open
Open
Gnd
Open
M0
M1
MODE
TWO WAY
ONE WAY
NIGHT
HOLD OPEN
GYRO TECH
248901-
Microprocessor Controller
20VAC 50/60Hz
>POM<
0
7
1
2
3
4
5
6
7
8
9
10
11
12
GYRO TECH
DS-150ＮＡ
（24-11327）
MADE IN JAPAN
NABCO
DN 0535
Power Supply U30 Microprocessor Controller
Operator
Header
Figure 2-2 
Figure 2-3 

Rev. 8-25-16 Part #C-00121
www.NabcoEntrances.com ElectricalInstallaonManualU-30“D”Control
ConnectIncoming120VACWires 3-9

Disconnect power to the junction box prior to making any electrical connections.
Failure to do so may result in serious personal or fatal injury. When uncertain
whether power supply is disconnected, always verify using a voltmeter.
Notice: Wiring must meet all local, state, federal or other governing agency codes.
Ensure all power is disconnected at the Junction box.



Electric Service Access Hole located at the left or right side of Jamb Tube and Header End Cap.
a. 
Electrical Conduit.
Keep all Incoming 120 VAC wiring separate from low voltage wiring within Header.
Do Not route 120 VAC wires near the U30 Microprocessor Controller and Operater.
Please see 
Power Supply.




Read and understand the “U30 Controller Setup and Programming Manual”
P/N 15-9000 before attempting to power-up the GT-1175 Slide Door. Failure to do
so may result in damage to the Slide door and/or injury to the installer and will
nullify all warranties.
Figure 3-1 
AC 115V ± 10%
50 / 60 Hz
Ground Wire
Auxiliary 120 VAC Power wires
(These wires normally coiled and  ed up)
On/Off
Power Switch
DN 0647
U30 Microprocessor Control
P/N V-00020
0
7
1
2
3
4
5
6
7
8
9
10
11
12
>POM<
NABCO
GYRO TEC H
DS-1500
D24-113270
Nabtesco Corporation
MADEINJAPAN
NABCO
NABCO
CAUTION
!
RELATED DEVICES･16P
12
13
14
15
16
No.
11
10
9
8
7
6
5
4
3
2
1
SYMBOL
H
M0
9DC12V
SQ
OUT
Common
N/C
N/O
OUT.A
OUT.B
OUT.C
7
BA
62
SLS
M1
6B
7
61
Sequential Activation
Auxiliary Output (Open-Collector)
5Amax.(0-20V), 3.2Amax.(20-30V)
30V(42.4Vpeak)max.
Contact Output (Class2 Load only)
12VDC-(Common)
FUNCTION [SLIDING DOOR]
Reduced Opening Switch
Breakout Detector
Sidelite Presence Sensor
Exterior Activation
Holding Beam
Interior Activation
12VDC-(Common)
12VDC+
Mode Switch (see Mode SW Usage shown left)
HANDY TERMINAL･6P
No.
248901-
Microprocessor Controller
Mode SW Usage
Gnd
GndGnd
Open
Open
Open
Gnd
Open
M0
M1
MODE
TWO WAY
ONE WAY
NIGHT
HOLD OPEN
Toprotect against risk of fire
or electric shock,use only the
certified NABCO power supply.
WARNING
MOTOR･12P
ERROR
POWER
BA
62
H
6B
61
INDICATORS
POWER･2P
Do not disassemble the control box.
There are no user serviceable parts
inside.
Tomaintain warranty,repairs must be
made by authorized NABCO facilities.
Adjustments to the door can only be made
with the NABCO Handy Terminal.
20VAC 50/60Hz
GYRO TECH
NABC O
!
!
!
!
TB1
NOISE
FILTER
TB2
T1
S1
PE NL
LOAD
-CIRCUIT-
-BREAKER-
RED INDICATES
POWER IS OFF
PRESS
TO
RESET
POWERSUPPL Y
ASSEMBLY
P/N9418800100
NABCO
14-11741
ENTRANCES,INC.
Power Supply
P/N V-00029
Motor/Operator
P/N M-00395
120 VAC
DANGER
CAUTION
CAUTION
DANGER

ElectricalInstallaonManualU-30“D”Control www.NabcoEntrances.com
Part #C-00121 Rev. 8-25-16
4-10 IdenfyOperangWires







*

Terminal # Symbol Color Description
1  X
• Sensor power source.
• 
7 XCommon terminal
• 
3  XInput terminal
• Interior Activation signal.
• 
4 White XInput terminal
• 
• 
5 H Green XInput terminal
• 
• 
M0  XInput terminal
• 
• 
section within this chapter.
7 M1 
White*
XInput terminal
• 
• 
section within this chapter.
8 

XInput terminal
• Exterior Activation signal.
• 
9 SQ Yellow XInput terminal
• Sequential Activation signal.
• Allows a sequence of signals to open and close Slide door.

Rev. 8-25-16 Part #C-00121
www.NabcoEntrances.com ElectricalInstallaonManualU-30“D”Control
IdenfyOperangWires 4-11
Terminal # Symbol Color Description
10   XInput terminal
• 
• 
• 
happen if:
• 
• 
11 SLS Green/
White*
XInput terminal
• Sidelite Presence Sensor.
• 
  Gray X
• 
• 
• Used as a Switch to:
• 
• 
• Signal a remote computer on the Slide door operation.
13  Gray X
• 
14   X
• 
15  
Yellow*
X
• 
Microprocessor Controller.
• Installer must provide wire for this terminal (not normally utilized).
 7 XCommon terminal
• 

*

** 
Table 4-1 Acusensor
U30 Harness Extension Harness Acusensor Harness
 Common  
  Yellow Green
 Signal Exterior
  Gray 

ElectricalInstallaonManualU-30“D”Control www.NabcoEntrances.com
Part #C-00121 Rev. 8-25-16
4-12 IdenfyOperangWires
Table 4-2 
U30 Harness Extension Harness Optex i-one Harness
 Common  **Gray and White
 Interior Signal Yellow Yellow
 Exterior Signal
  Gray Gray
Table 4-3 
U30 Harness Extension Harness IXIO Harness
 Common  
 Interior Signal Yellow 
 Exterior Signal
  Gray 

 
Rocker Switch
Mode
Key Switch
Mode
Wire
M0
Wire
M1
Wire
HDescription
    -XSensors on Terminal (3) and (8) can not open the door
while door is closed.
XSensors on Terminal (3) and (8) will provide threshold
safety when door is in any position other than closed.
X






activation devices.


    -X
Slide door is held open.
X
Two Way Auto   -XSensors on Terminal (3) and (8) can both open
the door.
X

Rev. 8-25-16 Part #C-00121
www.NabcoEntrances.com ElectricalInstallaonManualU-30“D”Control
IdenfyOperangWires 4-13
Rocker Switch
Mode
Key Switch
Mode
Wire
M0
Wire
M1
Wire
HDescription
 Exit   -XSensor on Terminal (3) can open the door.
• Sensor is normally Interior and used to activate door

XSensor on Terminal (8) can not open the door from the
closed position.
• Sensor is normally Exterior and used to provide
threshold safety only.
• 
occurs from the interior sensor or by a device (such

connected in one of two ways:





activation devices.


  - -  X
open to the full position.
  - -  X


ElectricalInstallaonManualU-30“D”Control www.NabcoEntrances.com
Part #C-00121 Rev. 8-25-16
5-14 WiringDiagrams(SurfaceAppliedSliders)


MOTOR/OPERATOR
P/N 24-11327
Power Harness P/N 14-11874
Grounding Wire
P/N 14-11872
U30 MICROPROCESSOR CONTROL
P/N 24-8901-30
12VDC Commo
n
12 VDC+
12VDC-
(Common)
Holding Beam
R
educed Opening Swit
ch
Mode Swit
ch
Breakout Detector
Sidelite Pr
esence Sensor
Contact Output (Class2 Load only)
30V (42.4V peak) max.
5A max, (0-20V), 3.2A max.
(20-30V)
Auxiliary Output
(Open Collector)
N/O N/C
Common
9DC 12V 7 61 6B H M0 M1 62 SQ BA SLS Out.A Out.B Out.C Out
7
1 2 3 4 5 6 7 8 9
10 11 12 13 14 15 16
Related Devices - 16P
1
2
3
4
5
6
7
8 9
10 11 12
13
14 15
16
White Wire
(Common)
Black Wire (Hot)
RED
BROWN
RED
BLACK
WHITE
GREEN
ORANGE
ORG/WHT
BLK/RED BLK/RED
GRN/WHT
YELLOW
DN 0539
MAIN HARNESS FOR U30 P/N 24-11877
BROWN &RED
(CIRCUIT 1 & 2)
EXTERIOR ACUSENSOR
PT. NO. 14-8902
PT. NO. 14-8902
INTERIOR ACUSENSOR
ON
OFF
NIGHT
TWO WAY
ONE WAY
HOLD OPEN
FULL
OPEN
REDUCED OPEN
BLUE
KEY SWITCH
FOR U30
PN 14-11876
ROCKER SWITCH
FOR U30
PN 14-11875
BACK SIDE OF
ROCKER SWITCH SHOWN
ACUSENSOR EXTENSION HARNESS PN 22-9267-00
ACUSENSOR EXTENSION HARNESS PN 22-9267-00
OPTEX
HOLDING BEAM
CONTROLLER
PT. NO.
PN 14-9710-03
TERM #1
RED
BROWN
RED
BROWN
BLK
RED
GRAY
YELLOW YELLOW
GRAY RED
RED
BLUE
RED
ORANGE
ORG/WHT
ORG/WHT
RED
GREEN
RED
ORANGE
RED
ORG/WHT
BLUE
GREEN
ORANGE
Optex OS-12C
Controller
POWER SUPPLY
P/N 14-11741
AC115V ± 10
%
50 / 60 Hz
Auxiliary 120 VAC Power Wires (These wires are normally
ON/OFF
Power Switch
BLUE
U30 TERMINAL
U30 MICROPROCESSOR CONTROL LABE
L
WHITE
TERM #5
RED
TERM #4
BLUE
BLUE
WHITE
WHITE WHITE
WHITE
MAGNETIC POWER
DOWN SWITCH
P/N 22-9222
WHITE
WHITE
BLUE
TB1
NOISE
FILTER
TB2
T1
S1
PE
N
L
LOAD
-CIRCUIT-
-BREAKER-
RED INDICATES
POWER IS OFF
PRESS
TO
RESET
POWERSUPPLY
ASSEMBLY
P/N9418800100
NABCO
14-11741
ENTRANCES,INC.
0
7
1
2
3
4
5
6
7
8
9
10
11
12
>POM<
NABCO
GYRO TECH
DS-1500
D24-113270
Nabtesco Corporation
MADEINJAPAN
NABCO
NABCO
CAUTION
!
RELATED DEVICES･16P
12 13 14 15 16
No.
11
10
9
8
7
6
5
4
3
2
1
SYMBOL
H
M0
9DC12V
SQ
OU T
Common
N/C N/O
OUT. A OUT. B OUT. C
7
BA
62
SLS
M1
6B
7
61
Sequenal Acvaon
Auxiliary Output (Open-Collector)
5Amax.(0-20V), 3.2Amax.(20-30V
)
30V(42.4Vpeak)max
Contact Output (Class2 Load only)
12VDC-(Common)
FUNCTION (SLIDING DOOR)
Reduced Opening Switch Breakout Detector
Sidelite Presence Sensor
ExteriorAcvaon
Holding Beam
Interior Acvao n
12VDC-(Common) 12VDC +
Mode Switch (see Mode SW Usage shown le)
HANDY TERMINAL 6P
No.
248901-
Microprocessor Controller
Mode SW Usage
Gnd GndGn d
Open
Open Open
Gnd
Open
M0
M1
MODE
TWO WAY
ONE WAY
NIGH T
HOLD OPEN
To protect against risk of Fire
or electric shock,use only the
cerfied NABCO power supply.
WARNING
MOTOR 12P
ERROR
POWER
BA
62
H
6B
61
INDICATORS POWER2P
Do not disassemble the control box.
There are no user serviceable parts
inside.
Tomaintain warranty,repairs must be
made by authorized NABCO facilities.
Adjustments to the door can only be made
with the NABCO Handy Terminal.
20VA C 50/60Hz
GYRO TECH
NABCO
!
!
!
!
U30 TERMINAL
P/N 24-11877
1
2
3
4
5
6
7
8 9
10
11 12
13
14 15
16

Rev. 8-25-16 Part #C-00121
www.NabcoEntrances.com ElectricalInstallaonManualU-30“D”Control
WiringDiagrams(SurfaceAppliedSliders) 5-15

Power Harness
P/N 14-11874
Gr
ounding Wire
P/N 14-11872
12VDC Commo
n
12 VDC+
12VDC-
(Common)
Holding Beam
R
educed Opening Swit
ch
Mode Swit
ch
Break
out Detector
Sidelite Presence Sensor Contact Output
(Class2 Load only)
30V (42.4V peak) max.
5A max, (0-20V), 3.2A max.
(20-30V)
Auxiliary Output
(Open Collector)
N/O N/C
Common
9DC 12V 7 61 6B H M0 M1 62 SQ BA SLS Out.A Out.B Out.C Out
7
1 2 3 4 5 6 7 8 9
10 11 12 13 14 15 16
Related Devices - 16P
1
2
3
4
5
6
7
8 9
10 11 12
13
14 15
16
White Wire
(Common)
Black Wire (Hot)
RED
BROWN
RED
BLACK
WHITE
GREEN
ORANGE
ORG/WHT
BLK/RED BLK/RED
GRN/WHT
YELLOW
DN 0685
MAIN HARNESS FOR U30
P/N 24-11877
EXTERIOR OPTEX I-1
PT. NO. 14-13036
PT. NO. 14-13036
INTERIOR OPTEX I-1
ON
OFF
NIGHT
TWO WAY
ONE WAY
HOLD OPEN
FULL
OPEN
REDUCED OPEN
KEY SWITCH
FOR U30
PN 14-11876
ROCKER SWIT
CH
FOR U30
PN 14-11875
BACK SIDE OF
ROCKER SWIT
CH SHOWN
OPTEX
HARNESS
P/N 12-13018
ACUSENSOR EXTENSION HARNESS
PN 22-9267-00
RED
GRAY
YELLOW
RED
BLUE
RED
ORANGE
ORG/WHT
ORG/WHT
RED
GREEN
RED
ORANGE
RED
ORG/WHT
BLUE
GREEN
ORANGE
AC115V ± 10%
50 / 60 Hz
Auxiliary 120 VAC
Power Wires (These wires are normally
ON/OFF
Power Switch
BLUE
U30 TERMINAL
U30 MICROPROCESSOR CONTROL LABE
L
BROWN &RED
(CIRCUIT 1 & 2)
OPTEX
HOLDING BEAM
CONTROLLER
PT. NO.
PN 14-9710-03
TERM #1
Optex OS-12C
Controller
WHITE
TERM #5
RED
TERM #4
WHITE
GRAY
BLK
GRAY
YELLOW
BROWN
RED
GRAY
YELLOW WHITE
GRAY
BLK
GRAY
RED
YELLOW
BROWN
ACUSENSOR EXTENSION HARNESS
PN 22-9267-00
BLUE
BLUE
BLUE
WHITE
WHITE WHITE
WHITE
MAGNETIC POWER
DOWN SWITCH
P/N 22-9222
WHITE
WHITE
BLUE
MOTOR/OPERATOR
P/N 24-11327
U30 MICROPROCESSOR CONTROL
P/N 24-8901-30
POWER SUPPLY
P/N 14-11741
U30 TERMINAL
P/N 24-11877
TB1
NOISE
FILTER
TB2
T1
S1
PE
N
L
LOAD
-CIRCUIT-
-BREAKER-
RED INDICATES
POWER IS OFF
PRESS
TO
RESET
POWERSUPPLY
ASSEMBLY
P/N9418800100
NABCO
14-11741
ENTRANCES,INC.
0
7
1
2
3
4
5
6
7
8
9
10
11
12
>POM<
NABCO
GYRO TECH
DS-1500
D24-113270
Nabtesco Corporation
MADEINJAPAN
NABCO
NABCO
CAUTION
!
RELATED DEVICES･16P
12 13 14 15 16
No.
11
10
9
8
7
6
5
4
3
2
1
SYMBOL
H
M0
9DC12V
SQ
OU T
Common
N/C N/O
OUT. A OUT. B OUT. C
7
BA
62
SLS
M1
6B
7
61
Sequenal Acvaon
Auxiliary Output (Open-Collector)
5Amax.(0-20V), 3.2Amax.(20-30V
)
30V(42.4Vpeak)max
Contact Output (Class2 Load only)
12VDC-(Common)
FUNCTION (SLIDING DOOR)
Reduced Opening Switch Breakout Detector
Sidelite Presence Sensor
ExteriorAcvaon Holding Beam
Interior Acvaon
12VDC-(Common) 12VDC +
Mode Switch (see Mode SW Usage shown le)
HANDY TERMINAL 6P
No.
248901-
Microprocessor Controller
Mode SW Usage
Gnd GndGn d
Open
Open Open
Gnd
Open
M0
M1
MODE
TWO WAY
ONE WAY
NIGH T
HOLD OPEN
To protect against risk of Fire
or electric shock,use only the
cerfied NABCO power supply.
WARNING
MOTOR 12P
ERROR
POWER
BA
62
H
6B
61
INDICATORS POWER2P
Do not disassemble the control box.
There are no user serviceable parts
inside.
Tomaintain warranty,repairs must be
made by authorized NABCO facilities.
Adjustments to the door can only be made
with the NABCO Handy Terminal.
20VA C 50/60Hz
GYRO TECH
NABCO
!
!
!
!
RED
1
2
3
4
5
6
7
8
9
10
11
12
13
14 15
16

ElectricalInstallaonManualU-30“D”Control www.NabcoEntrances.com
Part #C-00121 Rev. 8-25-16
5-16 WiringDiagrams(SurfaceAppliedSliders)

TB1
NOISE
FILTER
TB2
T1
S1
PE
N
L
LOAD
-CIRCUIT-
-BREAKER-
RED INDICATES
POWER IS OFF
PRESS
TO
RESET
POWERSUPPLY
ASSEMBLY
P/N9418800100
NABCO
14-11741
ENTRANCES,INC.
07
1
2
3
4
5
6
7
8
9
10
11
12
>POM<
NAB CO
GYROTE CH
DS-1500
D24-113270
Nabtesco Corporation
MADEIN JA PAN
NABCO
NABCO
MOTOR/OPERATOR
P/N 24-11327
Power Harness (P/N 14-11874)
Gr
ounding Wi
re
P/
N 14-11872
U30 MICROPROCESSOR CONTROLLER
P/N 24-8901-30
12VDC Commo
n
12 VDC+ 12VDC- (Common)
Interior Ac va on
Holding Beam
Re
duced Opening Switch
Mode Switch
(See Mode SW Usage Shown Le )
Exterior Ac
va on
al Ac va on
Breakout Detector Sidelite Presence Sensor
Contact Output
(Class2 Load only)
30V (42.4V peak) max.
5A max, (0-20V), 3.2A max.
(20-30V)
Auxiliary Output
(Open Collector)
N/O N/C Common
9DC 12V 7
61 6B
H M0 M1 62 SQ
BA SLS Out.A Out.B Out.C Out 7
1 2 3 4 5 6 7 8 9
10 11 12 13 14 15 16
Related Devices - 16P
1
2
3
4
5
6
7
8 9
10 11 12
13
14 15
16
White Wire
(Common)
Black Wire (Hot)
RED
BROWN
RED
BLACK
WHITE
GREEN
ORANGE
ORG/WHT
BLK/RED
WHITE
BLK/RED
GRN/WHT
YELLOW
DN 0541
Main Harness For U30 P/N 24-11877
BROWN &RED
(TERM 1 & 2)
ON
OFF
NIGHT
TWO WAY
ONE WAY
HOLD OPEN
FULL
OPEN
REDUCED OPEN
BLUE
BLUE BLUE
WHITE
WHITE WHITE
WHITE
KEY SWITCH
FOR U30
P/N 14-11876
ROCKER SWITCH
FOR U30
P/N 14-11875
BACK SIDE OF
ROCKER SWITCH SHOWN
ROCKER SWITCH
EXTENSION HARNESS
FOR U30
P/N 14-11884
ACUSENSOR EXTENSION HARNESS P/N 22-9267-00
ACUSENSOR EXTENSION HARNESS P/N 22-9267-00
OPTEX
HOLDING BEAM
CONTROLLER
PT. NO.
P/N 14-9710-03
TERM #1
RED
BROWN
RED
BROWN
BLK
RED
GRAY
YELLOWYELLOW
GRAY RED
RED
BLUE
RED
ORANGE
ORG/WHT
ORG/WHT
RED
GREEN
RED
ORANGE
RED
ORG/WHT
BLUE
GREEN
ORANGE
20VAC 50/60Hz
Microprocessor Controller
248901-
GYRO TECH
HOLD OPEN
NIGHT
ONE WAY
TWO WAY
MODE
M1
M0
Open
Gnd
Open Open
Open
GndG nd
Gnd
Mode SW Usage
Adjustments to the door can only be made with the NABCO Handy Terminal.
CAUTION
To maintain warranty,repairs must be
made by authorized NABCO facilities.
Do not disassemble the control box.
There are no user serviceable parts
inside.
POWER･2P INDICATORS
61
6B
H
62
BA
POWER ERROR
MOTOR･12P
No.
WARNING
To protect against risk of fire
or electric shock,use only the certified NABCO power supply.
RELATED DEVICES･16P
HANDY TERMINAL･6P
Mode Switch (see Mode SW Usage shown left)
61
7 9DC12V 6B
12VDC+
12VDC-(Common)
Interior Activation
Holding Beam
M0
H
M1
SLS 62
BA
Exterior Activation
Sidelite Presence Sensor
Breakout Detector
1
2
3
4
5
6
7 8 9
10
11
Reduced Opening Switch
No.
SYMBOL
FUNCTION [SLIDING DOOR]
7
12VDC-(Common)
OUT.C OUT.B OUT.A
N/O N/C
Common
Contact Output (Class2 Load only)
30V(42.4Vpeak)max.
5Amax.(0-20V), 3.2Amax.(20-30V)
OUT
Auxiliary Output (Open-Collector)
SQ
Sequential Activation
16 15 14 13 12
!
!
!
! !
NABCO
1
2
3
4
5
6
7
8 9
10 11 12
13
14 15
16
POWER SUPPLY
P/N 14-11741
AC115V ± 10%
50 / 60 Hz
Auxiliary 120 VAC Power Wires (These wires are normally coiled and ed up)
ON/OFF
Power Switch
BLUE
MAGNETIC POWER
DOWN SWITCH
P/N 22-9222
OPTEX
BREAKOUT BEAM
CONTROLLER
PT. NO.
P/N 14-9710-03
TERM #1
BROWN &RED
(TERM 1 & 2)
BLUE
(TERM #4)
BLUE
(TERM #3)
WHITE
(TERM #5)
U30 TERMINAL P/N 14-11873
U30 TERMINAL
U30 MICROPROCESSOR CONTROLLER LABE
LRED
(TERM #4)
INTERIOR ACUSENSOR
P/N
EXTERIOR ACUSENSOR
P/N
OPTEX OS-12C
Controller
OPTEX OS-12C
Controller

Rev. 8-25-16 Part #C-00121
www.NabcoEntrances.com ElectricalInstallaonManualU-30“D”Control
WiringDiagrams(SurfaceAppliedSliders) 5-17

TB1
NOISE
FILTER
TB2
T1
S1
PE
N
L
LOAD
-CIRCUIT-
-BREAKER-
RED INDICATES
POWER IS OFF
PRESS
TO
RESET
POWERSUPPLY
ASSEMBLY
P/N9418800100
NABCO
14-11741
ENTRANCES,INC.
0
7
1
2
3
4
5
6
7
8
9
10
11
12
>POM<
NABCO
GYROTECH
DS-1500
D24-113270
NabtescoCorporation
MADEINJAPAN
NABCO
NABCO
MOTOR/OPERATOR
P/N 24-11327
Power Harness P/N 14-11874
Gr
ounding Wire
P/
N 14-11872
U30 MICROPROCESSOR CONTROLLER
P/N 24-8901-30
12VDC Commo
n
12 VDC+ 12VDC- (Common)
Holding Beam
Reduced Opening Switch
Mode Switch
Breakout Detector
Sidelite Presence Sensor Contact Output (Class2 Load only)
30V (42.4V peak) max.
5A
max, (0-20V), 3.
2A max. (20-30V)
Auxiliary Output (Open Collector)
N/O N/C
Common
9DC 12V 7 61 6B H M0 M1 62 SQ BA SLS Out.A Out.B Out.C Out
7
1 2 3 4 5 6 7 8 9
10 11 12 13 14 15 16
Related Devices - 16P
1
2
3
4
5
6
7
8 9
10 11 12
13
14 15
16
White Wi
re
(Common)
Black Wi
re (Hot)
RED
BROWN
RED
BLACK
WHITE
GREEN
ORANGE
ORG/WHT
BLK/RED BLK/RED
GRN/WHT
YELLOW
DN 0542
MAIN HARNESS FOR U30
P/N 24-11877
BROWN &RED
(TERM 1 & 2)
ON
OFF
NIGHT
TWO WAY
ONE WAY
HOLD OPEN
FULL
OPEN
REDUCED OPEN
BLUE
BLUE BLUE
WHITE
WHITE WHITE
WHITE
KEY SWITCH
FOR U30
PN 14-11876
ROCKER SWITCH
FOR U30
PN 14-11875
BACK SIDE OF
ROCKER SWITCH SHOWN
ROCKER SWITCH
EXTENSION HARNESS
FOR U30
PN 14-11884
ACUSENSOR EXTENSION HARNESS PN 22-9267-00
ACUSENSOR EXTENSION HARNESS PN 22-9267-00
OPTEX
HOLDING BEAM
CONTROLLER
PT. NO.
PN 14-9710-03
TERM #1
RED
BROWN
RED
BROWN
BLK
RED
GRAY
YELLOW YELLOW
GRAY RED
RED
BLUE
RED
ORANGE
ORG/WHT
ORG/WHT
RED
GREEN
RED
ORANGE
RED
ORG/WHT
BLUE
GREEN
ORANGE
Optex OS-12C
Controller
20VAC 50/60Hz
Microprocessor Controller
248901-
GYRO TECH
HOLD OPEN
NIGHT
ONE WAY
TWO WAY
MODE
M1
M0
Open
Gnd
Open
Open
Open
GndG nd
Gnd
Mode SW Usage
Adjustments to the door can only be made
with the NABCO Handy Terminal.
CAUTION
To maintain warranty,repairs must be
made by authorized NABCO facilities.
Do not disassemble the control box.
There are no user serviceable parts
inside.
POWER･2P INDICATORS
61
6B
H
62
BA
POWER
ERROR
MOTOR･12P
No.
WARNING
Toprotect against risk of fire
or electric shock,use only the
certified NABCO power supply.
RELATED DEVICES･16P
HANDY TERMINAL･6P
Mode Switch (see Mode SW Usage shown left)
61
7
9DC12V
6B
12VDC+
12VDC-(Common)
Interior Activation
Holding Beam
M0
H
M1
SLS
62
BA
Exterior Activation
Sidelite Presence Sensor
Breakout Detector
1
2
3
4
5
6
7
8
9
10
11
Reduced Opening Switch
No.
SYMBOL
FUNCTION [SLIDING DOOR]
7
12VDC-(Common)
OUT.C OUT.B
OUT.A
N/O N/C
Common
Contact Output (Class2 Load only)
30V(42.4Vpeak)max.
5Amax.(0-20V), 3.2Amax.(20-30V)
OUT
Auxiliary Output (Open-Collector)
SQ
Sequential Activation
16 15 14
13 12
!
!
!
! !
NABCO
1
2
3
4
5
6
7
8 9
10 11 12
13
14 15
16
POWER SUPPLY
P/N 14-11741
AC115V ± 10%
50 / 60 Hz
Auxiliary 120 VAC Power Wires (These wires are
ON/OFF
Power Switch
MAGNETIC POWER
DOWN SWITCH
P/N 22-9222
OPTEX
HARNESS
PN 12-13018
GRAY
YELLOW WHITE
GRAY GRAY GRAY
YELLOW WHITE
INTERIOR OPTEX I-ONE
PN 14-10364-A
EXTERIOR OPTEX I-ONE
PN 14-10364-A
BLUE
OPTEX
BREAKOUT BEAM
CONTROLLER
PT. NO.
PN 14-9710-03
TERM #1
Optex OS-12C
Controller
BROWN &RED
(TERM 1 & 2)
BLUE
(TERM #4)
BLUE
(TERM #3)
U30 TERMINAL P/N 14-11873
U30 TERMINALU30 MICROPROCESSOR CONTROLLER LABEL
WHITE
TERM #5
RED
TERM #4
WHITE
WHITE
BLUE

ElectricalInstallaonManualU-30“D”Control www.NabcoEntrances.com
Part #C-00121 Rev. 8-25-16
5-18 WiringDiagrams(SurfaceAppliedSliders)

TB1
NOISE
FILTER
TB2
T1
S1
PE
N
L
LOAD
-CIRCUIT-
-BREAKER-
RED INDICATES
POWER IS OFF
PRESS
TO
RESET
POWERSUPPLY
ASSEMBLY
P/N9418800100
NABCO
14-11741
ENTRANCES,INC.
0
7
1
2
3
4
5
6
7
8
9
10
11
12
>POM<
NABCO
GYROTECH
DS-1500
D24-113270
NabtescoCorporation
MADEINJAPAN
NABCO
NABCO
MOTOR/OPERATOR
P/N 24-11327
Power Harness P/N 14-11874
Gr
ounding Wire
P/
N 14-11872
U30 MICROPROCESSOR CONTROLLER
P/N 24-8901-30
12VDC Commo
n
12 VDC+ 12VDC- (Common)
Holding Beam Reduced Opening Switch
Mode Switch
Breakout Detector
Sidelite Presence Sensor Contact Output (Class2 Load only)
30V (42.4V peak) max.
5A
max, (0-20V), 3.
2A max. (20-30V)
Auxiliary Output (Open Collector)
N/O N/C
Common
9DC 12V
7 61 6B H M0 M1 62 SQ BA SLS Out.A Out.B Out.C Out
7
1 2 3 4 5 6 7 8 9
10 11 12 13 14 15 16
Related Devices - 16P
1
2
3
4
5
6
7
8 9
10 11 12
13
14 15
16
White Wire (Common)
Black Wi
re (Hot)
RED
BROWN
RED
BLACK
WHITE
GREEN
ORANGE
ORG/WHT
BLK/RED BLK/RED
GRN/WHT
YELLOW
DN 0554
MAIN HARNESS FOR U30
P/N 24-11877
BROWN &RED
(c IRcUIt 1 & 2)
ON
OFF
NIGHT
TWO WAY
ONE WAY
HOLD OPEN
FULL
OPEN
REDUCED OPEN
BLUE
BLUE BLUE
WHITE
WHITE WHITE
WHITE
KEY SWITCH
FOR U30
PN 14-11876
ROCKERSWITCH
FOR U30
PN 14-11875
BACK SIDE OF
ROCKER SWITCH SHOWN
ROCKER SWITCH
EXTENSION HARNESS
FOR U30
PN 14-11884
ACUSENSOR EXTENSION HARNESS PN 22-9267-00
ACUSENSOR EXTENSION HARNESS PN 22-9267-00
OPTEX
HOLDING BEAM
CONTROLLER
PT. NO.
PN 14-9710-03
TERM #1
RED
BROWN
RED
BROWN
BLK
RED
GRAY
YELLOW YELLOW
GRAY RED
RED
BLUE
RED
ORANGE
ORG/WHT
ORG/WHT
RED
GREEN
RED
ORANGE
RED
ORG/WHT
BLUE
GREEN
ORANGE
Optex OS-12C
Controller
20VAC 50/60Hz
Microprocessor Controller
248901-
GYRO TECH
HOLD OPEN
NIGHT
ONE WAY
TWO WAY
MODE
M1
M0
Open
Gnd
Open
Open
Open
GndG nd
Gnd
Mode SW Usage
Adjustments to the door can only be made
with the NABCO Handy Terminal.
CAUTION
To maintain warranty,repairs must be
made by authorized NABCO facilities.
Do not disassemble the control box.
There are no user serviceable parts
inside.
POWER･2P INDICATORS
61
6B
H
62
BA
POWER
ERROR
MOTOR･12P
No.
WARNING
Toprotect against risk of fire
or electric shock,use only the
certified NABCO power supply.
RELATED DEVICES･16P
HANDY TERMINAL･6P
Mode Switch (see Mode SW Usage shown left)
61
7
9DC12V
6B
12VDC+
12VDC-(Common)
Interior Activation
Holding Beam
M0
H
M1
SLS
62
BA
Exterior Activation
Sidelite Presence Sensor
Breakout Detector
1
2
3
4
5
6
7
8
9
10
11
Reduced Opening Switch
No.
SYMBOL
FUNCTION [SLIDING DOOR]
7
12VDC-(Common)
OUT.C OUT.B
OUT.A
N/O
N/C
Common
Contact Output (Class2 Load only)
30V(42.4Vpeak)max.
5Amax.(0-20V), 3.2Amax.(20-30V)
OUT
Auxiliary Output (Open-Collector)
SQ
Sequential Activation
16 15 14
13 12
!
!
!
! !
NABCO
1
2
3
4
5
6
7
8 9
10 11 12
13
14 15
16
POWER SUPPLY
P/N 14-11741
AC115V ± 10%
50 / 60 Hz
Auxiliary 120 VAC Power Wires (These wires are
ON/OFF
Power Switch
BLUE
MAGNETIC POWER
DOWN SWITCH
P/N 22-9222
BLUE
BLACK
WHITE
GREEN
RED
BROWNWHITE
INTERIOR IXIO
PN 14-14264
U30 TERMINALU30 MICROPROCESSOR CONTROL LABEL
U30 TERMINAL P/N 14-11873
BLACK
BLUE
GREEN
RED
BROWN
White and Green wires from Sensor provide output for
On Remote Control Set: “F1” to “1”
If programming without the Remote: Parameter “13” to “1”
WHITE
TERM #5
RED
TERM #4
WHITE
WHITE
EXTERIOR IXIO
PN 14-14264