Noble House Home Furnishings Armless Loveseat User manual

Label Picture Description QTY(pc)
A Seat Base 1
B Backrest 1
C Back Cushion 2
D
Wooden Leg With 1 Plastic
Leg
4
Assembly Instructions
Caution: You must read this before you proceed
Armless Loveseat
Parts List
Noble house Home Furnishings LLC Page 1 OF 8

Label Picture Description QTY
①
Plastic Gasket 2
②Allen Key
1
③Spring Ring
2
④Flat Washer
2
⑤Bolt(M8*70mm) 2
Before
Begining
Assembly:
Hardware List
Assembly Preparation
Noble house Home Furnishings LLC Page 2 OF 8

Step 1
Assembly Steps
This Loveseat has multiple parts and may require about 30 minutes to assemble. To give you an
overview of the Sofa parts, the above picture is to help you put the various parts into perspective.
Please read through the instructions below to familiarise yourself with the parts and steps before
assembly.
Take out the Backrest(B), Seat Base(A) out from the carton, place them on a clean, non-marring
surface.
FRONT FACING
Backrest(B)
Seat Base(A)
Back Cushion (C)
Wooden Leg with 1
Plastic Gasket(D)
Wooden Leg with 1
Plastic Gasket(D)
B
A
Noble house Home Furnishings LLC Page 3 OF 8

Open the small Carton to take out the Plastic Gasket(①),Wooden Legs with 1 Plastic
Gasket(D),Bolts(⑤),Flat Washers(④),Spring Washer(③) and Allen Key(②).
Step 2
Step 3
Step 4
Align the mounting brackets under the the Backrest(B) with those at the top-inside of Seat
Base(A),then slide the Backrest(B) downwards to make sure it locks into place as pictured.
Take out the Back Cushions(C) and small Carton out from the bottom of Seat Base(A).
D
C
C
A
B
B
A
⑤
①
④
③
②
small carton
Noble house Home Furnishings LLC Page 4 OF 8

Step 5
Carefully insert the Bolts(⑤) by placing a Sping Washer(③) and a Flat Washer(④) into the
mounting positions on the hind-top(close to left side) of Seat Base(A), to be tighten by Allen Key(②)
to fix the Backrest(B) and Seat Base(A) together.
A
Noble house Home Furnishings LLC Page 5 OF 8

Step6
Step7
Carefully install the Wooden Legs with 1 Plastic Gasket(D) at the bottom of Seat Base(A).
Note:The use of Gaskets are OPTIONAL and are especially useful to help alleviate slight
wobbleness. Some Legs may need more than one gasket while some legs may not need
anyny.
Put the Back Cushions(C) on the Seat Base(A) againes the Backrest(B) as pictured.
Your Armless Loveseat is ready for use.
This Armless Loveseat can only be used on a flat, level surface.
C
C
D
D
D
D
Noble house Home Furnishings LLC Page 6 OF 8

Connect the Conner, Armless Loveseat, Corner and Ottoman together with U shape Metal
Connector(⑥) one by one, above just one combination for reference, you can do the combination
as you want.
Step 1
Step 2
Combination Reference
Take 2 Bolts(③) by placing a Spring Washer(④) and a Flat Washer(⑤) each by Allen Key(②), then
insert the hole of U Shape Metal Connetor(⑥) and fix it on the both sides under inside the Seat
Base(A) as pictured.
*2
*1
②
CORNER
⑤
④
③
⑥
Noble house Home Furnishings LLC Page 7 OF 8

Noble house Home Furnishings LLC Page 8 OF 8