NRS Healthcare M99266 User manual

USER INSTRUCTIONS
M99266 NRS 4 WHEEL ROLLATOR - BLUE
M99278 NRS 4 WHEEL ROLLATOR
-
RED
Intended Use
The NRS 4 Wheel Rollator is designed to provide
support and assistance to those unable to, or who
lack the confidence to, walk without some level of
support. This rollator is intended for indoor and
outdoor use.
Safety Precautions - Do’s and Don’ts
·Do not exceed the maximum user weight limit of
136Kg (21st)
·Do not use the rollator on stairs or an escalator.
·Do not attempt to push the rollator while
someone is sitting in the seat.
·Do not use the seat to transport people or
objects.
·Do not use the seat without the backrest in
place.
·Do not sit on the seat when the rollator is on an
incline.
·Only use the rollator as a walking support.
·Only use the specified accessories and spare
parts for this rollator
·Loads should only be transported using the
basket. Do not hang heavy items from the
handles as this may affect the stability of the
Rollator.
Safety Precautions - Pre Use Checks
·Ensure Rollator is locked open before use.
·Check the brakes before use.
·Make sure that all parts are secure and that
moving parts are in good working order.
Safety Precautions - During use
·Do not self propel the rollator while seated.
Serious injury to the user and/or damage to the
rollator frame or wheels may result from
improper use.
General Safety Warning
Please ensure these instructions are fully read
and implemented. Failure to do so may result
in injury to the user. Retain in a safe place for
future reference.
Maximum User Weight:
CONTENTS LIST
Item
Description
Qty.
1 Rollator assembly 1
2
3
4
5
Storage Bag
Backrest
Hand wheels with bolts/plastic
washers
User instructions
1
1
2
1
Unpacking
·Check all parts carefully before assembling the
product.
·Do not assemble if any of the parts are
damaged.
·Do not assemble if any of the parts in the
Contents list are missing.
·When unpacking make sure the handles and
brake cables are not twisted as this can affect
the operation of the brakes, when assembled.
·
Do not use the rollator to walk backwards.
·Caution must be taken when negotiating curbs
and other obstacles, or when using on sloping,
uneven or slippery surfaces. Failure to do so
may result in a serious risk of a fall or injury.
·Do not perform any adjustments to the rollator
while it is in use.
·Exercise caution when there is a heavy load in
the bag (max. load 5Kg)
·All wheels must be in contact with the floor at all
times.
·Brakes must be in the locked position before
using the seat.
·When using the rollator in a stationary position,
the brakes must be locked.
Page 1

Assembly and Height Adjustment
NOTE: Before assembly consult a suitably
qualified healthcare professional regarding the
correct height adjustment for maximum support;
and correct brake activation.
1. To assemble, open the rollator frame, push
down on the frame and seat until all four
wheels are extended, the seat is flat and the
cross members are in line, as shown in
diagram 1. Make sure that all four wheels
make contact with the floor and the rollator is
stable in the open position.
2. Position the backrest bar so that the padded
portion faces the front of the rollator. Insert into
the brackets until the push buttons on the bar
lock into place.
3. Insert the Handlebars into the framing tubes
and set to the correct height as follows;
·Stand upright behind the rollator with your
shoulders relaxed and your arms by your side,
looking straight ahead.
·In this position, the handgrips of the rollator
(see diagram 1) should be adjusted to a height
level with your wrists.
·This will position your arms at an approximate
20º to 30º bend when using the rollator.
·Check that the holes in the handle bars and
the frame are aligned.
·Place the supplied bolt through the aligned
holes in the handlebar and frame. The holes in
the frame are hexagonal in shape to
accommodate the head of the bolt.
·Place the washer over the bolt and then apply
the hand nut. Hand-tighten firmly, but do not
over tighten
4. Check the brakes thoroughly before use.
NOTE: The Rollator Brakes are factory set,
and if assembled correctly do not need
adjusting prior to use. To check; Apply and
release the parking brake on each side 10
times. (Push brake lever down to lock, lift to
release) The brake should grip the wheel and
prevent any movement when applied, when
released, the gap between the brake moulding
and the wheel should be between 1 to 3 mm. If
either of the above conditions is not correct
adjust the brakes as detailed in the
maintenance section, and re-check.
5. Check to make sure all other nuts, bolts and
screws are tightly fastened.
6. Check all wheels are in good working order
and roll freely.
Padded
Backrest
Diagram: 1
Padded
Seat
Adjustable
Handlebar
Handgrips
Cross
Member
Brake
Adjusters
Page 2

Operating Instructions
Opening the Rollator
Open the rollator frame by pushing down on the
handlebars until all four wheels are extended out,
the seat is flat and the cross members are in line,
as shown in diagram 1. Make sure that all four
wheels make contact with the floor and the rollator
is stable in the open position.
Folding the Rollator
Lift the seat and pull up on the strap until the
rollator closes.
For more compact storage, remove the backrest.
Walking
This unit is to be used as a mobility aid, creating a
natural gait as the user walks securely with their
primary weight distribution between the
handlebars and with the unit in front of the user.
Sitting
When using the rollator as a seat, ensure the
safety precautions detailed on page one are
adhered to, in particular;
·Ensure the parking brakes are in the locked
position.
·Do not use as a seat without the backrest
being fitted
·Do not use as a seat on sloping or uneven
ground
·Do not exceed the maximum user weight
·Do not use the rollator as a wheelchair
Checking and Operating the Brakes
·Before using the rollator always check the
brakes are working correctly.
·Check the normal brake function by pulling up
the brake handles as shown in diagram 3a, the
rollator should be held firm with no movement.
·To apply the parking brakes, push down the
handles until they lock down. A distinct click
indicates that the brake is in the correct
position, the rollator should be held firm with
no movement. (See Diagram 3b) It is
important that both brakes are used for
parking. Lift up the handles to release the
parking brakes.
Brake Operation
·To slow down, pull up both of the loop
handles. (See Diagram 3a)
·To apply the parking brakes, push down both
handles until they lock down. A distinct click
indicates that the brakes are in the correct
position. (See Diagram 3b) It is important that
both brakes are put in the parking position
when they are used.
·Lift up both handles to release the parking
brakes.
·If you apply the parking brakes, or pull up the
brakes to stop whilst moving, and the rear
wheels on the rollator still move, stop use
immediately. Do not use again until the brakes
have been checked and correctly adjusted.
Refer to the maintenance section.
Diagram: 3a Diagram: 3b
Cleaning Instructions
·Clean regularly, wipe down with a soft, non
abrasive cloth.
·Ensure there is no build up of dirt or debris
around the axle, brakes and wheels.
Maintenance
·Regularly check for wear and tear and that all
screws and knobs are securely fastened.
·Check brakes are working satisfactorily by
both walking and squeezing the brakes and by
braking to a stop.
·Check the parking brakes by pushing the
handles into the locked position, and then
trying to push the rollator.
·If the brakes do not completely lock the
wheels the brakes need to be adjusted.
Page 3

UI/M99266/M99278/04/14/Iss3
These products are included in our range of
over 3000 daily living aids available from
NRS Healthcare.
To view the full range visit;
www.nrs-uk.co.uk
Or request a catalogue from the number below.
NRS Healthcare
Sherwood House, Cartwright Way
Forest Business Park, Bardon Hill
Coalville, Leicestershire. LE67 1UB UK
Tel: [phone]
Fax: [phone]
Email: [e-mail]
www.nrs-uk.co.uk
Maintenance continued;
Brake Adjustment
(see Diagram 4)
·There are two brake adjusters on each side of
the Rollator, one is positioned in front of the
brake handle and the second above the rear
wheel (See diagram 1)
·Brake Adjustment: To tighten the brake,
loosen the lock nut, turn the adjuster
anticlockwise, then retighten the lock nut.
(See Diagram 4)
·For correct adjustment the brake mechanism
should not touch the wheel, but the gap
should be no greater than 3mm.
·Caution: After making any adjustments to the
brakes, you must test them before the rollator
is used.
·If adjustment does not tighten the brakes, do
not use the rollator. Contact your dealer or
NRS Customer services, details below.
If you use this product….you may also find
useful:
Aids for getting into and out of the car
Handybar
M14674
Car Caddie
M15393
Swivel Seat Deluxe L33996
Locknut
Page 4
Diagram: 4 –Handle brake adjustment
Turn Adjuster
Anti-clockwise
to tighten
brake