Napoleon PTHC38PK User manual

Manual,Instructions & Parts List
SRPH01 PROPANE PATIO HEATER
(FOR OUTDOOR USE ONLY)
-PTHC38PK-

2
TOOLS AND PARTS NEEDED FOR ASSEMBLYTOOLS AND PARTS NEEDED FOR ASSEMBLY
TOOLS NEEDED:
7/16 Wrench
3/8 Open End Wrench
Adjustable Opening Wrench, 8 Long
Philips Head Screwdriver
Leak Detection Solution ( Instructions how to make solution are included in page 9 )
＂
＂＂
WARNING
Note: 20 Pound, 5 Gallon LPG Tank is not
supplied
Note: 20 Pound, 5 Gallon LPG Tank is not
supplied
For outdoor use only.
Cylinders to be used must be constructed
and marked in accordance with US DOT
specifications.
The unit should be secured or moved indoors
if winds exceed 35 km/h.
Storage indoors is permissible only if the
cylinder is removed.
WARNING: Improper installation,
adjustment, alteration, services or
maintenance can cause injury, death or
property damage.
Read the installation, operating and
maintenance instructions thoroughly
before installing or servicing
this equipment.
DANGER
CARBON MONOXIDE HAZARD
This appliance can produce carbon monoxide
which has no odor.
Using it in an enclosed space can kill you.
Never use this appliance in an enclosed space such
as a camper, tent, car or home.

3
PARTSPARTS
4 Reflector Cap
5
6
1
2
3
4
5
4
12
1 Centre Reflector Cap
1 Head Assembly
3 M6 X 70mm Double Pointed Bolts
18 M6 Washers
12 M6 X10 Screws
13
11
6
7
8
11
12
9
10
13
1 Gas Hose
1 Post
1 Gas Cylinder Housing
4 M8 X 35mm Bolts
4 M8 Lock Washers
15 M6 Nuts
4 M8 Nuts
14
15
1 Regulator
1 Cylinder (Not Supplied)
8
11
12
10
13
14
7
9
7
1
2
3
9

4
PRECAUTIONSPRECAUTIONS
Do not use the heater in an explosive atmosphere.
Keep the heater away from areas where gasoline or other
flammable liquids or vapors are stored.
Prior to use, check for damaged parts such as hoses,
regulators, pilot or burner.
Always assure there is ample fresh air ventilation.
For outdoor use ONLY.
Never replace or substitute the regulator with any regulator
other than the factory suggested replacement.
Do not clean the heater with cleaners that are combustible
or corrosive.
Do not paint radiant screen, control panel or top canopy
reflector.
All leak tests should be done with a soapy solution. NEVER
USE AN OPEN FLAME TO CHECK FOR LEAKS.
The LP gas cylinder should be turned off when the
heater is not in use.
At least once a year, the unit should be inspected for the
presence of spiders, spider webs or other insects. Check the
heater immediately if any of the following exist:
1. The smell of gas in conjunction with extreme yellow
colored tips of the burner flames.
2. The heater does not reach temperature.
3. The burner makes popping noise during use (a slight
popping noise is normal when the burner is extinguished
after using).
The propane hose with regulator assembly shall be located
out of pathways where people may trip over it or in areas
where the hose will not be subject to accidental damage.
Children and adults should be aware of the hazards of high
surface temperature and shall stay away to avoid clothing
burn or ignition.
Young children should be carefully supervised when they
are in the area of the heater.
Clothing or other flammable material should not be hung
from the heater, or placed on or near the heater.
Installation and repair should be done by a qualified
service person. The heater should be inspected before
use and cleaning may be required at least once a year, or as
necessary. It is imperative that control compartment, burner
and circulating air passageways of the heater be kept
clean.
Keep the appliance area clear of combustible materials
such as gasoline and other flammable vapors and liquids.
Do not obstruct the flow of combustion and ventilation air.
Keep the ventilation opening of the cylinder enclosure free
and clear of debris.
NOTE: PLEASE READ THE FOLLOWING SAFETY RULES
The appliance shall not be used in basements or below
ground level.
It must always be placed on a solid and level surface.
Read the instructions before use.
This appliance must be installed in
accordance with such regulations as
are in force.
This appliance must only be used outdoors.
Using this product in an enclosed area may cause
injury, death or property damage.
WARNING
Disconnect LPG bottle before moving the heater.
Any guard or other protective device removed for
servicing the heater must be replaced prior to
operating the heater.
Do not attempt to alter unit in any manner.
EXAMPLE: using the heater without the top canopy
reflector or radiant screen.
Do not shorten the burner post assembly.

ASSEMBLY FOR LIGHT SYSTEMASSEMBLY FOR LIGHT SYSTEM
WARNING:
TO BE INSTALLED ONLY BY AN
AUTHORISED PERSON
Instruction For Battery Installing
Upon first time use of the product,please remove the
ignition button and install an AAA battery as indicated.
Ignition button
Replace Battery
Control knob
Ignition button
AAA battery
5

6
ASSEMBLYASSEMBLY
NOTE: Assembly of this heater requires
basic mechanical skills. Proper assembly
is the responsibility of the installer.
Place the post on the top of the gas cylinder
housing. Fasten the post to the gas cylinder
housing using the four (4 pcs)
Step 1
M8 35mm Bolts ,
8mm Lock Washer ,
Nuts for M8 35mm Bolts .
5
12
10
X
X
6
Slide the gas hose with the attached
Head assembly through the top of the post and
down through the hole in the top of the gas
cylinder housing. Screw the combustion assembly on
to the post, and tighten securely.
3
4
5
Step 2
8
Step 1 ----Attach Post to Gas Cylinder Housing
Step 2 ----Attach Head Assembly to Post

7
ASSEMBLYASSEMBLY
NOTE: Assembly of this heater requires
basic mechanical skills. Proper assembly
is the responsibility of the installer.
Step 4 ---- Attach Center Reflector to Reflector
Attach center reflector to the top of reflector (4 pcs)
by M6 X 10 mm screws (12 pcs) ,
Step 4
2
1
11
6mm washers (12 pcs) and nuts (12 pcs).
7
9
Step 3 ----Attach Double Pointed Bolt to
Attach double pointed bolts (3 pcs) and
6mm washers (3 pcs) to the top of head assembly
and tighten the bolts securely.
Head Assembly
Step 3
9
13
3

8
ASSEMBLYASSEMBLY
Step 5
3
Step 5 ----
Attach Center Reflector and Reflector
Load center reflector and reflector to the top
of head assembly by
double pointed bolts (3 pcs)
to the top of Head Assembly
6mm washers (3 pcs) and nuts (3 pcs)
7
9
13
NOTE: Assembly of this heater requires
basic mechanical skills. Proper assembly
is the responsibility of the installer.
Step 6
Step 6 ---- Connect Gas Line to Cylinder
Attach Gas hose to regulator hose with
3/8 Inch Open End Wrench and
Adjustable Wrench.
Attach regulator to cylinder. Tighten securely.
Move cylinder to the plate of base assembly.
4
14
15

9
SAFETY CHECKSSAFETY CHECKS
NOTE: Always check the following
connections.
Check all connections on the hose regulator
assembly.
Check the regulator to the LP gas cylinder
connection. Note that the regulator adapter is
a reverse thread.
Check the hose to the intake pipe to make
certain that it is not kinked or in a position that
could cause it to kink. Hand tighten and then
take a 1/2 turn with an adjustable wrench.
The remaining connections are to be tested after
this heater has been lit. (SEE LIGHTING
INSTRUCTIONS PAGE10)
Check for leak
Your Patio Heater has been checked at all
factory connections for leaks,To check at the
Connection at the gas hose/regulator/cylinder.
1) Make leak solution by mixing 1part liquid
dishsoap and 3 parts water.
2) Spoon several drops (or use squit bottle)
of the solution onto the gas hose/regulator
and regulator/cylinder connection.
3) Inspect the connections and look for bubbles.
4) If no bubbles appear, the connection is safe.
5) If bubble appear, there is leak,loose and
re-tighten this connection.

10
OPERATIONOPERATION
FOR YOUR SAFETY:
If at any time you are unable to light burner
and smell gas,wait 5 minutes to allow gas
to dissipate before attempting to light heater.
If,after 1 minute, you are unable to light
burner, wait 5 minutes and allow flammable
vapors to dissipate before attempting to
light heater
WARNING
FOR YOUR SAFETY:
Do NOT touch or move heater for at least 45
minutes after use.
Allow emitter and dome to cool before
touching.
WARNING
WARNING:
Do NOT attempt to operate heater until you have
read and understand all precaution .
Failure to do so can result in serious personal injury, death,
or property damage.
Before Turning Gas Supply ON
Your heater was designed and approved for OUTDOOR USE ONLY. Do NOT
use it inside a building ,or any other enclosed area.
Make sure surrounding areas are free of combustible materials, gasoline,
and other flammable vapors or liquids.
Ensure that there is no obstruction to air ventilation.
Be sure all gas connections are tight and there are no leaks.
Be sure the access panel is clear of debris.
Be sure any component removed during assembly or servicing is replaced
and fastened prior to starting.
Before Lighting
Heater should be thoroughly inspected before each use, and by a qualified
service person at least annually.
If relighting a hot heater, always wait at least 5 minutes.
Our heater is manufactured under good quality.
There should be at least eight effective times within ten times of ignition.
If you experience any ignition problem, turn off the heater and gas
supply, and consult "Troubleshooting" on page 14. Ignition Hole
Emitter Screen
LIGHTING INSTRUCTIONS
1)Turn the control knob to "OFF" position.
2)Fully open gas valve
3) Push in control knob and turn counter clockwise to "PILOT"
position, push in the ignition button and keep the button depressing untill
light the pilot.
4) Once the pilot is lit, continue to keep the control knob depressed for at least
30 seconds, After 30 seconds release control knob.
5) If pilot does not stay lit, repeat steps 3 and 4.
6) If pilot still does not stay lit, then:
a) Push in gas control knob and turn counter clockwise to "PILOT"
b) keep depressing the control knob, put long stem lighter into the
Ignition Hole on the emitter screen to light the pilot.
c) repeat step 4.
7) Push in and turn control knob counter clockwise to "HIGH" position,
If you want a lower temperature, push in the control knob and turn
clockwise to the "LOW" position.
P
u
s
h
t
o
t
u
r
n
O
F
F
H
G
I
H
L
O
W
T
O
L
I
P
P
u
s
h
t
o
t
u
r
n
O
F
F
H
G
I
H
L
O
W
T
O
L
I
P
Eletronic ignition

OPERATIONOPERATION
""OW
""OW
CAUTION :
NOTE:
When heater is ON:
Avoid inhaling fumes emitted from the heater's
First use.Smoke and odor from the burning of oils used in
manufacturing will appear.Both smoke and odor will
dissipate after approximately 30 minutes. The heater
should NOT produce thick black smoke.
The burner may be noisy when initially turned on. To eliminate excessive
noise from the burner,turn the Control Knob to the LOW position. Then,
turn the knob to the level of heater desired.
Emitter screen will become bright red due to intense heat. The color is more
visible at night.Burner will display tongues of blue flame.These flames
should not be yellow or produce thick black smoke,indicating an obstruction
of airflow through the burners.
RELIGHT
1)Turn the control knob to OFF position.
2)Wait five (5) minutes before attempting to relight pilot.
3) Repeat steps beginning with step 2 of the Lighting Instruction above.
SHUT DOWN INSTRUCTIONS
1) Push in and turn control knob clockwise to "OFF" position.
2) Turn L.P. tank gas valve clockwise to "OFF" position when
heater is not in use
Note: After use, some discoloration of the emitter screen is normal.
WARNING :Heater will be hot after use.
Handle with extreme care.
2＂
1＂
0＂
11
OPERATIONOPERATION
P
u
s
h
t
o
t
u
r
n
O
F
F
H
G
I
H
L
O
W
T
O
L
I
P
P
u
s
h
t
o
t
u
r
n
O
F
F
H
G
I
H
L
O
W
T
O
L
I
P

12
LOCATING HEADER FOR USELOCATING HEADER FOR USE
BE CAREFUL: WHEN CERTAIN
MATERIALS OR ITEMS ARE LEFT
UNDER THIS SPACE HEATER WHILE
IN USE, THEY WILL BE SUBJECT TO
RADIANT HEAT AND COULD BE
SERIOUSLY DAMAGED.
This heater is primarily used for the
heating of outdoor patios, decks, spas, pool
and working areas.
Always make sure that adequate fresh air
ventilation is provided. Follow the spacing
tolerances shown in Figure 1.
This heater clearances, shown in Figure 1,
must be maintained at all times.
The installation must conform to local codes,
or in the absence of local codes, with the
standard for the storage and handling of
liquid petroleum gases, ANSI/NFPA 58-1986,
or most recent addition. For Canada, with the
current CAN1-B149.
This heater must be placed on level, firm
ground.
Never operate in an explosive atmosphere.
Keep away from areas where gasoline or
other flammable liquids or vapors are stored
or used.
Figure 1
24" 24"
36"

13
""OW
WARNING
DO NOT touch or move heater for at least 45
minutes after use.
Allow all burner elements to cool before
touching.
FOR YOUR SAFETY :
NOTE
In a salt-air environment (such as near an
ocean). corrosion occurs more quickly than
normal. Frequently check for corroded areas
and repair them promptly.
STORAGE :
Between uses:
Turn LP cylinder to OFF position.
If desired, cover heater to protect ecterior surfaces and to help prevent
build up in air passages.
Store heater upright in an area sheltered from direct contact with
inclement weather (such as rain, sleet, hail, snow, dust and debris).
During periods of extended inactivity or when transporting;
NOTE
Wait until heater is cool before covering.
""OW
Turn the control knob to OFF position.
STORAGE/CLEANINGSTORAGE/CLEANING
Turn the control knob to "OFF" position.
Disconnect LP Cylinder and move to a secure, well-ventilated area
out of the reach of children and stored outdoors.
Do NOT store in a location that will exceed 125 degrees F.
Store heater upright in an area sheltered from direct contact with
inclement weather (such as rain, sleet, hail, snow, dust and debris).
If desired, cover heater to protect ecterior surfaces and to help prevent
build up in air passages.
CLEANING :
1
2
3
Emitter
Screen
Lower
Cone
Cylinder
1.Remove the reflector and emitter by removing the 4 pcs screws ( )
that fasten the emitter to the lower screen cone .
Any debris in the burner port should be cleared. Any rust can be
removed carefully with a wire brush. Never use a piece of wood,
or other materials that might break off and block the ports.
2.Remove lower cone cylinder by removing the 4 pcs screws ( )
which attach the lower cone cylinder to the control cylinder.
Clear debris on the surface of thermocouple.
3.Remove the 4 pcs screws ( ) at the bottom of control cylinder.
Clear the debris of the surface and the inside of the injection nozzle.
1
Control
Cylinder
2
3
It is recommended that this heater painted body components from the
emitter down are periodically protected with a coat of automobile wax.
If repainting is necessary, paint only the post and gas cylinder housing.
Never paint the reflector, combustion assembly, or instruction plate on post.
NOTE :
Keep exterior surfaces clean:
Use warm soapy water for cleaning. Never use flammable of
corrosive cleaning agents.
While washing your unit, be sure to keep the area around the combustion
assembly dry at all times. If the gas control is exposed to water in any way,
do NOT try to use it. It must be replaced.

14
TROUBLESHOOTINGTROUBLESHOOTING
PROBLEM PROBABLE CAUSE SOLUTION
Pilot will not light Gas valve may be OFF Turn the gas valve ON
Orifice blocked Clean or replace Orifice
Air in supply system Purge air from lines
Pilot will not stay on Debris around pilot Clean dirty area
Loose connection Tighten connection
Thermocouple bad Replace Thermocouple
Gas leak in line Check connections
Burner will not light Pressure is low Fuel tank is near empty
Orifice blocked Remove, clean and replace
Control Valve not ON Turn valve to ON
Thermocouple bad Replace Thermocouple
Pilot light assembly bent Place pilot in proper
or not in correct location position and retry
Fuel Tank empty Refill LP gas tank
Lack of fuel pressure Fuel tank is near empty
No Battery Replace Battery