Neptronic BBTHV1100A User manual

Actuator
Specification & Installation instructions
BT00/080619 1
BT100 BT105 BT120 BT200 BT205 BT220
Technical Data BBTHV1100A BBTHV1105A BBTHV1121A BBTHV1200A BBTHV1205A BBTHV1221A
Auxiliary switches No No Yes (2) No No Yes (2)
Feedback No Yes No No Yes No
Power supply 110 to 130 VAC 50/60Hz 220 to 250 VAC 50/60Hz
Power consumption 4 Watts at 120 VAC (0.166A AC) 7 Watts at 240 VAC (0.166A AC)
Control signal 3 wire / 2 position, 3 wire / 3 point floating
Running time through
90º 20 to 30 sec Torque dependant
Torque 50 in.lb. [5,6 Nm] at rated voltage
Electrical connection 18 AWG [0.8 mm2] minimum
Inlet bushing 2 inlet bushing of 5/8 in [15.9 mm] & 7/8 in [22.2 mm]
Angle of rotation 0 to 90 degrees, mechanically adjustable (factory set with 90º stroke)
Direction of rotation Reversible, Clockwise (CW) or Counterclockwise (CCW) (factory set with CW direction)
Ambient temperature -22ºF to +122ºF [-30ºC to +50ºC]
Storage temperature -22ºF to +122ºF [-30ºC to +50ºC]
Relative Humidity 5 to 95 % non condensing.
Weight 3 lbs. [1.4 kg]
Ingress protection IP22 equivalent to Nema type 2,
IP54 equivalent to Nema type 3R if water tight inlet bushings (not supplied NEP617) are installed
Warning: Do not press the clutch when actuator is powered
Dimensions
A
B
C
D
Dimension Inches Metric (mm)
A 1.50 38.1
B 3.26 82.8
C 6.60 167.5
D 3.01 76.4
Caution
We strongly recommend that all neptronic products be wired to a separate transformer and that transformer shall service only neptronic products. This precaution will
prevent interference with, and/or possible damage to incompatible equipment.
When multiple actuators are wired on a single transformer, polarity must be observed. Long wiring runs create voltage drop which may affect the actuator performance.
Old Number
BBTHV1100A BT100
BBTHV1105A BT105
BBTHV1121A BT120
BBTHV1200A BT200
BBTHV1205A BT205
BBTHV1221A BT220
Feature:
•Mounts easy on round
& square shaft (with option –8).
•Power supply high voltage 120 or 240 VAC.
•External clutch for manual adjustments.
•Maintenance free.
•Position indicator.
•Feedback
(on model 105 & 205).
•Auxiliary switches
(on model 120 & 220).

BT100/105/120/200/205/220 Specification & Installation instruction
2
Mechanical installation
CLUTCH
MOUNTING
BRACKET
1. Manually close the damper blades and positioned the
actuator at 0º or 90º.
2. Slide the actuator onto the shaft.
3. Tighten the nuts on the “U” bolt to the shaft with a 8mm
wrench to a torque of 60 in.lb. [6,7 Nm].
4. Slide the mounting bracket under the actuator. Ensure free
movement of the slot at the base of the actuator. The
bracket pin must be placed in the mid distance of the slot.
5. Fix the bracket to the ductwork with #8 self-tapping screws.
Wiring Diagrams Caution: Risk of electric shock. Remove power prior to connect.
3 wire / 2 position (ON-OFF)
LINE (+)
NEUTRAL (-) DRIVE CW
1 2 3
3 wire / 3 point floating
DRIVE CCW
LINE (+)
NEUTRAL (-) DRIVE CW
1 2 3
PC Board
Potentiometer
Only on model 105 & 205
1 2 3
Terminal
JP1
Rotation
direction
6 7 8
JP2
Feedback or switches terminal
Only on model 105, 120, 205 & 220
BBTHV1X00A
Rotation direction
CW
CCW
(0 to 90º)
(90 to 0º)
Stroke adjustment
To adjust the stroke, move the adjustment screws at the desired position.