Nauticam NA-Ultra5 Housing User manual

NA - Ultra5 Housing
For SmallHD Ultra5 Camera Monitor
PN 17926
Introduction 2
2
3
4
7
8
Package Contents
Important Instructions
Part Names and Functions
Opening the Housing
Closing the Housing
9
16
13
Setup Options
Preparation for Use
Cable Connection
19
20
21
Care/Storage
Warranty
Specications
User Manual
Housing
Monitor
July, 2023

2
INTRODUCTION
PACKAGE CONTENTS
Thank you for purchasing this Nauticam product.
Before using the product, please read this manual thoroughly to familiarize yourself with full scope of functions on the
product as well as ensuring that you will use the product correctly.
Make sure that you have all the included items listed below before using this product.
If some items are missing or damaged, contact your local Nauticam dealer.
Pre-installed items :
# 25625 M16 Vacuum Valve II
# 25089 M28 HDMI 2.0 Adapter
# 17958 Mounting Ball
Monitor Hood
Manual Instruction Card Padded Travel Case
Hand Pump
After purchase, we suggest that you reuse all packaging materials for future travelling.
Panasonic CR2032 Battery
(pre-installed for Moisture Alarm)
Spare Main O-ring
# 90254
O-ring Remover
Lubricant

3
IMPORTANT INSTRUCTIONS
Water-tight test of the housing (without
monitor inside) before usage is recom-
mended as well as any O-ring renewal
and port change.
Use only Nauticam lubricant on silicone
rubber O-ring.
Discontinue use immediately when there is
a sign of leakage.
Do not expose the housing in direct
sunlight for a prolonged period.
Prevent any sand or dust or water pen-
etration inside the housing. Be extra
careful when inserting or removing the
monitor.
This product is not intended for use by
children, or persons with reduced physical,
sensory or mental capabilities, or lack of
experience and knowledge, unless they
are supervised and/or given instruction by
a responsible person concerning use of
the product to ensure that they can use it
safely.
Do not seal the housing when travelling by
air as this may lead to a pressure difference
between the atmosphere and inside the
housing.
Only the accesories specied by
Nauticam must be used. Third-party
accessories may result in malfunctions
or damage to the product.
Do not stretch any O-rings excessively.
Only remove it using Nauticam O-ring
remover.
Do not open the housing in wet or sandy
environment. Protect the housing from
moisture and debris in order to prevent
malfunction or leakage.
1
3
5
7
9
11 12
4
6
8
10
2
Do not attempt to remove parts of the
housing yourself. Repairs must be done
at authorized service centers only.
The housing should be positioned on the a
stable and safe surface on land.

4
PART NAMES AND FUNCTIONS
Joystick - Right button Joystick - Up button
Joystick - Left button Joystick - Down button
Back button Custom - F1 button
Custom - F3 buttonCustom - F2 button
1 2
3 4
5
7
6
8
Rear View
2
4
5
8
6
7
3
1
A
Joystick - CenterA

5
PART NAMES AND FUNCTIONS
M28 Accessory port Mounting ball
Sacricial zinc anodes
1 2
3
Front + Bottom Views
3
2
1

6
PART NAMES AND FUNCTIONS
Top + Side Views
Pre-installed M16 Vacuum valve II
ON/OFF button Housing unlock button
Moisture alarm window M28 Accessory port
Pre-installed M28 HDMI 2.0 Adaptor
3
5 6
1 2
4
3
4
1
6
5
2

7
OPENING THE HOUSING
1
2
3
depress housing unlock button
turn housing lock latch
anti-clockwise to open the
housing
ip open the back housing
when lock latch is aligned to
‘open’ position
* drawings as illustrations only

8
CLOSING THE HOUSING
1
2
3
before closing the housing, clean
and lubricate the main O-ring
make sure nothing is caught
between front and back housing
and that they are fully aligned
before locking
main O-ring
insert the housing shaft into the
shaft hole and then rotate the lock
latch clockwise until you hear and
feel it click into place
housing locked in place securely
* drawings as illustrations only

9
SETUP OPTIONS - HDMI 1.4
HDMI IN
HDMI IN + SDI OUT
Internal HDMI Cable
Internal HDMI Cable
25089
25089
25082
25082
25060
25064 or 25065
25080 + 25058
25033 + 25081 or 25080
25033 + 25081 or 25080
or
or
or
M28 HDMI 2.0 Adapter
(pre-installed)
M28 HDMI 2.0 Adapter
(pre-installed)
HDMI 1.4 Cable
HDMI 1.4 Cable
SDI Cable in 0.4m length
SDI Surface monitor cable
15m or 45m
M28 to M16 Adaptor +
M16 SDI Bulkhead
M16 HDMI Bulkhead +
M24 to M16 Adaptor or
M28 to M16 Adaptor
(depending on camera housing)
M16 HDMI Bulkhead +
M24 to M16 Adaptor or
M28 to M16 Adaptor
(depending on camera housing)
* drawings as illustrations only
Connect to surface
Connect to housing
Connection with Camera Housing
1
1
1
1
1
3
3
3
3
2
22

10
SETUP OPTIONS - HDMI 2.0
HDMI IN
* drawings as illustrations only
HDMI IN + SDI OUT
Connection with Camera Housing
1
1
3
3
2
2
25089 + 25086
25089 + 25086
M28 HDMI 2.0 Adaptor or
M24 HDMI 2.0 Adaptor
(depending on camera housing)
M28 HDMI 2.0 Adaptor or
M24 HDMI 2.0 Adaptor
(depending on camera housing)
Connect to surface
Connect to housing
HDMI 2.0 Cable
HDMI 2.0 Cable
25089
25089
or or
or
M28 HDMI 2.0 Adapter
(pre-installed)
M28 HDMI 2.0 Adapter
(pre-installed)
1
1
3
3
25060
25064 or 25065
25080 + 25058 or
SDI Cable in 0.4m length
SDI Surface monitor cable
15m or 45m
M28 to M16 Adaptor +
M16 SDI Bulkhead
1 2
2