Nevadent NAZ 2.4 C3 User manual

IAN 288765
ELECTRIC TOOTHBRUSH NAZ 2.4 C3
ELECTRIC TOOTHBRUSH
Operating instructions
ELEKTRISCHE ZAHNBÜRSTE
Bedienungsanleitung
ΗΛΕΚΤΡΙΚΗ ΟΔΟΝΤΟΒΟΥΡΤΣΑ
Οδηүίες χρήσης

GB/IE/NI/CY Operating instructions Page 1
GR/CY Οδηүίες χρήσης Σελίδα 15
DE/AT/CH Bedienungsanleitung Seite 29
Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of
the device.
Πριν ξεκινήσετε την ανάγνωση, ανοίξτε τη σελίδα με τις εικόνες και εξοικειωθείτε με όλες τις λειτουργίες
της συσκευής.
Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit allen
Funktionen des Gerätes vertraut.

B
A

GB│IE│NI│CY │ 1 ■
NAZ 2.4 C3
Contents
Introduction...................................................2
Intended use ..................................................2
Package contents ..............................................2
Appliance description ...........................................3
Technical data .................................................3
Safety information .............................................4
Set-up/fitting to the wall ........................................5
First use ......................................................5
Fitting/removing brush heads ....................................6
Operation ....................................................7
Brushing teeth .................................................7
Cleaning and maintenance ......................................9
Travel lock ....................................................9
Travel case...................................................10
Disposal .....................................................10
Ordering replacement parts ....................................11
Kompernass Handels GmbH warranty............................12
Service................................................................13
Importer ...............................................................13

■ 2 │ GB│IE│NI│CY
NAZ 2.4 C3
Introduction
Congratulations on the purchase of your new appliance.
You have selected a high-quality product. The operating instructions are part of
this product. They contain important information about safety, usage and disposal.
Before using the product, please familiarise yourself with all operating and safety
instructions. Use the product only as described and for the range of applications
specified. Please also pass these operating instructions on to any future owner.
Intended use
This appliance is intended exclusively for personal dental care at home. This
appliance is intended solely for use in private households. The appliance is not
intended for use in industrial or medical environments. It is not suitable for animal
care. Do not use it for commercial purposes.
Package contents
Handset
8 brush heads
Travelling case
Charger
2 screws
2 wall plugs
Operating instructions
NOTE
Check contents for completeness and damage immediately after un-
packing. Contact customer service if necessary.
Remove all packaging materials and plastic films from the appliance.

GB│IE│NI│CY │ 3 ■
NAZ 2.4 C3
Appliance description
Figure A:
1Brush head
2Drive shaft
3On/Off switch
4“Clean” LED (orange)
5“Sensitive” LED (green)
6“Massage” LED (yellow)
7Charge indicator
8Charger
9Drill holes
0Lid
qBrush holders
Figure B:
wTravelling case
eWall plugs
rScrews
Technical data
Power supply: 100–240 V ~ (AC), 50/60 Hz
Power consumption: 2 W
Rechargeable battery: Li-ion battery, 600 mAh, 3.7 V
Protection type (charger): IP X7 (protected against the ingress of water
during temporary immersion)
Protection class: II/
Charging time: approx. 14–16 hours (first charge)
Operating time: approx. 60 minutes (with fully charged battery)
Protection type (handset): IP X4 (protected against water splashes)

■ 4 │ GB│IE│NI│CY
NAZ 2.4 C3
Safety information
DANGER – RISK OF ELECTRICAL SHOCK!
► To avoid damage, do not allow liquids to penetrate the ap-
pliance and do not submerge it in water.
► Ensure that no foreign objects enter the appliance.
► In the event of malfunctions or obvious damage, please con-
tact our customer service department.
► Ensure that the power cable can never become wet or damp
during operation. Route the power cable in such a way that
it cannot become trapped or damaged in any other way.
Risk of electric shock!
► The mains cable of this appliance cannot be replaced. If the
cable is damaged, the whole appliance must be scrapped.
► Never touch the charger if it has fallen into water. Remove
the plug from the wall socket first! Risk of electric shock!
Do not immerse the handset or the charger in water or
other liquids.
WARNING – RISK OF INJURY!
► Toothbrushes may be used by children and by persons with
reduced physical, sensory or mental capabilities or lack
of experience and/or knowledge if they are supervised or
have been told how to use the appliance safely and are
aware of the potential risks.
► Cleaning and user maintenance should not be carried out
by children, unless they are under supervision.
► Do not allow children to play with the appliance.

GB│IE│NI│CY │ 5 ■
NAZ 2.4 C3
CAUTION – PROPERTY DAMAGE!
► The appliance may only be recharged with the supplied
charger.
Otherwise, the appliance could be irreparably damaged!
► Operate the appliance only with the original accessories
supplied.
Set-up/fitting to the wall
NOTE
In damp rooms, especially in the vicinity of water (bath), the charger 8
must be set up so that it cannot accidentally fall into the water.
Place the charger 8on a clean and level surface.
Ensure the charger 8cannot fall into water, such as a bath or sink.
You can also fit the charger permanently to the wall:
1) Mark two drill holes on the wall at a distance of approx. 44 mm from each
other. Check to ensure that there is a mains power socket in the immediate
vicinity.
2) Before drilling the holes, check to ensure that there are no electrical cables or
water pipes behind the markings.
3) Use a 5 mm drill bit to drill the marked holes and push the supplied wall
plugs ein.
4) Screw in the screws rso that the heads protrude a few millimetres. Hang
the charger 8 with the drill holes 9 over the two screws r and ensure
that the screws r slide into the slots. The charger 8should lie flush against
the wall. You can adjust the distance to the wall and compensate for any
unevenness in the wall by screwing or unscrewing the screws.
5) Hang the charger 8on the screwsr.
6) Ensure that the power cable is not trapped and that it lies properly in the
cut-out.
First use
NOTE
Before starting to use the appliance, check that it is in fault-free condi-
tion. You must not use the appliance if it has any faults.
1) Insert the power plug into the socket.
2) Before the first use, clean the new brush heads 1with clear water.

■ 6 │ GB│IE│NI│CY
NAZ 2.4 C3
3) Open the lid 0of the brush holders qand place the replacement brush
heads in the four slots provided. Close the lid 0again.
4) Place the handset on the charger 8so that it slides onto the pin on the
base.
5) Allow the handset to charge up for around 14–16 hours before using it for
the first time. The charging light 7on the front of the handset lights up red
during the charging process.
6) Use the handset repeatedly without charging the battery until the perfor-
mance becomes noticeably weaker or the toothbrush stops working and
the charge indicator 7flashes red. Then recharge the battery for 14–16
hours. When the appliance is fully charged, the charge indicator 7lights up
green.
7) Charge and discharge the toothbrush completely 3 times. The battery will
have then reached its full capacity.
8) You can now leave the handset in the charger 8after every use, so as to
always have full power available.
Fitting/removing brush heads
■ To remove the brush head 1, pull it upwards and off the drive shaft 2.
■ When fitting the brush head 1, ensure that the drive shaft 2on the handset
slides precisely into the socket on the brush head 1.
Push the brush head 1down until it completely covers the drive shaft 2.
NOTE
You can order replacement brush heads from our Service department
(see section "Ordering replacement parts").
You can also use the brush heads for the models NAZ 3.7 A1 and
DAZD 3.7 LI B2 (also available from Lidl).
The toothbrush is also compatible with brush heads from the following
Oral B©* models:
Oral-B Ortho, Oral-B Precision Clean, Oral-B 3D White, Oral-B Cross
Action, Oral-B Stages Power, Oral-B Sensitive, Oral-B Deep Cleaning.
*Oral-B is a registered trademark of Procter & Gamble.

GB│IE│NI│CY │ 7 ■
NAZ 2.4 C3
Operation
This toothbrush has 3 different power levels:
–“Clean”: normal speed, orange “Clean” LED 4
For cleaning the teeth.
–“Sensitive”: slow speed, green “Sensitive” LED 5
For cleaning the teeth if you have sensitive gums.
–“Massage”: slow speed with short breaks, yellow “Massage” LED 6
For massaging the gums.
■ Press the On/Off switch 3once to activate the “Clean” mode. The “Clean”
LED 4lights up.
■ Press once more to switch to “Sensitive” mode. The “Sensitive” LED 5lights up.
■ Press a third time to switch to “Massage” mode. The “Massage” LED 6
lights up.
■ To switch the toothbrush off, press the On/Off switch 3once more.
Brushing teeth
WARNING!
Due to the unaccustomed effect of the toothbrush, there may be some
initial gum bleeding. This is normal. If this continues for more than two
weeks, you should consult your dentist.
1) Place the brush head 1on the handset.
2) Moisten the brush under flowing water.
3) Put a little toothpaste onto the wet brush.
NOTE
To avoid spray, do not switch on the appliance until it is in your mouth.
4) Use the On/Off switch 3to select the desired operating mode.
NOTE
This toothbrush has a 30-second interval timer, so that all four jaw quad-
rants can be cleaned evenly.