Nidec Shimpo DT-5TS User manual

Instruction Manual
DT-5TXR / DT-5TS
DIGITAL PANEL MOUNT TACHOMETER
www.calcert.com [email protected]1.888.610.7664 0
5
10
15
20
25
30

2
Congratulations on your purchase of a Shimpo DT-5TXR
or DT-5TS digital panel mount tachometer. Whether
measuring RPM or a complex function, we trust you will
enjoy many years of professional results.
Please read the entire instruction manual thoroughly
before initial set-up and operation; the information
contained herein will aid in operating your Shimpo
DT-5TXR/DT-5TS panel meter safely and with excellent
results.
If you have any questions regarding our product(s), call
your local Shimpo representative or contact Shimpo
directly for assistance.
Contents
Standard Accessories................................................... 3
Features and Benefits ..................................................3
Important Safety Precautions...................................... 3
Display and Keypad...................................................... 4
Rear Panel and Terminals............................................. 5
Set-Up.......................................................................... 5
Power.....................................................................5
Sensor Connection..................................................5
Self-Test................................................................... 5
Panel Installation..................................................... 6
Factory Settings........................................................... 6
Parameter Settings..................................................6
Function Settings.................................................... 6
Operation....................................................................7
Mode Operation Selection...................................... 7
Setting Mode Parameters....................................... 7
Mode -01- (RPM or Rate Measurement) .............. 7
Mode -02- (Elapsed Time
Measurement/Monitoring).................................. 9
Mode -03- (Process Time Measurement)............ 10
“How to Operate” Teaching Feature .....................10
Setting High and Low Limits.................................11
Setting Functions..................................................11
Memory Feature.................................................... 12
Setting Examples................................................... 13
Modules Available for DT-5TXR...................................15
DT-5TXR with DOP-CPTR Module ...........................15
DOP-TRTR Module..................................................16
DOP-FVTR or DOP-FVC Module...............................16
DOP-BCD Module..................................................18
Dimensions and Specifications...................................19
Troubleshooting ........................................................ 20
Warranty....................................................................20
DT-5TXR
DT-5TS
www.calcert.com [email protected]1.888.610.7664 0
5
10
15
20
25
30

3
Important Safety PrecautionsStandard Accessories
If any damage is apparent, do not unpack the panel
meter. Notify the shipping carrier immediately for
damage claim instructions. Refer to the label to confirm
model number ordered and record serial number for
future reference.
Items included with the DT-5TXR or DT-5TS are:
•Mounting adapter, 2 pieces (attached)
•Mounting screw, 2 pieces (attached)
•Decal sheet
•Front button protective cover (attached)
Features and Benets
The DT-5TXR/DT-5TS panel meter offers many features and
benefits including:
•Accepts a wide range of ppr (1-9,999) to
accommodate any sensor commonly found in the
field
•Wide range of AC voltage input (85 – 264 VAC 50/
60 Hz) eliminates duplicity of models or changing
of transformers
•Scalable; able to measure in various units
•Standard 1/8 DIN mounting enables easy mounting
while saving time
•Accepts modules (DT-5TXR only) which provide
different types of outputs, i.e. analog voltage,
analog current (4-20 mA), relay closures (set points),
BCD output and others for
recording purposes or data analysis
Never use wet hands when connecting or
disconnecting a sensor or checking the unit.
Always use the correct voltage (AC type: 85-
264VAC, DC type: 9-35VDC).
Do not position the signal wires and power
cord near each other.
Remember to check terminal connections, as
they may become loose due to vibration.
Do not use or store unit in extreme
temperatures; normal operating temperature
is 32-113ºF (0-45ºC).
Do not use or store unit in oily, dusty, or high
humidity areas.
Do not use chemicals to clean the case; use a
damp, soapy cloth.
Do not operate the unit in a location where
electrical noise, static electricity or excessive
vibration is present.
Confirm that the unit is turned OFF when
connecting or disconnecting the unit to a
sensor.
www.calcert.com [email protected]1.888.610.7664 0
5
10
15
20
25
30

4
Display and Keypad
NOITCNUFNOITANGISED.ON
noitcnufyromemsetavitcAnottuByromeM.1
detavitcasinoitcnufyromemnehwNOrotacidnIyromeM.2
edomputesgnilacskciuQnottuBgnihcaeT.3
edomputesgnilacskciuqninehwNOrotacidnIgnihcaeT.4
putesretemaraproFnottuBretemaraP.5
putesnoitcnufroFnottuBnoitcnuF.6
snoitcnufs’retemarapsteSnottuBteS.7
noitcelesedoMnottuBedoM.8
lacedrofaerAlaceDtinU.9
tnemerusaemfostinusyalpsiDyalpsiDyramirP.01
11. Secondary Display B Secondary display
snoitcerrocrofecapskcaBnottuBecapskcaB.21
13. Negative Sign/Decimal Point Button Negative sign setting/decimal point shift
snoitcnufsuoiravroFnottuBciremuN.41
15. Secondary Display A Secondary display
tneserpsilangisnehwgniknilBrotacidnIlangiS.61
17. Comparator Indicator Indicates comparator condition
www.calcert.com [email protected]1.888.610.7664 0
5
10
15
20
25
30

5
Set-Up
Power
Refer to diagram 1 (right) for location of the terminals.
AC Models
Apply 85 – 264 VAC, 50/60 Hz between terminals 1 and 2.
DC Models
Apply 9 –35 VDC between terminals 1 (positive) and 2
(negative) on the main terminal block.
After proper power (AC or DC) is applied to the unit
and before any sensor is connected, the LED display
will light up.
Sensor Connection
Use the chart below to determine how to connect the
DT-5TXR/DT-5TS to Shimpo sensors:
diagram 1
Self-Test
To confirm that all display LEDs are operating correctly, a self-test is recommended (see “Display and Keypad” section
for button locations):
1. Press and hold the MODE button for approximately 3 seconds; “0” will begin flashing until “-01-” appears on the
display.
2. Press any of the lower buttons (NUMERIC, NEGATIVE SIGN/DECIMAL POINT, BACKSPACE) to scroll through “-02-”,
“-03-” and “-04-” until “-99-” appears on the display.
3. Press the SET button to begin the self-test. The entire display will cycle through all digits, arrows, dashes, colons,
decimal points, etc.
4. When satisfied that all LED’s are operational, press the SET button to exit.
SENSOR TYPE TERMINAL NUMBER FREQUENCY or RP M RANGE OPERATION TEMPERATURE FILTER
MPR000,5–0C06-B1ER
3–0C006-B1ER ,000 RPM
1–0C0001-B1ER ,800 RPM
zHk001)C°9.84+-°03-(F°021+-°22-zH052–0526-SCM
F°131+-F°31-zH333–0556-SCM
(
-25° - +55°C
)
100 kHz
MP-10 -40° - +221°F
(
-40° - +105°C
)
3030AN -100° - +225°F (-73° - +107°C)
3070A* -100° - +200°F (-73° - +104°C)
Contact Closure Relay or Solenoid Jumper 5 and 6 Connect 6, zH02zH02<9
BI2-S12 Open Collector NPN Proximity 4,6, F°851+-°31-zHk2–09 (-25° - +70°C) 100 kHz
zHk03)C°07+-C°02-(F°851+-F°4-zHk8–09,7,4ytimixorPgnihctiwSeriw-3G-ES
zHk01)C°06+-°55-(F°041+-°86-zHk1–08,4ytimixorPgnihctiwSnoNeriw-2G-2JD
* For hazardous locat ions
10 kHz
Retro-Reflective
Magnetic
Rotary Pulse Generator 30 kHz
3,8,9
)C°05+-°01-(F°221-°419,7,4
4,6,9
Rear Panel and Terminals
NO.DESIGNATION
1. Lower Module Latch
2. Upper Module Latch
3. Lower Module Connector
4. Upper Module Terminal Block
5. Rear Cover
6. Main Terminal Block
www.calcert.com [email protected]1.888.610.7664 0
5
10
15
20
25
30

6
Factory Settings
The following charts reflect the default parameter and function settings as programmed by the factory:
Operating Mode -01- (RPM or Rate Measurement)
Panel Installation
Install the DT-5TXR/DT-5TS on panel as follows:
1. Confirm that the panel thickness is 0.047” - 0.197” (1.2 mm - 5 mm).
2. Remove the two mounting adapters (provided) from the DT-5TXR/DT-5TS (diagram 2).
3. Install a water-resistant gasket on the panel (see diagram 3 & 4).
4. Hold the panel meter in a horizontal position, insert it into the cut-out and press against gasket (diagram 5).
5. Replace the two mounting adapters (diagram 6).
6. The DT-5TXR/DT-5TS is secured on the panel by using the two mounting screws (provided) (see diagram 7).
3margaid2margaid
7margaid6margaid5margaid
diagram 4
DISPLAY
1 Pulses
p
er revolution
_ _
0001 1
pp
r
2 Sensing RPM _01000 1,000 RPM
3 Display units 10001,000
4 Update time _1.0 _1 second
5 Display “Hold” after input signal ceases
_ _
006.06 seconds
6 In
p
ut filter
_
10
_
10 kHz
DEFAULT FACTORY SETTING
PARAMETER DESCRIPTION
DISPLAY
MEANING
1 The 2nd HI and 2nd LO limitsetting 0 0 0 0 0 0 0
2 Hysteresis of 1st HI and 1st LO set _ _ _ _ 0 0 0
3 Secures the 1st HI and 1st LO set
_
0
_
Not secured
4 Out
p
ut activation of an
y
set limit
_ _ _ _
0 0 0 seconds
5 Selection of secondar
y
dis
p
la
y
_
0
_
1st HI and 1st LO limit set
6 Main display shows 0 below this no. setting 0 0 0 0 0 0 0
7 Av er ages the sensor output fr equency _0 _None
8 Deceleration to ZERO display value _0 _Off
10 Logic of BCD output _0 _Negative-true logic
11 Analog output value 0 0 1 0 0 0. 1000
12 Minimum value of analog output 0 0 0 0 1 0. 10
13 Update time for analog output
_
0
_
About 10 msec
14 Offset for analo
g
out
p
ut
_
0 0 0.0 0%
DEFAULT FACTORY SETTING
Output modules (DT-5TXR only)
FUNCTION DESCRIPTION
MEANING
www.calcert.com [email protected]1.888.610.7664 0
5
10
15
20
25
30

7
Operation
Mode Operation Selection
Depending upon the type of application, the DT-5TXR/DT-5TS offers different modes of operation; these modes and
their functions are:
Select the mode of operation as follows:
1. Press and hold the MODE button for approximately 3 seconds; “0” will begin flashing until one of the five modes
(see table above) appears on the display.
2. Each time one of the lower buttons (NUMERIC, NEGATIVE SIGN/DECIMAL POINT, BACKSPACE) is pressed, the
display will scroll through these modes as indicated below:
3. Press the SET button to store the mode of operation and exit.
MODE NOITCNUF
-01- RPM or rate measurements
-02- Ela
p
sed time measurin
g
/ monitorin
g
-03- Process time measurement
-04- Flow rate measurement
(
used onl
y
in Ja
p
anese market
)
-99- Self-test
(
see “Self-Test” section under “Set-U
p
”
)
Setting Mode Parameters
Modes-01-,-02-and -03-have several parameters that must be selected and programmed into the DT-5TXR/DT-5TS.
In addition, there are also function settings to further customize the DT-5TXR/DT-5TS.
NOTE: Because the flow rate measurement mode (-04-) is only used in the Japanese market, it is not covered in this
manual. Contact Shimpo for additional information if necessary.
NOTE: If a mistake is made entering any number, simply press the BACKSPACE button to erase the last digit on the
primary display.
Mode -01- (RPM or Rate Measurement)
The following parameters must be set in mode -01-so that the DT-5TXR/DT-5TS will display the correct readings:
DISPLAY MEANING
9999-1noituloverrepsesluP1 _ _ 0001 1 ppr
2 Sensing UMPR p to 9999 9 _010001000 RPM
00010001999999–10000.0stinuyalpsiD3
4 Update time 0.2, 0.5, 1.0, 2.0, 5.0, 10, 1 5, 30, 60 seconds
_
1.0
_
1 second
5 Display “ Hold” after input signal ceases 0.1 – 150 seconds _ _ 006.0 6 seconds
zHk20.0,001,03,01retliftupnI6
_
10
_
10 kHz
FACTORY SETTING
RANGEDESCRIPTIONPARAMETER
www.calcert.com [email protected]1.888.610.7664 0
5
10
15
20
25
30

8
Mode -01- (RPM or Rate Measurement) continued
Set the parameters in mode -01-as follows:
1. Press the PAR button; the display will indicate:
The “-01- P01” on secondary display A indicates that
the meter is in the RPM mode (-01-) and parameter 1
is showing on the primary display (1 ppr [factory
setting]).
2. Using the NUMERIC buttons, enter the number of
pulses per revolution produced by the sensor being
used (1-9999). For example, if a rotary pulse
generator has an output of 60 ppr, then 6 0 would
have to be entered.
3. Press the PAR button; the display will reflect:
The secondary display A reflects that the meter is
still in mode -01-, but parameter 2 is showing on the
primary display (1000 RPM [factory setting]).
4. Using the NUMERIC buttons, enter the number of
RPM that must be monitored (up to 99999). For
example, if the motor to be monitored has a speed
of 1,750 RPM, then 1 7 5 0 would have to be entered.
5. Press the PAR button; the display will show:
As the secondary display indicates, parameter 3 is
reflected on the primary display (1000 [factory
setting]).
6. Use the NUMERIC buttons to enter the value of the
display as it relates to the already programmed RPM
setting. For example: if the desired display reading
is feet per minute and the belt that is being measured
is moving at a rate of 55.5 f/min, then 5 5 5 would
have to be entered and the negative/decimal point
button pressed once. If the desired reading is RPM,
then the same 1 7 5 0 would have to be entered.
7. Press the PAR button; the display will reflect:
Parameter 4 is now showing on the primary display
(1.0 second [factory setting]).
8. Use any of the lower buttons to scroll through the
update times (see table under “Setting Mode
Parameters” on page 7) until the desired reading is
displayed.
9. Press the PAR button, the display will indicate:
The primary display is now reflecting parameter 5
(6 sec [factory setting]).
10.Press the NUMERIC buttons to enter the value in
seconds that the display should hold the final reading
after the input signal ceases.
11. Press the PAR button; the display will reflect:
Parameter 6 is showing on the primary display (10
kHz [factory setting]).
12. Refer to the “Connection of Sensors” chart under
the “Set-Up” section for the proper filter for the
sensor being used. Press any of the lower buttons
to scroll through the input filters (see table under
“Setting Mode Parameters” on page 7) until the
desired reading is showing.
13. Press the SET button to store the parameter settings
and exit.
NOTE: Please see page 13 for an example of MODE -01-
operation.
www.calcert.com [email protected]1.888.610.7664 0
5
10
15
20
25
30

9
Mode -02- (Elapsed Time Measurement/Monitoring)
The following parameters must be set in mode -02-so that the DT-5TXR/DT-5TS will display the correct readings:
Except for parameter 3, the instructions are the same for setting the parameters as in mode -01-.
Instructions for setting the parameters in mode -02-are as follows:
1. Press the PAR button.
2. Use the NUMERIC buttons to enter the number of pulses per revolution.
3. Press the PAR button.
4. Press the NUMERIC buttons to enter the sensing RPM.
5. Press the PAR button; the display will reflect:
The secondary display A reflects that the meter is in mode -02-, but parameter 3 is showing on the primary
display (10 sec [factory setting]).
6. Use the NUMERIC buttons to enter the number of seconds to the hundredth place (000.00).If time in hours,
minutes, and seconds is necessary, press the NEGATIVE/DECIMAL POINT button, then use the NUMERIC buttons
to enter the amount of time as it relates to the already programmed RPM setting.
7. Press the PAR button.
8. Use any of the lower buttons to scroll through (see table above) and select an update time.
9. Press the PAR button.
10.Use the NUMERIC buttons to enter the time in seconds that the display should hold in the final reading.
11. Press the PAR button.
12. Refer to the “Sensor Connection” table under the “Set-Up” section for the proper filter for the sensor being
used. Press any of the lower buttons to scroll through the input filters (see table above) until the desired reading
is showing.
13. Press the SET button to store the parameters and exit.
NOTE: Please see page 13 for an example of MODE -02-.
DISPLAY MEANING
1 Pulses
p
9999–1noituloverre
_ _
0001 1
p
/r
2 Sensin
g
UMPR
p
to 99999
_
010001000 RPM
a)Hours, Minutes, Seconds
0 : 00 : 00 – 9 :59 : 59
b)Seconds
0 : 00 – 999 : 99
4 Update time 0.2, 0.5, 1.0, 2.0, 5.0, 10 , 15, 30, 60 second
s
_1.0 _ 1 second
5 Display “Hold” after input signal ceases 0.1 – 150 seconds
_ _
006.06.0 seconds
6 In
p
01retliftu
,
30
,
100
,
0.02 KHz 10 10 kHz
10.0 secondsDisplay units3 _010 : 00
FACTORY SETTING
RANGEDESCRIPTIONPARAMETER
www.calcert.com [email protected]1.888.610.7664 0
5
10
15
20
25
30

10
Mode -03- (Process Time Measurement)
The following parameters must be set in mode -03-so that the DT-5TXR/DT-5TS will display the correct readings:
Instructions for setting parameters in mode -03-are as
follows:
1. Press the PAR button; the display will indicate:
The secondary display A shows that the meter is in
mode -03-, and parameter 1 is showing that the
primary display will count in hundredths of a second
(000.00).
2. Use any of the lower buttons to toggle between
the meter reading in seconds or reading in hours,
minutes, and seconds (see table above ).
3. Press the PAR button; the display will indicate:
Parameter 2 is showing on the primary display
(1 [factory setting]).
4. The input signal edge can be triggered by the leading
edge (1) or trailing edge (0). Press any of the lower
buttons to toggle between these two settings (see
table above).
5. Press the PAR button; the display will reflect:
“How to Operate” Teaching Feature
NOTE: This feature can only be used in mode -01-.
With the DT-5TXR/DT-5TS it is possible to monitor the speed
of a motor when the number of pulses that the sensor is
generating is unknown. The RPM can be programmed
into the meter if it is already known or discovered by
using a handheld tachometer (Shimpo models DT-105A
or DT-107A for contact measurement; DT-205LR or DT-207LR
for non-contact measurement). The meter will then use
this number to set parameters 1 and 2.
Set the teaching feature as follows:
1. Determine the output RPM.
2. Confirm that the meter is receiving a signal from the
sensor (the SIG indicator will be illuminated).
3. Press the TEA button (the TEA indicator will be
illuminated).
4. Use the NUMERIC buttons to enter the known RPM.
5. Press the SET button to save the setting.
The parameters for mode -03-are completely different for those of mode -01-and mode -02-.
The primary display is now showing parameter 3
(3600 sec [factory setting]).
6. Use the NUMERIC buttons to enter the amount of
time in seconds that the display needs to hold the
measured process.
7. Press the PAR button; the display will indicate:
Parameter 4 is showing on the primary display (10kHz
[factory setting]).
8. Refer to the “Connection of Sensors” chart under
the “Set-Up” section for the proper filter for the
sensor being used. Press any of the lower buttons
to scroll through the input filters (see table above)
until the desired reading is showing.
9. Press the SET key to save these parameter settings
and exit.
NOTE: Please see page 14 for an example of MODE -03-.
DISPLAY MEANING
Hours, minutes, seconds 00:00:00
or or
Hundreds of a second 0:00
0 = Trailin
g
ed
g
e
1 = Leading edge
3 Auto zero time 0.1 – 3,600 seconds _3600.03600 seconds
4 Filter 10, 0.02 kHz _10 _10 kHz
FACTORY SETTING
RANGESETTINGPARAMETER
2
dnoces001/11 0:00
_1_ Leading edgeInput signal edge
www.calcert.com [email protected]1.888.610.7664 0
5
10
15
20
25
30