Neptronic BT000S User manual

Actuator
Specification & Installation instructions
BT0S-210803 1
Technical Data
BT000S
BT005S
BT020S
BT060S
BT065S
BT080S
Auxiliary switches
-
-
2
(10° & 90°)
-
-
2
(10° & 90°)
Feedback
-
Yes
-
-
Yes
-
Fail safe - Enerdrive
-
Yes
Power consumption
6 VA
15VA Peak, 6VA
Control signal
3 wire / 2 position,
3 wire / 3 point floating
2 wire / 2 position,
4 wire / 3 point floating
Power supply
22-26 Vac or 24-32 Vdc
22-26 Vac or 28-32 Vdc
Running time through 90º
90 - 110 sec. (Fail-safe 20-35 sec)
Torque
50 in.lb. [5,6 Nm] at rated voltage
Electrical connection
18 AWG [0.8 mm2] minimum
Inlet bushing
2 inlet bushing of 13/16in [20.6 mm]
Angle of rotation
0 to 90 degrees, mechanically adjustable (factory set with 90º stroke)
Direction of rotation
Reversible, Clockwise (CW) or Counterclockwise (CCW) (factory set with CW direction)
Ambient temperature
-22ºF to +122ºF [-30ºC to +50ºC]
Storage temperature
-22ºF to +122ºF [-30ºC to +50ºC]
Relative Humidity
5 to 95 % non condensing
Weight
3 lbs. [1.4 kg]
Ingress protection
IP22 equivalent to Nema type 2,
IP54 equivalent to Nema type 3R if water tight inlet bushings (not supplied NEP617) are installed
Warning: Do not press the clutch when actuator is powered
Dimensions
Dimension
Inches
Metric (mm)
A
1.50
38.1
B
3.64
92.5
C
6.60
167.5
D
3.02
76.8
Caution
We strongly recommend that all Neptronic® products be wired to a separate transformer and that transformer shall service only Neptronic® products. This precaution will
prevent interference with, and/or possible damage to incompatible equipment.
When multiple actuators are wired on a single transformer, polarity must be observed. Long wiring runs create voltage drop which may affect the actuator performance.
1
Enerdrive System U.S.A. Patent #5,278,454
Features:
•Mounts easy on round
& square shaft (with option –8).
•External clutch for manual adjustments.
•Maintenance free.
•Position indicator.
•Fail safe by Enerdrive System1
(on model 060, 065 & 080).
•Auxiliary switches
(on model 020 & 080).
BT000S
BT005S
BT020S
BT060S
BT065S
BT080S

BT000S/005S/020S/060S/065S/080S
Specification & Installation instruction
2
Mechanical installation
1. Manually close the damper blades and positioned the
actuator at 0º or 90º.
2. Slide the actuator onto the shaft.
3. Tighten the nuts on the “U” bolt to the shaft with a 8mm
wrench to a torque of 60 in.lb. [6,7 Nm].
4. Slide the mounting bracket under the actuator. Ensure free
movement of the slot at the base of the actuator. The
bracket pin must be placed in the mid distance of the slot.
5. Fix the bracket to the ductwork with #8 self-tapping screws.
Wiring Diagrams
Models BT000S, 005S & 020S
Models BT060S, 065S & 080S
3 wire / 2 position (ON-OFF)
2 wire / 2 position (ON-OFF)
3 wire / 3 point floating
4 wire / 3 point floating
PC Board
Dip switch settings
Rotation direction (SW1)
CW
(0 to 90º) CCW
(90 to 0º)
Fail safe direction (SW2)
Fail safe
return at 0º Fail safe
return at 90º
Stroke adjustment
To adjust the stroke, move the adjustment screws at the desired position.
CLUTCH
MOUNTING
BRACKET
COMMON (-)
SUPPLY (+)
DRIVE
CW
1 2 3 4
DRIVE
CCW
TB1
COMMON (-)
SUPPLY (+) DRIVE CW
1 2 3 4
TB1
COMMON (-)
SUPPLY (+)
DRIVE
CW
1 2 3 4
DRIVE
CCW
TB1
COMMON (-)
SUPPLY (+)
DRIVE
CW
1 2 3 4
DRIVE
CCW
TB1
Potentiometer
Only on model 05S & 65S
BT060S
1 2 3 4
Feedback or switches terminal
Only on model 05S, 20S, 65S
& 80S
6 7 8
Terminal
TB3 TB1
SW2
Rotation direction
Fail safe direction
Only on model 60S,
65S & 80S
SW1