Nidek Medical TONOREF II Manual

AUTO REF/KERATO/TONOMETER
Model TONOREF II
NETWORK SETTING MANUAL
March, 2009
XRKT2*RDA002A/E

NIDEK CO., LTD. : 34-14, Maehama, Hiroishi-cho, Gamagori, Aichi 443-0038, Japan
(Manufacturer) Telephone: [phone]
Facsimile: 81-533-67-6610
NIDEK CO., LTD : 3F Sumitomo Fudosan Hongo Bldg., 3-22-5, Hongo,
(Tokyo Office) Bunkyo-Ku, Tokyo 113-0033, Japan
Telephone: [phone]
Facsimile: 81-3-5844-2642
NIDEK INCORPORATED : 47651 Westinghouse Drive, Fremont, California 94539, U. S. A.
(United States Agent) Telephone: [phone]
Facsimile: 1-510-226-5750
NIDEK SOCIETE ANONYME : Europarc 13, rue Auguste Perret, 94042 CRETEIL, France
(EU Authorized Representative) Telephone: [phone]
Facsimile: 33-1-49 80 32 08

1
: OUTLINE OF THIS MANUAL
XRKT2*RDA002A/E
1 OUTLINE OF THIS MANUAL
This manual describes the connection method to the PC via LAN connection for the TONOREF II.
In this manual, the procedures to replace the circuit board of devices that do not support LAN connec-
tion, to upgrade programs (V1.06 or earlier to V1.07 or later), and to perform LAN connection settings
are also described.
Perform the following work only for devices that do not support LAN connection.
• Replacing 15601-EA01 (primary power supply)
See “3 REPLACEMENT OF EA01” (page 3).
• Program upgrade
See “4 SOFTWARE UPGRADE” (page 5).
Serial numbers for models requiring EA01 replacement and program upgrade
The following work must be performed to all devices.
• Connection of equipment and cables
See “5 DEVICE CONNECTION” (page 7).
• Setting of the receiver PC
See “6 CONFIRMATION AND SETTING OF RECEIVER PC” (page 9).
• Network setting of the TONOREF II
See “7 CONFIRMATION AND SETTING OF DEVICE” (page 12).
N. Inc. Outside Japan
- 720430 to 731586 (except
for 731517)

2
: LAN CONNECTION XRKT2*RDA002A/E
2 LAN CONNECTION
It becomes possible to transfer TONOREF II measured data to the PC via network. By transferring
measured data to the PC, data management is possible utilizing various types of database software.
2.1 Basic Communication Specifications
Network settings such as IP address and file sharing for any connected PC are required. Under
approval of the network administrator of the facility, set parameters of the device and PC.
Basic specifications CIFS (file sharing with PC)
Connector RJ-45
Standard 10/100 Base-TX
Cable Straight
Operating systems Windows2000, XP, Vista
CAUTION
• Since parameters will be changed, print out the parameters to keep until the work is
complete so that they can be restored manually should problems occur.

3
: REPLACEMENT OF EA01
XRKT2*RDA002A/E
3 REPLACEMENT OF EA01
Replace 15601-EA01 (primary power supply) with the LAN support board.
1 Put the device on a stable table.
2Push the main body to the side on which it will
be laid and secure it using the locking lever,
then gently lay the device on its side.
3Unscrew BS3×6 (n = 4) to remove the base
plate (30601-M002).
4Unscrew BS3×8 (n = 3) to remove the inlet
ASSY (15601-1100).
5Unscrew BS3×8 (n = 1) to disconnect the
EA01 ground wire.
$5 


$5 



4
: REPLACEMENT OF EA01 XRKT2*RDA002A/E
6Unscrew BS3×8 (n = 4), remove the switching
power supply (80602-00102), then disconnect
the P001 connector.
7Unscrew FC3×6 (n = 4), then remove the
BA05 board (15601-BA05) to replace 15601-
EA01 with the LAN support board.
8Reassemble the parts in the reverse order.
9Peel off the masking sticker (LAN connector
side) attached on the underside.
$5 



EA01
4
FC3×6
BA05
Masking sticker

5
: SOFTWARE UPGRADE
XRKT2*RDA002A/E
4 SOFTWARE UPGRADE
1 Save the upgrade program to a USB flash drive.
Upgrade software
RKT2_softwrite_V***.mot (V 1.07 or later)
The latest program is written in the CD-R of the RKT-2 upgrade kit (32106-0600).
If more than three upgrade files are attempted to
be saved, the fourth and other later files are not
recognized. Only save up to three files.
When saving upgrade files to the USB memory,
save in the root directory, not in a created folder.
2Turn off the device.
3Connect the USB flash drive (32166-E340) to the USB A connector of the main body.
4Turn on the device.
5When two or more upgrade files are saved in the
USB flash drive (32166-E340), the file select
screen appears.
Only when two or more upgrade files are saved,
the file select screen appears.
6Press the file to be upgraded.
• When parameters have been set by customers, print the parameter settings in advance so
that they can be restored.
%#0%'.
8
8
8
5'.'%6(+.'

6
: SOFTWARE UPGRADE XRKT2*RDA002A/E
7The upgrade confirmation screen appears.
8Press OK.
9The screen shown to the right appears and
upgrade starts.
10 When upgrade is complete, the screen shown to the
right appears. Turn off the power.
11 Remove the USB flash drive from the device.
12 Turn on the power and confirm that the device starts
properly.
If the upgrade was failed, start from step 1 again.
13 Set the NETWORK parameters.
%#0%'.
1-
51(694+6'/1&'
8GT
51(694+6'/1&'
8GT
4'#&+0) 94+6'
51(694+6'%1/2.'6'
219'41((4'/8'75$
8GT
4'#&+0) 94+6'

7
: DEVICE CONNECTION
XRKT2*RDA002A/E
5 DEVICE CONNECTION
5.1 Connecting LAN Cables
Connect the LAN cable to the LAN connector on the underside of the device.
Connect the other end of the LAN cable to the HUB connected to the receiver PC.
5.2 Connecting the Barcode Scanner/ Magnetic Card Reader
Turn off the main body and then connect the barcode scanner or magnetic card reader to the USB-A
connector on the underside of the device.
Available barcode scanner/ magnetic card reader
Barcode scanner
Magnetic card reader
CAUTION
• Be sure to connect to the PC via a network hub (HUB).
Do not connect to the PC directly. A connection failure may occur.
TONOREF II Receiver PC
LAN cable
Network hub (HUB)
CAUTION
• Do not connect or disconnect cables while the main body power is on.
An error may result.
19701-E006 USB barcode scanner (OPL-5850-USB, ROLAN)
36120-E122 USB barcode scanner (USBee-1000, WELCOM DESIGN)
14631-E001 ( Option for US-4000) Magnetic stripe card reader (MS240-2U MSR track I, II, UNITEK
JAPAN)

8
: DEVICE CONNECTION XRKT2*RDA002A/E
5.3 System Diagram Example
The diagram shown below illustrates the connection of an actual system.
The system diagram below is only an example. It may be changed significantly depending
on the connection network scale. To confirm the system diagram, contact the network
administrator of the facility.
Server Hub
Hub Hub
Hub
ARK-530A / NT-530 TONOREFII Other examination room,
operating room, or such
Connected devices
Slit lampClinic
IP ADDRESS: 10.50.XXX.YYY
SUBNET MASK: 255.255.255.0
䋪XXX, YYY : 0 to 255
(Set by the facility administrator to avoid repeated IP address in the network.)
Examination room
IP ADDRESS: 10.50.XXX.YYY
SUBNET MASK: 255.255.255.0
IP ADDRESS: 10.50.XXX.YYY
SUBNET MASK: 255.255.255.0
Receiver
terminal PC
IP ADDRESS: 10.50.XXX.YYY
SUBNET MASK: 255.255.255.0 IP ADDRESS: 10.50.XXX.YYY
SUBNET MASK: 255.255.255.0