NRS Healthcare Easylift Home Over-Bed Table User manual

1
USER INSTRUCTIONS
EASYLIFT HOME
OVER-BED / OVER-CHAIR TABL
E
S13880 Easylift Home Over-Bed Table S13892 Easylift Home Over-Bed / Over-Chair Table
S13880: Easylift Home Over-Bed Table
Suitable for most divan and slatted beds, as well as height
adjustable medical beds.
S13892: Easylift Home Over-Bed / Over-Chair Table
Suitable for most divan and slatted beds, as well as
height adjustable medical beds. It is also suitable for use
with most chairs (excluding riser recliner chairs).
2. SAFETY
WARNING: The central column is spring loaded.
Make sure the central column hand-wheel is in
position & fully tightened before assembly/
disassembly of the table.
WARNING: Do not exceed the safe working load of
25 kg (4 st).
ALWAYS make sure that the table is correctly positioned
and adjusted to allow it to be used safely and comfortably.
DO NOT lean or sit on the table.
DO NOT place hot objects directly on the table surface.
Maximum heat resistance 65°C (149°F).
MAKE SURE the area is clear before moving the table.
TAKE CARE when moving the table over rough or uneven
surfaces. Lift the table over large ridges and wide gaps.
ENTRAPMENT HAZARD: Do not use this product within
318 mm of headboard or other similar object.
ENTRAPMENT HAZARD: Always move the table to a
safe location when the user is sleeping.
3. UNPACKING
Remove the packaging and check all parts carefully.
Contact your supplier immediately if parts are missing or
damaged and do not try and assemble.
3.1 Contents:
2
6
5
3
7
8
10
11
9
4
1
1. Table Top Assembly x 1
2. Central Column Assembly & Inner Rod x 1
Note: Do not remove the PVC anti-rattle sleeves
from either end of the inner rod.
3. Central Column Handwheel x 1
4. Base Assembly x 1 (S13880 only)
5. Base Assembly x 1 (S13892 only)
6. Mushroom Feet x 4
7. M8 x 20 mm Socket Head Button Screws x 4
8. M8 x 40 mm Socket Head Button Screws x 4
9. Castors x 4
10. Allen Key x 1
11. Castor Spanner x 1
General Safety Warning
Please make sure that you read and follow these
instructions carefully. Keep these instructions in a
safe place for future reference.
Safe Working Load
4st
25kg
1. INTENDED USE
To provide users with a rm, at surface that is suitable for eating, writing, reading, etc. The single column construction
and adjustable height makes them suitable for use with most types of beds and chairs. This product is NOT suitable
for riser recliner chairs.
S13880 S13892

2
4. ASSEMBLY
Note: We recommend a 2 person assembly.
4.1 Fit the Central Column Handwheel
Insert the hand-wheel and turn clockwise to tighten.
4.2 Assemble the Table Top & Central Column
(S13880 & S13892)
B
B
1. Slide the inner rod (B) into the central column.
Note: Make sure the anged end is facing the correct
way up. The plastic anti-rattle cover is marked ‘UP’.
A
B
2. Guide the anged end of the inner rod (B) into the
height adjustment lever hole in the main frame.
Note: Make sure the label on the central column is facing
inwards before assembly.
3. Secure the column assembly to the table top
assembly using the 4 x M8 x 20 mm socket head screws
and the Allen Key provided.
4. Make sure that all four screws are fully tight before
you continue the assembly.
4.3 Assemble the Base to the Central Column
(S13880 only)
Note: Make sure that the base faces the same direction
as the table top and the castor inserts face upwards (as
shown).
A
B
1. Secure the base assembly to the column assembly
using the 4 x M8 x 40 mm socket head screws and the
Allen Key provided.
2. Make sure that all four screws are fully tight before
you continue the assembly.
4.4 Assemble the Base to the Central Column
(S13892 only)
Note: Make sure that the base faces the same direction
as the table top and the castor inserts face upwards (as
shown).
1. Secure the base assembly to the column assembly
using the 4 x M8 x 40mm socket head screws and the
Allen Key provided.

3
2. Make sure that all four screws are fully tight before
you continue the assembly.
4.5 Fitting the Castors / Feet
4.5.1 Fitting the Castors (S13880 & S13892)
Note: The castor tting method is the same for both
products, S13880 assembly is shown in the gure below.
1. Insert the screw thread into the threaded insert,
hold the castor and turn the nut by hand until the threads
engage.
2. Tighten the castor threads using the 14mm spanner
provided.
3. To remove the castors reverse step 1 & 2.
4.5.2 Fitting the mushroom feet (S13880 & S13892)
The mushroom feet should be tted for use with a low
base divan.
Note: The mushroom feet tting method is the same for
both products, S13880 is shown in the gure below.
Press-t the mushroom feet into the castor insert holes.
5. IN USE
5.1 Locking and Unlocking the Brakes.
The table has 4 independently lockable castors. We
recommend that the castor locks are always fully engaged
when the product is in use or stationary.
Fig 1: Castor Unlocked Fig 2: Castor Locked
1. To lock the castor brake, press down on the castor
tab (Fig 1).
2. To disengage the castor brake, ip up the castor tab
(Fig 2).
5.2 Raising & Lowering the Table
A
B
1. To release the central column, unscrew the locking
handwheel (A) by turning anti-clockwise.

4S13880-UI-4 23-10-2023
2. Pull lever (B) up to release the spring mechanism,
then simultaneously raise or lower the table-top into
position.
3. To lock the central column, screw the locking hand-
wheel (A) clockwise.
6. MAINTENANCE
Regularly check the wheels rotate freely.
Regularly check the brakes function correctly in
accordance with Section 5.1.
Always check the locking handwheel is fully tight before
use.
Make sure the hand-lever is functioning correctly.
7. CLEANING INSTRUCTIONS
Make sure that all dirt and debris is removed from around
the wheels.
Clean regularly using a general purpose, neutral detergent
and warm water.
Please check the suitability of the cleaning products
before use. Do not use abrasive cleaners or cloths as
these could permanently damage the surface and
invalidate any warranty.
DO NOT use solvents to clean the product (if painted)
To disinfect, wipe with a dilute bleach solution, and rinse
thoroughly with fresh water.
Allow product to fully dry prior to use/storage.
8. ACCESSORIES & SPARE PARTS
S20161: Spares Kit
• Replacement Mushroom Feet (set of 4).
• Replacement Castors (set of 4).
For more details please visit our website or call Customer
Services on the details below.
9. PRODUCT DISPOSAL
This product must be thoroughly cleaned/sterilised prior
to disposal.
This product is manufactured from metal, wood &
plastic and can be disposed of through Local Authority
Household Waste and Recycling Centres or through
Local Trade Waste Collectors.
10. PRODUCT GUARANTEE
NRS Healthcare guarantee this product for a period of
24 months, from the date of purchase, against faulty
materials and workmanship.
This guarantee does not cover abuse, interference or
tampering with any part of the products. Issues arising
from fair wear & tear and customer misuse are not
covered.
This guarantee covers domestic use only. If the product is
used in commercial or semi-commercial settings such as
care homes, schools, rental or communal accommodation
etc, the guarantee is valid for one year only. Consumable
parts are also guaranteed for one year only.
Any guarantee issued by NRS Healthcare does not a󰀨ect
your statutory rights.
NRS HEALTHCARE Sherwood House, Cartwright Way, Forest Business Park
Bardon Hill, Coalville, Leicestershire, LE67 1UB, UK.
Tel: Customer Services:[phone] Email: [e-mail]
NRS Healthcare is a leading supplier of community equipment and daily living aids.
Please visit one of our websites to view our full range of products:
www.healthcarepro.co.uk or www.completecareshop.co.uk