NEC SL1100 User manual

Multi-Line Terminal
User Guide
Smart Communication Server
Please read this manual carefully before operating
this product and save this manual for future use.

1
Before using Your Terminal…
Thank you for purchasing NEC SL1100 system.
Due to the flexibility built into the system, your Dialing Codes and Feature Capacities may differ
from those in this guide. Check with your NEC Authorized Supplier / System Administrator and
make a note of any differences.
Installing the Handset and Line Cord
When installing the handset :
1. Make sure the handset cord is plugged into
the handset jack on the telephone base.
2. The line cord routes through the channel on
the telephone base.
3. Alternatively the line cord can route through
the channel on the telephone legs.
Handset Cord
Cord can be installed
either way
Adjust the two-position Viewing Angle
To set the low viewing angle position:
1. Fold the legs all the way back.
To set the high viewing angle position:
1. Flip up the two leg supports.
2. Fold the legs back until the supports contact the base.
NEC Corporation reserves the right to change the specifications, functions, or features at any time without notice.
NEC Corporation has prepared this document for use by its employees and customers. The information contained
herein is the property of NEC Corporation and shall not be reproduced without prior written approval of NEC
Corporation.
Copyright 2011- 2012, NEC Corporation
Printed in Japan

2
Using Your Terminal
Handsfree Options
-Handsfree lets you place and answer calls by pressing “Speaker” instead of using the handset.
-With Automatic Handsfree, you can press a Speaker Key without lifting the handset. Normally, you have
Automatic Handsfree.
-Use HandsfreeAnswerback to answer a voice-announced Intercom call by speaking toward your phone without
lifting the handset.
Exit Key
Exit any screen and return
the display to “Time & Date”.
Dial Keys HOLD Key
Press this key to place
an internal or external
call on hold.
Speaker Key
Controls the built-in speaker, which
can be used for Handsfree dialing/
monitoring. LED on key lights when
key is active. Enter
Key
Redial
Key
Volume (UP) Key
Incoming Call
History Key
* 12 Programmable Function Keys are available for IP4WW-12TXH-B TEL.
24 Programmable Function Keys are available for IP4WW-24TXH-B TEL.
** The illustration shows IP4WW-24TXH-B TEL.
Directory Functions
or
Volume (DOWN) Key
Handset
Speaker
IP4WW-( )*TXH-B TEL Call Indicator Lamp
This lamp flashes fast when a call is ringing and
flashes slower when a message has been left.
Alphanumeric Display
The LCD has 3 lines, 24 characters with
backlight.
Soft Keys
The Soft Keys show the available features for
your current activity. Any feature shown at the
bottom of the LCD is available.
Help Key
The user can press this key followed by a
programmable key to check what Line or
Programmable Feature is assigned on the key.
Programmable Function Keys
Flexible Line keys or Feature Keys assigned by
the System Administrator.
Flash Key
Press key to finish an outside call and hear the
dial tone.
Transfer Key
Allows the extension user to transfer established
calls to another extension.
DND Key (Do Not Disturb)
Setup a Do Not Disturb if pressed during a call.
Mute (Microphone) Key
Mute handset or Handsfree Microphone. LED
lights when microphone is muted.
Clear/Back Key
Press this key to cancel the current action or
delete a character.
Cursor Key
Access various features with simple operation.

3
For Your Convenience
Programmable Function Keys
Programmable Function Keys can be assigned as “Trunk” Key and/or other Function Keys. You can just
press the function key to activate the assigned function without dialing the Service Code.
Function Code &Add Data
Function Key
7 ???
Speaker
5 1
7 5 2
Speaker
There are 2 levels of Function Keys. (General Keys : assigned by 751, Appearance Keys : assigned by
752)
Appearance Keys have priority. You can overwrite the Appearance Key at the General Key.
If you want to overwrite the General Key at the Appearance Key, you have to erase the Appearance Key by
dialing “752 + 000” before General Key assignment.
In the default setting, Programmable Function Key No. 1 to 12 is assigned as “Trunk” Key. If you want to
assign Function Keys (General) at the unused Trunk Keys, these unused keys should be erased by dialing
“752 + 000”.
Programmable Function Keys can be erased by dialing “752 + 000” or “751 + 00”.
Programmable Function Keys can be assigned by Soft Key operation as well.
DSS / One-Touch Keys
Programmable Function Keys can be assigned as DSS (Direct Station Selection) or One-Touch Keys. You
can place an Outside / Intercom Call by just pressing this key without dialing the number.
Function Key
7 0 1
Speaker
5 1
Speaker
Telephone NumberTrunk Access Code
9 ? ? ?
Extension Number
???
Hold
To change the Trunk Access Code, ask your NEC Authorized Supplier for the details.
In the default setting, Programmable Function Key No. 1 to 12 is assigned as “Trunk” Key. If you want to
assign DSS Keys to the unused Trunk Keys, these unused keys should be erased by dialing “752 + 000”
before performing the above operation.
For the DSS Key, the extension status can be indicated on the BLF. (idle : extinguished, Busy : lit)
When you register a telephone number, the Trunk Access Code should be added in front of the number.
Up to 36 dialing digits can be registered, but the name can not be registered.
If you want to continue the operation, press Programmable Function Key instead of Speaker Key to finish.
One-Touch Keys can be assigned using Soft Key operation.

4
For Your Convenience
Abbreviated Dial (Speed Dial) Registration
7
Speaker
5 3
Speaker
Telephone Number
???
Hold
Common ABB
7 5 4
Group ABB
ABB Bin Number
? ? ?
Name
???
Hold
The number of digits dialed for Bin No. depends on the system setting (0-9<Only Group ABB> / 00-99 /
000-999).
System setting is necessary for GroupABB function. Ask your NEC Authorized Supplier for the details.
Name can be entered by Dial Pad Keys. (See below)
Up to 36 dialing digits can be registered, and up to 12 characters can be registered as name.
If you want to continue the operation, dial Bin No. instead of Speaker Key to finish.
You can skip to enter the name. (No enter any character, then press “Hold” Key).
You can erase the registered number & name by pressing “Exit” Key after dialing Bin No..
Common Abbreviated Dial can be registered using Soft Key / Cursor Key operations.
0 ! “ # $ % & ‘ ( ) Ô Õ ú å ä æ ö ü α
εθβ
0
1 @ [ ] ^ _ ‘ {¥ }| ÁÀÂÃÅÆ
É ÇÊÌÓφ
A B C a b c 2
D E F d e f 3
G H I g h i 4
J K L j k l 5
M N O m n o 6
P Q R S p q r s 7
T U V t u v 8
W X Y Z w x y z 9
2
3
4
5
6
7
8
9
1
+ , - . / : ; < = > ?π Σ σ Ω ∞ ¢ £
When you enter a name, use Dial Pad Keys to enter letters as below. For example, press “2” key once for “A”,
twice for “B”, etc.
#
A
ccepts a character and moves
the cursor one place to the right.
Press twice to insert a “space”.
Clears the character entry to the
left, one character at a time.
(Backspace)
Clear/Back
Entering Alphanumeric Characters

5
Placing Calls
Place an Outside Call <Quick Access>
Telephone Number
????
Place an Intercom Call <Dial Access>
Extension Number
? ? ?
Trunk Key
Listen to the Dial Tone before dialing a Telephone Number.
You can have function keys for Trunks or Trunk Groups. Ask your NEC Authorized Supplier for the details.
Place an Outside Call <Access by Code>
7
Speaker
0 4
Telephone NumberTrunk Access Code
? ? ?
(e.g. : 005 = Trunk No.5)
?
??9# ?
Trunk Group No.
Trunk No.
To change the Trunk Access Code, ask your NEC Authorized Supplier for the details.
Listen to the Dial Tone before dialing a Telephone Number.
If the Trunk Group number is greater than 10, you should enter 2 digits (e.g. 11 : Group 11) after dialing
“704”. Ask your NEC Authorized Supplier for the details.
Ask your NEC Authorized Supplier for the Trunk Number dialing digits.
Speaker
Your call will ring or voice-announce. If you hear ringing, wait for an answer. If you hear a beep, begin
speaking. Dialing “1” changes voice/ring mode (if the destination is Multi-line Terminal).
9

6
Placing Calls Quickly
# 5
Directory Dialing
On-Hook
Condition
Press several times to search
Last Number Dialing
On-Hook
Condition
Press several times to search
Redial List
Quick Redial Speaker
Callback by Received Number
The system retains the last 10 numbers dialed, which can be reviewed and redialed.
To cancel the Redial List operation, press “Clear/Back” Key.
Caller-ID function is required to use this operation for outside calls. Ask your NEC Authorized Supplier for
more details.
To cancel the Callback operation, press “Clear/Back” Key.
Search 1/90
_
ABC Ltd
S
earch 6/24
N
NEC CORP
Dialed Number 01/10
2142622000
DEC TUE 22 03:29PM
D
ialed Number 03/10
9725551399
DEC TUE 22 01:12PM
Received Call 01/10
8175556000
DEC TUE 22 04:31PM
R
eceived C
a
ll 03/10
4695551012
DEC TUE 22 11:38AM
On-Hook
Condition
Press several times to search
After searching the desired destination, press “Enter” Key to confirm the telephone number before lifting the
handset, if necessary.
You can enter more characters (up to 12) to make desired destination’s search even more specific.
You can also search the desired destination without entering the characters (press Cursor Keys only).
To cancel the Directory Dialing operation, press “Clear/Back” Key.
Directory Dialing can be activated using Soft Key operation.
?
1st Character
you want to search
L
INE 03
Lnd Save Rls
Trunk Key

7
Abbreviated (Speed) Dialing <for Outside>
Common
ABB
Group
ABB
Common ABB Bin Number
? ? ?# 2
Group ABB Bin Number
? ? ?# 4
Speaker
Speaker
Common ABB Key
(SC751+27)
Group ABB Key
(SC751+28)
The digit of Bin No. depends on the system setting (0-9 <Only Group ABB> / 00-99 / 000-999).
Telephone Numbers are pre-registered to the system.
System setting is necessary for GroupABB function. Ask your NEC Authorized Supplier for the details.
When you assign the Common ABB Key on the Programmable Function Key, “Press HOLD” is required
after dialing the Function Code 27.
Placing Calls Quickly
One-Touch / DSS Call
One-Touch / DSS Key
(SC751+01)
Telephone / Extension number should be pre-registered to a One-Touch / DSS Key.
Trunk Access Code should be added in front of the Telephone Number.
On-Hook
Condition

8
L
INE 03
Conf Save Time More
Set Camp On / Callback
Camp On
750
Hear Busy Tone
or No Answer Callback
Wait without
hanging up
Wait for the
System to call
you back
Camp On Intercom Call - When you hear ringing, wait for the called party to answer.
Outside Call - When you hear Dial Tone, begin telephone number dialing.
Callback Intercom Call - When your terminal starts the ringing, lift handset and wait for the called party
to answer.
Outside Call - When your terminal starts the ringing, lift handset, hear Dial Tone, and begin
telephone number dialing.
This function is applicable in case all trunks are busy condition (not applicable for dialed outside party
busy).
Cancel Camp On / Callback
(Camp On)
77 0
If your call doesn’t go through…
Camp On Key
(SC751+35)
Repeat Dialing <Outside Call Only>
Hear Busy Tone
or No Answer
Repeat Dial Key
(SC751+29)
When the Repeat Dialing is set, Repeat Dial Key flashes and the system automatically and periodically
redials a call. Repeat duration is programmable. Ask your NEC Authorized Supplier for the details.
You should lift the handset when the called party answers.
Press flashing Repeat Dial Key to cancel.
LINE 03
Park Trf More
L
INE 03
Rpt More
2
-
8
TUE 3:03PM
Busy 216
MW Camp Barg
During calling (NoAnswer) : Press “More” to find “Camp”

9
Set a Message Waiting
0
Hear Busy Tone
or No Answer
0
Cancel Message Waiting
Extension Number
? ? ?7 7 1
7 7 3
Individual
Cancel
(originated extension)
All Cancel
(at any extension)
MW Key
(SC751+38)
MW Key
(SC751+38)
On-Hook
Condition 0
Help
When you set a MW, the called party’s Indicator starts to flash, and your Indicator is lit Red.
Answer a Message Waiting (Your terminal’s Indicator is flashing Red)
Check & Answer
Quick Answer
If your call doesn’t go through…
When you answer a MW, the Indicator automatically goes off when the called party answers.
If multiple message are in queue, you can select the desired party by pressing Up key after dialing ” , 0”.
2
-
8
TUE 3:03PM
MW

10
Answering Calls
Answering an Outside Call
#
7 6
Ringing
Picking up a Call for other Extensions
In same
Group
In other
Group
Specified
Extension
9
Extension Number
? ? ?
System setting is necessary to create a Call Pickup Group. Ask your NEC Authorized Supplier for the
details.
Call Pickup operations are available using Soft Key operation.
Speaker
Ringing
Extension
Non-Ringing
Extension
Trunk Key
(Flashing)
Confirm the status of Mute Key if you want to answer by Handsfree (Mute On : LED On, Mute Off : LED
Off).
Answering an Intercom Call
Ringing
Speaker
Signal Mode
Extension
Voice Mode
Extension
Intercom Call Mode (Signal or Voice) can be set at your terminal by :
“Signal” : Speaker -> 723 “Voice” : Speaker -> 721
Confirm the status of Mute Key if you want to answer by Handsfree. (Mute On : LED On, Mute Off : LED
Off)
Voice
Speak toward
your terminal
Speaker
Call Pickup Key
(SC751+24)
Speaker
Call Pickup for other
Group Key
(SC751+25)
Speaker

11
Hold / Transferring Calls
Holding a Call / Retrieving a Held Call
Talking
Hold Retrieve
When on an Intercom, the call is held as “Exclusive Hold” on your terminal.
This operation puts your outside call on System Hold. Other extension users can take the call off Hold.
Retrieve a Held Outside Call
Trunk Number you want to retrieve
?? ?6 7 2
Ask your NEC Authorized Supplier for the details about your Trunk Number dialing digits.
Transferring a Call to the other Extension
Talking
Extension Number
? ? ?
Announce
Hold
Trunk Key
(Flashing)
Hold
(Flashing)
Outside
Call
Intercom
Call
Holding a Call Exclusively
Talking
Hold Retrieve
This operation puts your outside call on Exclusive Hold. Other extension users can not take the call off Hold.
Trunk Key
(Flashing)
Hold
(Flashing)
Outside
Call
Intercom
Call
Exclusive Hold Key
(SC751+45)
Speaker
Hold
Transfer
If your terminal has DSS/One-Touch key, just press it instead of “HOLD” and “Extension Number” dialing.
2
-
8
TUE 3:03PM
Calling 300
Trf More

12
For more Convenient Use…
Do Not Disturb (DND)
1
2
3
4
DND : Trunk Incoming Call
DND : Intercom Incoming Call
DND : Trunk & Intercom Incoming Call
DND : Transferred (CFW) Call
When you set DND function, DND Key is lit and the Internal Dial Tone pattern changes.
Talking
You can repeat this operation to add more parties.
You may be able to have up to 16 parties (including your terminal). You may need to adjust the volume
level due to the environment where calls are placed. Ask your NEC Authorized Supplier for the details.
Repeat for
additional parties
Conference
Start
Conference
On-Hook
Condition DND
0DND : Cancel
Extension Number
? ? ?
Telephone Number
? ?
Trunk Key
2-8 TUE 3:03PM
Conf
2
-
8
TUE 3:03PM
Add Rls
CONF
Begin Dir
Talking

13
1
0
7 4 1
Extension Number
???
Set
Cancel
When you set Call Forward / Follow Me, the destination extension is displayed on the LCD and the Internal
Dial Tone pattern is changed. (Call Forward / Follow Me can be set using a Soft Key).
Call Forwarding / Follow Me
Call Forward Immediate
Speaker
Call Forward
Immediate Key
(SC751+10)
Speaker
On-Hook
Condition
1
0
Extension Number
???
Set
Cancel
Call Forward when Busy
Speaker
Call Forward
when Busy Key
(SC751+11)
Speaker
On-Hook
Condition
1
0
7 4 3
Extension Number
???
Set
Cancel
Call Forward when No Answer
Speaker
Call Forward when
No Answer Key
(SC751+12)
Speaker
On-Hook
Condition
1
0
7 4 4
Extension Number
???
Set
Cancel
Call Forward when Busy / No Answer
Speaker
Call Forward when
Busy / No Ans Key
(SC751+13)
Speaker
On-Hook
Condition
For more Convenient Use…
7 4 2

14
For more Convenient Use…
Call Forwarding / Follow Me (Cont’d)
1
0
7 4 5
Extension Number
???
Set
Cancel
Call Forward Both Ring
Speaker
Call Forward
Both Ring Key
(SC751+14)
Speaker
On-Hook
Condition
1
0
7 4 6
Extension Number
???
Set
Cancel
Call Forward Follow Me
Speaker
Call Forward
Follow Me Key
(SC751+15)
Speaker
On-Hook
Condition

15
Soft Keys Operation
2-8 TUE 3:03PM
200
Menu Dir VM:00 CL:00
“Menu” Soft Key
The following table shows the menu structure of “Menu” Soft Key. You can reach the desired feature using
the following operation.
Prev Next Select Back Prev Next Select Exit
It is possible to search the desired feature by pressing Cursor the Keys (Up / Down / Right / Left) several
times instead of “Prev” or “Next” Soft Keys, or it’s possible to access the desired feature directly by dialing
the 2 digit Menu Code after pressing the “Menu” Soft Key.
Item Menu Code Next Operation after pressing the “Select”
10 : Volume
Preference
11 : Ring
12 : Off-Hook Ring Press “Down” or “Up” to adjust the selected option.
20 : Display
Preference
21 : Contrast
22 : Min Brightness
23 : Max Brightness
Press “Down” or “Up” to adjust the selected option.
30 : Feature
Preference
31 : Voice Announce
32 : Handsfree Reply
33 : Auto Call Timer
34 : Preview Dial
35 : Illuminated Dialpad
36 : Auto Call Screening
37 : Incoming Page
38 : Ringing Line Preference
39 : Auto Backlit
For the selected option, press “On” (enable) or
“Off” (disable).
40 : Ring
Preference
41 : Intercom
42 : Line Keys
43 : Each Line Keys
Press “<<” or “>>” to select and save option.
50 : Key
Assignment
51 : Feature Keys
52 : Primeline Key Press “<<” or “>>” to select and save option.
60 : Call
Forwarding
61 : Immediate
62 : Ring No Ans
63 : Busy No Ans
64 : Call Forward AME
65 : Display Message
66 : Follow Me
67 : Both Ring
Press “Set” or “Cancel”, enter the destination and
select option to save.
70 : Speed Dial 71 : Personal Speed Dial
72 : Company Speed Dial Enter Bin number and Phone number, Name and
save.
80 : Name and
Language
81 : Extension Name
82 : Display Language For Name, enter the name using Alphanumeric Characters, For Language, press “<<” or “>>” to
select and save.
90 : Option
Preference
91 : Headset Mode
92 : Headset Voice Announce
93 : System Information
94 : VoIPDB Information
95 : Auto Backlit (Threshold)
96 : IP Address Information
97: IP Phone log off
98: Change login password
For Headset option, press “On” (enable) or “Off”
(disable).
For System / VoIPDB information (IP Address, MAC
Address), press “Select”. For Auto Backlit, select
threshold option to save.
00 : Admin 01 : Time
02 : Date
03 : Extension Name
04 : Clear All Call Fwd
05 : System Night Key Mode
For Time, Date and Extension Name, enter the
Time, Date and Extension Number and Name to
save. For Clear All Call Fwd, press “Yes”.

16
Soft Keys Operation
2-8 TUE 3:03PM
200
Menu Dir VM:00 CL:00
“Dir” Soft Key
You can activate the Directory Dialing feature by pressing the “Dir” Soft Key.
S
earch 1/90
_
ABC Ltd
2-8 TUE 3:03PM
200
Menu Dir VM:03 CL:00
“VM” Soft Key (Option)
V
mail – Mailbox:200
Msgs New: 3 Arch: 1
Lstn Greet LvMsg More>
Refer to Page 6
“Directory Dialing”
The Number of new messages in your mailbox is displayed on the “VM” Soft Key; you can access your
mailbox by pressing this key.
V
mail
–
Mailbox:200
Msgs New: 3 Arch: 1
Setup RcNam More>
V
mail
–
Mailbox:200
Msgs New: 3 Arch: 1
Page List Exit More>
Press “More” to switch Press “More” to switch
Number of New Left Messages
Soft Key
Indication Feature Next Operation after pressing Soft Key
Lstn Listen to Left Messages Press “Next” to play next message, press “Rplay” to repeat
played message, press “Del” to delete played message.
Press “More” for other Mailbox features.
Greet Mailbox Greeting Press one of “Gr1” / “Gr2” / “Gr3” to choose the desired
personal greeting message, and press “Lstn” (Listen) /
“Rec” (Record) / “Del” (Delete) to maintain it.
LvMsg Leave Message Start message recording and press “Done” to complete it.
Dial extension number you want to send this message and
press “Send”.
Setup Mailbox Option Menu Press “Code” (Security Code) / “Notfy” (Message
Notification) / “CallH” (Call Handling Option) / “ATime”
(Auto Time Stamp) to maintain each mailbox option.
RcNam Name Menu Press “Lstn” (Listen) / “Rec” (Record) / “Del” (Delete) to
maintain the Mailbox Name.
Page Page Message Menu Press “Lstn” (Listen) / “Rec” (Record) / “Del” (Delete) to
maintain the Paging Message.
List Message List Press “All” / “New” / “Arch” to set the message listen mode
(message list) which you want to listen.
Exit Exit VM Menu - - -

17
2-8 TUE 3:03PM
Check List
Menu Dir VM:00 CL:02
Total:05 New:02
Unans:03 Ans:02
All Unan Del Exit
01: 2142622999
2-6 13:19
Call Store Del More
Press “VOL Up /
Down” Keys to
select the
desired number.
0
1: 2142622999
2-6 13:19
Edit Back More
Press
“More”
to switch
Soft Key
Indication Feature Next Operation after pressing Soft Key
All All Incoming Calls List See below
Unan Unanswered Calls List See below
Del Delete List Press “Yes” to delete all
Caller-ID List. (or press
“No” to cancel)
Exit Exit from Summary - - -
Soft Key
Indication Feature Next Operation after pressing Soft Key
Call Call to displayed number Lift the handset to talk when the destination answered.
Store Store displayed number Press “STA” (Personal Speed Dial) or “Abb” (Common
Abbreviated Dial), and dial Bin Number to store the
displayed number with name. (Press Hold Key to save.)
Del Delete displayed number Next received Caller-ID shall be automatically displayed,
and continue the Caller-ID Soft Key operation.
Edit Edit displayed number Press “<-“ or “->” to change the cursor position, press “DEL”
to delete a digit, and dial new digit. (Press Hold Key to
save.) Press “CNCL” to cancel Edit Mode.
Back Return to Summary Continue the Caller-ID Soft Key operation.
Number of new unanswered calls is displayed on the “CL” Soft Key; you can access your Caller-ID List by
pressing this key.
“CL” Soft Key
Soft Keys Operation

18
Soft Key
Indication Feature Next Operation after pressing Soft Key
Dir Directory Dialing Refer to Page 6 for Directory Dialing operation.
Page Paging Press “InPg” (Internal Paging) or “ExPg” (External Paging), and
dial the Group/Zone number to page.
Pkup Call Pickup Press “Pers” for Extension Call Pickup.
Press “ExPg” for External Paging pickup.
Press “InPg” for Internal Paging pickup.
VM:00 Mailbox Access Refer to Page 16 (VM Soft Key).
Barg Barge-In Dial the target extension number to barge in.
Save Saved Number Dial Saved number is dialed automatically. Wait for answer.
2-8 TUE 3:03PM
Dir Page Pkup More
2
-
8
TUE 3:03PM
VM:00 Barg Save More
Press
“More”
to switch
Soft Key Operations during Off-Hook condition
Soft Keys Operation
When you press the Speaker Key or lift the handset you will see the following Soft Keys.
Soft Key Operations during Intercom Calling
2-8 TUE 3:03PM
Calling 216
MW Voice Rls More
2
-
8
TUE 3:03PM
Calling 216
VMsg Camp More
During Intercom calling (called party does not answer yet) you will see the following Soft Keys.
Press
“More”
to switch
Soft Key
Indication Feature Next Operation after pressing Soft Key
MW Message Waiting Message Waiting is set. Hang up to finish.
Voice
(Signal) Intercom Call Mode Switching (Signal / Voice) Signal -> Voice : Start to talk after beep tone.
Voice -> Signal : Wait for called party answer.
Press “Voice” (or “Signal”) again to switch Call Mode, if
necessary.
Rls Hang Up - - -
VMsg Leave a Message (In-Mail)
(Option) Start recording your message.
Camp Camp On / Callback Camp On
Wait for the system to call you back without hanging up.
Callback
Hang up and wait for the system to call you back.

19
LINE 03
Lnd Save Rls Acct
LINE 03
Park Trf More
L
INE 03
Conf Save Time More
L
INE 03
Rpt More
Soft Key
Indication Feature Next Operation after pressing Soft Key
Lnd Last Number Dialing Last dialed number is
dialed automatically.
Wait for answer.
Save Saved Number Dialing Saved number is dialed
automatically.
Wait for answer.
Rls Hang Up - - -
Acct Account Code Entry
(Option) Enter the Account Code.
When you seize a trunk for outgoing call, or you answered an incoming call, access following features using
Soft Keys.
After establishing
call and pass
4 seconds
Soft Key
Indication Feature Next Operation after pressing Soft Key
Lnd Last Number Dialing Last dialed number is dialed automatically. Wait for answer.
Park Park Hold Press “Sys” (System Park) or “StaP” (Extension Park) to select
type of Park Hold.
Trf Transfer Dial the desired extension number, or seize an idle trunk and
place a call to transfer.
Conf Conference Dial the desired extension number, or seize an idle trunk and
place a call to establish a conference. Press “Add” to invite the
other party, or press “Add” and “Begin” to start a conference.
Press “AnHd” to retrieve a held call.
Save Save dialed Number - - -
Time Call Duration Time
Indication Press “Time” again to turn off the Call Duration Time indication.
Rpt Repeat Dialing Repeat Dialing feature is set, and the system automatically
places a call periodically. Wait for answer.
Press
“More”
to switch
Soft Key Operations during Outside Call
(When you seize a Trunk)
Soft Keys Operation
2-8 TUE 3:03PM
Talking to 216
Conf
After establishing an Intercom call, access following feature using Soft Keys.
Soft Key Operations after establishing an Intercom Call
Soft Key
Indication Feature Next Operation after pressing Soft Key
Conf Conference Dial the desired extension number,
or seize an idle trunk and place a
call to establish a conference.
Press “Add” to invite the other
party, or press “Add” and “Begin”
to start a conference. Press
“AnHd” to retrieve a held call.
Refer to Page 12
“Conference”