NRS Healthcare P42809 User manual

1
USER INSTRUCTIONS
FOLDING EASYFIT BED RAIL
General Safety Warning
Please make sure that you read and follow these
instructions carefully. Keep these instructions in a
safe place for future reference.
1. INTENDED USE
The Folding EasyFit Bed Rail provides stable support to aid adult users (taller than 1.46m) transfer in and out of bed,
moving from a lying to a sitting position as well as assist user repositioning. This product is suitable for all sized divan
and framed beds, and can be fitted to either side of the bed. Supplied with bed rail straps for additional security.
P42809 Folding EasyFit Bed Rail (with straps)
Maximum User Weight
20st
127kg
2. SAFETY
318mm
Min
WARNING: To avoid possible entrapment, you must
always position the product a minimum of 318mm from
the headboard or footboard.
WARNING: To avoid possible entrapment, you must
always position the product a minimum of 318mm
from solid objects/furniture such as bedside drawers or
cabinets.
WARNING: The maximum user weight must not be more
than 127Kg (20st).
YOU MUST carry out a risk assessment to assess the
use and suitability of the bed rail in relation to the users
physical and cognitive ability, as well as the surrounding
environment.
DO NOT install this product to a damaged bed.
MAKE SURE there is no gap between the bed rail and
the mattress.
ALWAYS use the bed securing straps provided when
fitting to a divan bed.
REGULARLY check the straps are tight and the device is
stable and firmly fitted.
DO NOT fit this product to medical or profiling beds.
3. UNPACKING
Remove the packaging and check all parts carefully.
Contact your supplier immediately if parts are missing or
damaged and do not try and assemble.
1
2
3
6
45
Figure 1: EasyFit Bed Rail Assembly
3.1 Contents
Note: The Folding EasyFit Bed Rail is supplied pre-
assembled in the folded position.
1. Bed Rail Handle 4. Plastic Saddle-Washers x 2
2. Bed Rail Base 5. Steel Bolts x 2
3. Plastic Wing-Nuts x 2 6. Bed Rail Straps
4. ASSEMBLY
1. Refer to Figure 1. The bed rail handle (1) can be
rotated in both directions, please make sure it is in
the correct position for your installation.
2. Unscrew the two plastic wing-nuts (3), then remove
the two plastic saddle-washers (4) and the two
bolts (5).
4.1 Right-Hand Side Assembly
Footboard
Headboard 1
3
4
5
2
Figure 2: RHS Assembly

2
1. Refer to Figure 2. Position the bed rail base (2) as
shown.
2. Rotate the bed rail handle (1) 90 degrees.
3. Insert the bolts (5) into the holes, making sure they
locate fully into the hexagonal recess.
4. Replace the two saddle-washers (4) and secure with
the two plastic wing-nuts (3).
5. Make sure the bed rail handle (1) is fully secure
before installing to the bed.
4.2 Left-Hand Side Assembly
Footboard
Headboard
2
1
Figure 3: LHS Assembly
1. Refer to Figure 3. Position the bed rail base (2) as
shown.
2. Rotate the bed rail handle (1) 90 degrees.
3. Refer to Section 4.1. Repeat steps 3 to 5.
5. INSTALLATION
5.1 Fitting to a Divan Bed
WARNING: You must use the straps provided when
fitting to a divan bed. An unsecured bedrail could move
causing risk of entrapment.
5.1.1 Position the Bed Rail
1. Remove the mattress and place the bed rail onto the
base of the bed.
318mm
Min
2. Position the bed rail so the user can reach the
handle from a relaxed lying position without having
to stretch.
WARNING: To avoid possible entrapment, you must
always position the product a minimum of 318mm from
the headboard or footboard.
WARNING: To avoid possible entrapment, you must
always position the product a minimum of 318mm
from solid objects/furniture such as bedside drawers or
cabinets.
5.1.2 Fitting the Straps
With the first strap, tie a secure knot on the hand rail
assembly in the position shown, then repeat for the
opposite site with the second strap.
Note: The strap buckle should hang down the side of the
bed between 50 to 75mm.
5.1.3 Securing the Straps
1. Loop the first strap around the bed rail base in the
position shown.

3
2. Feed the strap over the top of the bed and back
underneath the base.
Note: To fit the strap under the divan base, take the strap
to the end of the divan base, lift up the end of the divan
base and feed the strap underneath the legs / castors.
3. Clip the two strap buckles together.
4. Pull down on the loose end of the strap to tighten.
5. Make sure the bed rail base is tight against the divan
base.
Note: To avoid tripping hazards, make sure you tuck
away any loose strap ends.
6. Repeat for the second strap on the opposite side of
the bed rail.
7. The bed rail should now be fully secured to the divan
base.
5.2 Fitting to a Framed Bed with Fixed Slats
5.2.1 Position the Bed Rail
318mm
Min
1. Remove the mattress and place the bed rail onto the
base of the bed.
2. Position the bed rail so the user can reach the handle
from a relaxed lying position without having to stretch.
WARNING: To avoid possible entrapment, you must
always position the product a minimum of 318mm from
the headboard or footboard.
WARNING: To avoid possible entrapment, you must
always position the product a minimum of 318mm
from solid objects/furniture such as bedside drawers or
cabinets.
5.2.2 Fitting with Straps
Note: If the bed has securely fixed slats, we strongly
recommend securing the bedrail with the straps provided
using the method below:
1. Thread one end of the strap from under the bed up
around the bed slat, then thread around the bed rail
base as shown.
2. Repeat the step using the other end of the strap on
the opposite side of the bed rail base.
5.2.3 Securing the Straps
Underside of the Bed
1. Pull both buckles so they meet in the middle on the
underside of the bed, then clip together.
2. Pull down on the loose end of the strap to tighten.
Note: To avoid tripping hazards, make sure you tuck
away any loose strap ends.
3. Make sure the bed rail is fully secure before replacing
the mattress.

4
NRS HEALTHCARE Sherwood House,
Cartwright Way, Forest Business Park, Bardon
Hill, Coalville, Leicestershire, LE67 1UB, UK.
NRS HEALTHCARE 4C Altona Road, Blaris
Industrial Estate, Lisburn, Co Antrim,
Northern Ireland BT27 5QB
Tel: Customer Services: 0345 121 8111 Email: [email protected]
NRS Healthcare is a leading supplier of community equipment and daily living aids.
Please visit one of our websites to view our full range of products:
www.healthcarepro.co.uk or www.completecareshop.co.uk
P42809-UI-4 03-08-2021
5.3 Fitting to a Framed Bed with Non-Fixed Slats
Note: Straps cannot be used on a bed with non-fixed
slats.
Repeat the steps in section 5.2, but do not use straps.
1. Replace the mattress, making sure there is no gap
between the bed rail and the mattress.
6. CLEANING
6.1 Cleaning the Hand Rail & Base
Please check the suitability of the cleaning products
before use. Do not use solvents, abrasive cleaners or
cloths as these could permanently damage the surface
and invalidate any warranty.
Clean the frame regularly, using a general purpose,
neutral detergent and warm water.
To disinfect, wipe with a dilute bleach solution, and rinse
thoroughly with fresh water.
Allow product to fully dry prior to use/storage.
6.2 Cleaning the Straps
Clean with sponge and warm soapy water, then rinse
thoroughly with fresh water.
Allow product to fully dry before use/storage.
Do not use bleach or solvents.
7. MAINTENANCE
Note: The following checks should be carried out on a
daily basis.
Check the wing-nuts are fully tightened and that there is
no excessive movement.
Check that the bed rail is correctly positioned (minimum
of 318mm from the headboard, footboard or solid objects/
furniture).
Make sure there is no gap between the bed rail and the
mattress.
Inspect the product for signs of wear or damage at regular
intervals.
Any suspected faults or damage must be reported to the
supplier and the product taken out of use immediately.
8. ACCESSORIES & SPARE PARTS
L75930: Bed Rail Strap
P43062: (2 x Plastic Wing-Nuts, 2 x Plastic Saddle-
Washers & 2 Steel Bolts).
For more details please visit our website:
www.nrshealthcare.co.uk or call Customer Services.
9. PRODUCT DISPOSAL
This product should be thoroughly cleaned prior to
disposal.
This product is manufactured from metal and plastic and
can be disposed of through Local Authority Household
Waste and Recycling Centres or through Local Trade
Waste Collectors.
10. PRODUCT GUARANTEE
NRS Healthcare guarantee this product for a period of
12 months, from the date of purchase, against faulty
materials and workmanship.
This guarantee does not cover; fair wear & tear, abuse,
misuse, interference or tampering with any part of the
product.
Any guarantee issued by NRS Healthcare does not affect
your statutory rights.
If you have any problems with our products, please
contact us at the address below.
If you have experienced an injury, contact us but feel
free to contact the Medical and Healthcare products
Regulatory Agency at:
[email protected].uk