Nitsuko ST4 User manual

ST4 Single Line Telephone
User Guide
Message Waiting Lamp
(Optional)
Lights when you have messages
waiting (if your phone system
can send them). Also flashes
when your ST4 rings.
Flash
While on a call, press Flash for
outside line or PBX features.
Last Number Redial
Lift handset and press LND
to redial your last call.
Volume Control
Use the three-position
volume control to set the
loudness of ringing.
When placing a call in DP
mode, you can dial * to
change to Tone Dialing.
Dial Mode Switch
[On bottom of phone.]
To place a call:
Lift handset + hear dial tone + dial number
To answer a call:
Lift handset when telephone rings
Soft
Medium
Loud
DP Dial Pulse
Tone Dialing
MF
Wall Mounting Instructions on back.

85403MBG01 June 1995
Issue 1-0 Printed in U.S.A. (183)
Installing the Wall Mount Kit
88403-1
88403-2
Retaining
Clips
Handset
Holder
To install the handset hanger:
1. Use a small flat-blade screwdriver to
push the hanger out of the phone.
2. Invert the hanger and push it back
into the phone.
To wall-mount the phone:
1. Using the two screws provided (or
other suitable fasteners), attach the
wall-mount bracket to the wall.
2. Push the phone onto the
mounting tabs and slide down
until it clicks in place.
To store the handset without
hanging up:
1. Hang the handset on the handset
holder.
To remove the phone from the
wall:
1. Push in the two retaining tabs on
the bottom of the phone.
2. Slide the phone up off of the
wall-mount bracket.

Federal Communications Commission (FCC) Note
1.Your ST4 complies with Part 68 of the FCC rules. The label located on the bottom of
the phone contains the FCC registration number and Ringer Equivalence Number
(REN) for this equipment. This information must be provided to the telephone com-
pany if requested.
2.The ST4 is designed to connect to the telephone line by means of standard 625 type
modular jacks.
3. Your ST4 incorporates FCC compliant telephone cords, plugs and jacks and is
designed to be connected to the telephone network using a compatible modular jack
which is FCC Part 68 compliant.
4.The REN of this equipment is to be used to determine the quantity of devices which
may be connected to a telephone line. Exceeding the maximum allowed REN of the
telephone line may result in telephones not ringing in response to an incoming call.
In most areas, but not all, the sum of the RENs must not exceed 5.0. To determine
the maximum allowed in your specific area, contact your local telephone company.
5.If it is determined that this equipment causes harm to the telephone network, the
telephone company will notify you in advance that temporary discontinuance of the
service is required. But if advance notice is not practical, the telephone company will
notify you as soon as possible. You may file a complaint with the FCC if you believe
it is necessary.
6.The telephone company may make changes in its facilities, equipment, operations or
procedures that could affect the operation of this equipment. If this happens the tele-
phone company will provide advance notice in order for you to make the necessary
modifications to maintain uninterrupted service.
7.If this equipment is not operating properly, you should immediately remove it from
your telephone line, to prevent harm to the network, and contact Nitsuko America (or
an authorized repair facility of Nitsuko America). You should not attempt to make
any repairs on your own. For information, please contact:
Nitsuko America, Telecom Division
4 Forest Parkway
Shelton, CT 06484
Tel: [phone]
8.This equipment cannot be used on coin service provided by the telephone company.
Connection to party line service is subject to state tariffs. Contact the state public
utility commission or corporation commission for information.
9. This equipment utilizes a telephone receiver that is Hearing Aid Compatible.

Industry Science Canada Note
Notice
The Canadian Department of Communications label identifies certified equipment. This
certification means that the equipment meets certain telecommunications network pro-
tective, operational and safety requirements. The Department does not guarantee the
equipment will operate to the user’s satisfaction.
Before installing this equipment, users should ensure that it is permissible to be con-
nected to the facilities of the local telecommunications company. The equipment must
also be installed using an acceptable method of connection. In some cases, the compa-
ny’s inside wiring, associated with a single line individual service, may by extended by
means of a certified connector assembly (telephone extension cord). The customer
should be aware that compliance with the above conditions may not prevent degradation
of service in some situations.
Repairs to certified equipment should be made by an authorized Canadian maintenance
facility designated by the supplier. Any repairs or alterations made by the user to this
equipment, or equipment malfunctions, may give the telecommunications company
cause to request the user to disconnect the equipment.
Users should ensure, for their own protection, that the electrical ground connections of
the power utility, telephone lines and internal metallic water pipe system, if present, are
connected together. This precaution may be particularly important in rural areas.
CAUTION:
Users should not attempt to make such connections themselves,
but should contact the appropriate electric inspection authority,
or electrician, as appropriate.
Load Number
The Load Number (LN) assigned to each terminal device denotes the percentage of the
total load to be connected to a telephone loop, which is used by the device to prevent
overloading. The termination on a loop may consist of any combination of devices sub-
ject only to the requirement that the total of the Load Numbers of all the devices does
not exceed 100.