Nidek Medical OT-6020 User manual

OPHTHALMIC REVOLVING
REFRACTION STAND
O
O
O
T
T
T
-
-
-
6
6
6
0
0
0
2
2
2
0
0
0
OPERATOR’S MANUAL

Before use or maintenance, read this manual.
This Operator’s Manual contains information necessary for correct and effective operation of NIDEK
ophthalmic revolving refraction stand OT-6020, and provides procedures for operation, cautions,
specification, and procedures for maintenance.
The unit complies with European standards 93/42/CEE for medical devices. This manual is necessary for
proper use. Especially, the safety precautions and operating procedures must be thoroughly understood
prior to operation of the unit. Keep this manual handy for reference.
There are no user-serviceable parts inside the unit except fuses and relays.
Therefore, if you encounter any problems or have questions about the unit during the operation, please
contact NIDEK or your authorized distributor.

Ref : Operator's manual OT-6020 2006-07.doc 3
TABLE OF CONTENTS
1OT-6020’S RANGE 4
1.1 PRESENTATION OF THE OPHTALMIC STAND 4
1.2 THE VARIOUS VERSIONS 4
1.3 CLASSIFICATION 5
2SAFETY 6
2.1 CAUTIONS IN INSTALLATION 6
2.2 ELECTRICAL CONNECTION 6
2.3 RECOMMENDATIONS FOR USE 7
2.4 CLEANING 7
2.5 LABELS 7
3STAND’S DESCRIPTION 8
3.1 GENERAL VIEW 8
3.2 DETAILED VIEWS 9
4USE 10
4.1 POWER ON 10
4.2 POWER OFF 10
4.3 USE OF THE CONTROLS 10
4.4 LOW VOLTAGE PANEL 11
5TROUBLESHOOTING GUIDE 12
6MAINTENANCE 15
6.1 REPLACING FUSES 15
6.2 REPLACING BULBS 15
6.3 CLEANING 15
6.4 LIST OF SPARE PARTS 15
7TECHNICAL FEATURES 16
7.1 MAIN FEATURES 16
7.2 ELECTRIC DIAGRAM 16
7.3 DIMENSIONS 16

Ref : Operator's manual OT-6020 2006-07.doc 4
1 OT-6020’S RANGE
1.1 PRESENTATION OF THE OPHTALMIC STAND
The revolving consultation unit OT-6020 is used to perform ophthalmic examination with the greatest
efficiency and in the best possible conditions.
Numerous possibilities allow you to configure your consultation unit according to your wishes:
OT-6020 is available with manual or electric rotation, with 3 or 4 pull-out flaps, with patient chair with fixed or
reclining backrest, with lighting column with projector support, with 2 models of refractor arms.
You can also arrange your work place with a full range of desks specially designed for this consultation unit.
1.2 THE VARIOUS VERSIONS
OT-6020 with laminated wood plated table top, mass dyed, with
A small desk
A patient chair with adjustable backrest
3 instruments+ refractor on a pivoting arm with bend for near vision
1 refraction cabinet with a trial lenses case for 232 lenses
1 lighting column matching with the colour of the unit.
OT-6020 with gloss paint coated table top, with
A large desk
A patient chair with reclining backrest
3 instruments+ refractor on an electrically translating arm
1 drawer for trial lenses in the table top
1 lighting column in aluminium

Ref : Operator's manual OT-6020 2006-07.doc 5
1.3 CLASSIFICATION
Classification under the provision of 93/42/EEC (MDD)
The ophthalmic unit OT-6020 is classified as Class I system.
Form of protection against electric shock Class I
A Class I is a unit in which the protection against electric shock does not rely on basic insulation only, but
which includes an additional safety precaution in such a way that means are provided for the connection of
the unit to the protective (ground) conductor in the fixed wiring of the installation in a way that accessible
metal parts cannot become live in the event of a failure in the basic insulation.
Use a power outlet which is equipped with a grounding terminal.
Degree of protection against electric shock
The ophthalmic unit OT-6020 is classified as a device with a Type B Applied Part.
A Type B Applied Part provides a particular degree of protection against electric shock, particularly regarding
the following:
Allowable leakage current
Reliability of the protective earth connection (if present)
Degree of protection against ingress of liquids
The ophthalmic unit OT-6020 is classified as IP20 (in accordance with IEC 60529).
The OT-6020 is an ordinary device, as such does not provide protection with respect to harmful effects due
to the ingress of water although it is protected against access to hazardous parts with a solid matter such as
a finger of 12.5 mm in diameter.
Avoid exposing water to the device.
Mode of operation
Classification of the ophthalmic unit OT-6020: continuous operation.

Ref : Operator's manual OT-6020 2006-07.doc 6
2 SAFETY
The following safety precautions should always be followed. The safety word PRECAUTION
indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury or
property damage accident. Even situation indicated by PRECAUTION may result in serious injury
under certain conditions. Safety precautions must be strictly followed at all times.
2.1 CAUTIONS IN INSTALLATION
PRECAUTION
Install the ophthalmic unit in a place that will never be exposed to water. If water gets into the internal
structure of the unit, electric shock or unit malfunction may result.
The installation location must satisfy the following environmental conditions:
Place with low dust content
Flat floor, without waves of more than 5 mm,
Stable, level place that is free from vibration or shock
Floor supporting the weight of the unit,
If these environmental conditions are not satisfied, the unit could fall over, the floor could get damaged
and it may result in some serious injuries.
Do not carry alone the ophthalmic unit. Injury, unit damage, damage of medical devices placed on the
table top may result if the unit is carried by one person.
This unit has been tested and found to comply with the limits for medical devices to the
IEC 60601-1-2. These limits are designed to provide reasonable protection against harmful interference
in a typical medical installation.
2.2 ELECTRICAL CONNECTION
PRECAUTION
Be sure to use an outlet equipped with a grounding terminal which meets the specified power
requirements. If not, the unit may not deliver full performance, or malfunction or fire may result. In
addition, if the outlet is not equipped with a grounding terminal, there is a fear of electrical shock or fire in
the event of a power leak.
Securely connect the mains plug into an outlet. Insecure connection may result in fire
To disconnect the mains plug, hold it. If the power cord is pulled out, short circuit or electric shock may
result in a case of break in the wires inside the power cord.
Never put heavy objects on the power cord nor catch the cord between any objects. The cover of the
power cord may become worn and fire or electric shock may result.
If the metal core of the power cord is exposed, if the power turns on and off by shaking the power cord, if
cord or plug gets so heated that one cannot hold it, it means that the power cord is damaged. Contact
NIDEK or your authorized distributor to replace it immediately. Electric shock or fire may result.
Wipe between the prongs of the mains plug with a dry cloth occasionally. If dust settles between the
prongs, the dust easily takes up moisture, and short circuit or fire may result.
If the ophthalmic unit will not be used for a long time, disconnect the power cord from the wall outlet. Fire
may result.

Ref : Operator's manual OT-6020 2006-07.doc 7
2.3 RECOMMENDATIONS FOR USE
PRECAUTION
Do not use the unit for other than the intended purpose. NIDEK is not responsible for accidents or
malfunction caused by misuse.
Never disassemble nor touch the inside of the unit. Electric shock or unit malfunction may result.
If a failure in the unit cannot be solved by fuse replacement or power switch turning on, do not touch the
inside of the unit. Disconnect the power cord from the outlet and contact NIDEK or your authorized
distributor.
2.4 CLEANING
When parts become dirty, wipe with a dry and soft cloth. For stubborn dirt, immerse the cloth in a neutral
detergent, wring well, and wipe. Finally wipe with a dry and soft cloth. Never use an organic solvent such
as paint thinner to wipe off the exterior. This may ruin the surface.
The room lamp on the top of the aluminium lightning column can be dismounted for easy cleaning
operation. Before cleaning, glasses of room light must be totally cold, or injury such as burns or
breakages may result.
Service work should be performed only by service persons authorized by NIDEK. NIDEK is not
responsible for any accidents resulted from improper servicing.
2.5 LABELS
The following label is affixed to draw the operator’s attention.
Refer to the operator’s manual prior to
operation or maintenance.
Protection against electric
shock is of a type B
Applied Part.
(grounding connection)

Ref : Operator's manual OT-6020 2006-07.doc 8
3 STAND’S DESCRIPTION
3.1 GENERAL VIEW
Electrically
translating arm for
refractor
Room lamp
Patient chair
Electrical height adjustment (16 cm
of adjustment), 150kg loading
capacity)
360° rotation
2 different devices:
FE1001 fixed backrest and
adjustable height from 45 to 61 cm
FE2001 170° reclining backrest and
adjustable height from 48 to 64 cm
Li
g
ht for near vision
Bracket for chart
projector
Table top
Electrical or manual rotation.
lectrical adjustment from 76 to 89cm.
Combined with the patient chair, the
it is designed for comfortable
examination either of adults or children.
It can hold up to 4 instruments and the
refractor.
Safety levers integrated under the
tables to avoid crushing the patient’s
legs by moving either the chair up or
the table down.
E
un
Brake release pedal
Forth and back
adjustment of the
instrument according
to the patient
stoutness.
Control panel
Electrical cabinet
cover
(See § 2.3
« Recommendations
for use
»)
Refraction cabinet
Fuses
Thermal fuse circuit
breaker (green light
indicator for voltage)
Pull-out flap

Ref : Operator's manual OT-6020 2006-07.doc 9
3.2 DETAILED VIEWS
Refractor arm
Manually pivoting model, with
reclining for near vision
Refraction cabinet with trial lenses
case (large set) on the door Trial lenses case (large set) incorporated in
a drawer of the table top
Opening and closing
by a single switch
Pull-out flap

Ref : Operator's manual OT-6020 2006-07.doc 10
4 USE
4.1 POWER ON
The ophthalmic unit must be properly connected to a wall outlet (seer § 2.2 « Electrical
connection »): the green lamp of the circuit breaker is on. Then, press the circuit breaker button to
position « I ».
A press on the « ON » white button of the control panel switches the unit on, and all control buttons
get illuminated. For the electric rotation model, initializing sequence of table top starts, and brings it
automatically to position 1.
4.2 POWER OFF
Your ophthalmic unit shall be powered off daily. Press the « OFF » red button of the control panel (control
buttons light off) and press the circuit breaker button to the position « O ». Only the green lamp of the circuit
breaker remains illuminated.
4.3 USE OF THE CONTROLS
OPTIONAL CONTROLS
For the lighting of the cabinet
(toggle switch)
ELECTRIC ROTATION
Each button brings a pull-
out flap ready to be pulled
out for examination
LAMP
Spot
ON
OFF
LAMP
Room
TABLE
Up / Down
SEAT
Up / Down
OPTIONAL CONTROLS
For a buzzer, a remote
switch…