NRS Healthcare M48192 User manual

1
USER INSTRUCTIONS
2 IN 1 BED RAIL Mk2
M48192 2 in 1 Bed Rail Mk2
General Safety Warning
Please make sure that you read and follow these
instructions carefully. Keep these instructions in
a safe place for future reference.
Maximum User Weight
25st
160kg
INTENDED USE
The 2 in 1 Bed Rail provides stable support to aid user transfer in and out of bed, moving from a lying to a
sitting position as well as assist user repositioning.
Designed for use with solid base divan beds and framed beds with fixed slats. Suitable for all bed sizes from
single to king-size, it can also be fitted to super king-size beds with additional straps (refer to Accessories
& Spares Parts).
SAFETY
Warning: To avoid possible head entrapment,
position the bed rail at least 318mm (12.5”) away
from both headboard and footboard.
Warning: The maximum user weight must not be
more than 25st (160kg).
To avoid possible user entrapment make sure there
is no gap between the mattress and the bed rail.
Always use the bed securing straps provided when
fitting to a divan bed.
Regularly check the straps are tight and the device
is stable and firmly fitted.
Not suitable for use by children.
Do not fit this product to profiling or sprung base
divan bed types.
We do not recommend fitting this product to framed
beds with non-fixed slats, unless a suitable risk
assessment has been done.
• NRS recommends the EasyFit Plus Bed Rail for
use on a non-fixed slat, sprung based divan or
profiling bed type.
P63991: EasyFit Plus Bed Rail - Standard
P64004: EasyFit Plus Bed Rail - Tall.
UNPACKING
Remove the packaging and check all parts carefully.
Contact your supplier immediately if parts are
missing or damaged and do not try and assemble.
2
4
3
1
Contents:
1. Hand Rail x 1
2. Bed Rail Board x 1
3. Bed Straps x 2
4. E-Clips x 2

2
ASSEMBLY/INSTALLATION
1. Fitting to a Divan Bed
1.1 Remove the Mattress
Remove the mattress, then place the bed rail board
onto the divan base with the hand rail guide facing
down.
1.2 Assemble the Bed Rail
318mm
Min
Slot the hand rail into the hand rail guide.
Note: Make sure the hand rail angles towards the
footboard.
Secure the hand rail with the two e-clips.
Position the bed rail a minimum of 318mm from the
headboard.
Note: The user should be able to reach the handle
from a relaxed lying position without having to
stretch.
1.3 Fitting the Straps
Feed the strap through one of the triangular slots
at the hand rail end, then tie a secure knot before
passing the strap under the bed rail board and up
through the rear triangular slot.
The strap buckle should hang down the side of the
bed between 50 to 75mm.
1.4 Securing the Straps
Loop the strap around the end of the bed board and
back through the slot. The strap should be tight under
the bed-rail board and the bed-rail board should not
slide on the strap.

3
Feed the strap over the top of the bed and back
underneath the base.
Note: To fit the strap under the divan base, take the
strap to the end of the divan base, lift up the end of
the divan base and feed the strap underneath the
legs / castors.
Clip the two strap buckles together.
Pull down on the loose end of the strap to tighten.
Make sure the bed rail base is tight against the divan
base.
Note: To avoid tripping hazards, make sure you tuck
away any loose strap ends.
Repeat for the second strap on the opposite side of
the bed rail board.
The bed rail should now be fully secured to the divan
base.
Make sure the bed rail is fully secure before replacing
the mattress.
2. Fitting to a Framed Bed with Fixed Slats
2.1 Assemble the Bed Rail
318mm
Min
Remove the mattress and place the bed rail board
inside the wooden bed frame with the hand rail guide
facing up.
Slot the hand rail into the hand rail guide.
Note: Make sure the hand rail angles towards the
footboard.
Secure the hand rail with the two e-clips.
Position the bed rail a minimum of 318mm from the
headboard.
Note: The user should be able to reach the handle
from a relaxed lying position without having to
stretch.
2.2 Fitting the Straps:
Thread one end of the strap from under the bed up
around the bed slat, through the triangular slot on
side of the bed rail board, then back under the bed
past the slat.
Repeat the step using the other end of the strap
through the triangular slot on the opposite side of
the bed rail board.
2.3 Securing the Straps
Underside of the Bed

4
NRS HEALTHCARE Sherwood House, Cartwright Way, Forest Business Park, Bardon Hill, Coalville,
Leicestershire, LE67 1UB, UK.
Tel. Customer Services: 0345 121 8111
Email: [email protected]
NRS Healthcare is a leading supplier of community equipment and daily living aids, to
view our full range, visit our website:
www.nrshealthcare.co.uk
M48192-UI-11
Pull both buckles so they meet in the middle on the
underside of the bed, then clip together. Pull the
loose end of the strap to tighten.
Note: To avoid tripping hazards, make sure you tuck
away any loose strap ends.
Repeat the process for the second strap at the
opposite end of the bed rail board.
Make sure the bed rail is fully secure before replacing
the mattress.
IN USE
Changing the Bedding
The hand rail can be removed to make changing the
bedding easier.
To remove the hand rail, reverse the assembly
process (refer to Section 1.2 or 2.1).
CLEANING
1. Cleaning the Hand Rail & Base
Please check the suitability of the cleaning products
before use. Do not use abrasive cleaners or cloths
as these could permanently damage the surface and
invalidate any warranty.
Clean regularly using a general purpose, neutral
detergent and warm water.
To disinfect, wipe with a dilute bleach solution, and
rinse thoroughly with fresh water. Do not use on the
straps.
Allow product to fully dry prior to use/storage.
2. Cleaning the Straps
Clean with sponge and warm soapy water, then rinse
thoroughly with fresh water.
Allow product to fully dry before use/storage.
Do not use bleach or solvents.
Do not steam clean, tumble dry or dry clean.
MAINTENANCE
Check regularly for signs of wear or damage.
Any suspected faults, excessive wear or damage
must be reported to the supplier and the product
taken out of use immediately.
Check all fixing straps are tight and secure.
Check the bed rail base is correctly positioned.
Make sure there is no gap between the hand rail and
the mattress.
Check both E-clips are correctly fitted and secure.
ACCESSORIES & SPARE PARTS
L75930 - 2 in 1 Bed Rail Strap
For more details please visit our website:
www.nrshealthcare.co.uk or call Customer Services.
PRODUCT DISPOSAL
This product should be thoroughly cleaned prior to
disposal.
This product is manufactured from metal and plastic
and can be disposed of through Local Authority
Household Waste and Recycling Centres or through
Local Trade Waste Collectors.
PRODUCT GUARANTEE
NRS Healthcare guarantee this product for a period
of 12 months, from the date of purchase, against
faulty materials and workmanship.
This guarantee does not cover; abuse, misuse,
interference or tampering with any part of the product.
Any guarantee issued by NRS Healthcare does not
affect your statutory rights.