Neptronic BM200S User manual

Actuator
Specification & Installation instructions
BM200S(TRO)/080606 1
Technical Data BM200S
Power supply 220 to 250 VAC 50/60Hz
Ingress protection IP22 equivalent to Nema type 2,
IP54 equivalent to Nema type 3R if water tight inlet bushings (not supplied NEP617) are installed
Power consumption 6 VA
Torque 50 in.lb. [5,6 Nm] at rated voltage
Running time through 90º 90 - 110 sec
Electrical connection 18 AWG [0.8 mm2] minimum
Inlet bushing 2 inlet bushing of 5/8 in [15.9 mm] & 7/8 in [22.2 mm]
Control signal 2 to 10 VDC
Angle of rotation 0 to 90 degrees, mechanically adjustable (factory set with 90º stroke)
Direction of rotation Reversible, Clockwise (CW) or Counterclockwise (CCW) (factory set with CW direction)
Ambient temperature -22ºF to +122ºF [-30ºC to +50ºC]
Storage temperature -22ºF to +122ºF [-30ºC to +50ºC]
Relative Humidity 5 to 95 % non condensing.
Weight 3 lbs. [1.4 kg]
Warning: Do not press the clutch when actuator is powered
Dimensions
A
B
C
D
Dimension Inches Metric (mm)
A 1.50 38.1
B 3.26 82.8
C 6.60 167.5
D3.01 76.4
Caution
We strongly recommend that all neptronic® products be wired to a separate transformer and that transformer shall service only neptronic® products. This precaution will
prevent interference with, and/or possible damage to incompatible equipment.
When multiple actuators are wired on a single transformer, polarity must be observed. Long wiring runs create voltage drop which may affect the actuator performance.
BM200S(TRO)
Feature:
•Mounts easy on round
& square shaft (with option –8).
•External clutch for manual adjustments.
•Maintenance free.
•Position indicator.
•Output for thermostat TRO5405 supply

BM200S(TRO) Specification & Installation instruction
2
Mechanical installation
CLUTCH
MOUNTING
BRACKET
1. Manually close the damper blades and positioned the
actuator at 0º or 90º.
2. Slide the actuator onto the shaft.
3. Tighten the nuts on the “U” bolt to the shaft with a 8mm
wrench to a torque of 60 in.lb. [6,7 Nm].
4. Slide the mounting bracket under the actuator. Ensure free
movement of the slot at the base of the actuator. The
bracket pin must be placed in the mid distance of the slot.
5. Fix the bracket to the ductwork with #8 self-tapping screws.
Wiring Diagrams Caution: Risk of electric shock. Remove power prior to connect.
1
2 to 10 VDC INPUT
TB1
COMMON (-)
1 2
NEUTRAL
LINE
TB2
WITH
JUMPER
ON LEFT
JP1
TRO SUPPLY OUTPUT (+)
2 3
1
2
3
4
5
6
7
8
9
COM
24VAC
EXT.TS
NSB.INP
HT.RAMP
HT.RAMP.HD
CL.RAMP
CL.RAMP.HD
TPM
TRO5404
TERMINAL
PC Board
!!! HIGH VOLTAGE
1 2 3
Terminal for
thermostat
TRO5404
TB1
Rotation direction
SW1
Line voltage terminal
1 2
TB2
Potentiometer
N L
JP1
Control signal
selection
BM060VAV
Dip switch settings
Rotation direction (SW1)
CW
(0 to 90º)
CCW
(90 to 0º)
Stroke adjustment
To adjust the stroke, move the adjustment screws at the desired position.