NUVE NF 200 User manual

0
NÜVE SANAYİ MALZEMELERİ İMALAT VE TİCARET A.Ş.
NF 200
BENCH - TOP CENTRIFUGE
USER’S MANUAL
Z14. K25 249 Rev. No: 08 Rev.Date: 01/2016

1
MANUFACTURER:
NÜVE SANAYİ MALZEMELERİ
İMALAT VE TİCARET A.Ş.
Saracalar Mah. Saracalar Kümeevleri No: 4/2 Akyurt 06750 Ankara-TURKEY
TEL: +(90) 312 399 28 30 (pbx)
FAX: +(90) 312 399 21 97
E-mail:[e-mail]
WARRANTY CERTIFICATE
1. Nüve warrants that the equipment delivered is free from defects during material and
workmanship. This warranty is provided for a period of two years. The warranty period
begins from the delivery date.
2. Warranty does not apply to parts normally consumed during operation or general
maintenance or any adjustments described in the operating instructions provided with the
equipment.
3. Nüve does not accept any liability in the case where the goods are not used in accordance
with their proper intent.
4. The warranty may not be claimed for damages occurred during the shipment, for damages
resulting from improper handling or use, the defects in maintenance, negligence, bad
functioning of auxiliary equipment, in the case of force majeure or accident and incorrect
power supply.
5. In the event of failure, Nüve shall be under no liability for any injury, or any loss or damage
as the result of the failure other than the guarantee conditions.
BEFORE OPERATING THE INSTRUMENT THIS MANUAL SHOULD BE READ
CAREFULLY.
THE VALIDITY OF THE GUARANTEE IS SUBJECT TO THE OBSERVATION OF THE
INSTRUCTIONS AND PRECAUTIONS DESCRIBED IN THIS MANUAL.
INFORMATION CONTAINED IN THIS DOCUMENT IS THE PROPERTY OF NÜVE. IT MAY
NOT BE DUPLICATED OR DISTRIBUTED WITHOUT PERMISSION.

2
Dear Nüve User,
We would like to take this opportunity to thank you for preferring this Nüve product. Please read
the operating instructions carefully and keep them handy for future reference.
Please detain the packing material until you see that the unit is in good condition and it is operating
properly. If an external or internal damage is observed, contact the transportation company
immediately and report the damage. According to ICC regulations, this responsibility belongs to the
customer.
While you are operating the instrument please;
•obey all the warning labels,
•do not remove the warning labels,
•do not operate damaged instrument,
•do not operate the instrument with a damaged cable,
•do not move the instrument during operation.
In case of a problem contact your Nüve agent for an authorized service or maintenance.
The validity of the guarantee is subject to compliance with the instructions and precautions
described in this manual.
Nüve reserves the right to improve or change the design of its products without any obligation to
modify previously manufactured products.
Information contained in this document is the property of Nüve. It may not be duplicated or
distributed without its permission.
PLEASE REGISTER ONLINE TO VALIDATE WARRANTY:
To register your warranty online, please visit our web page www.nuve.com.tr and fill in WARRANTY
REGISTRATION FORM.

3
TABLE OF CONTENTS
SECTION 1 .................................................................................................................................... 4
INTRODUCTION............................................................................................................................ 4
1.1 USE AND FUNCTION .........................................................................................................................4
SECTION 2 .................................................................................................................................... 5
TECHNICAL SPECIFICATIONS.................................................................................................... 5
2.1 TECHNICAL SPECIFICATIONS TABLE.............................................................................................5
2.2 OPTIONAL ACCESSORIES................................................................................................................5
2.3 GENERAL PRESENTATION...............................................................................................................6
2.4 PRECAUTIONS AND USAGE LIMITATIONS.....................................................................................6
SECTION 3 .................................................................................................................................... 7
SYMBOLS...................................................................................................................................... 7
SECTION 4 .................................................................................................................................... 8
INSTALLATION PROSEDURE..................................................................................................... 8
4.1 LIFTING AND TRANSPORT ...............................................................................................................8
4.2 UNPACKING .......................................................................................................................................8
4.3 POSITIONING.....................................................................................................................................8
4.4 ENVIRONMENTAL CONDITIONS......................................................................................................8
4.5 MAINS SUPPLY ..................................................................................................................................8
SECTION 5 .................................................................................................................................... 9
WORKING PRINCIPLES ............................................................................................................... 9
5.1 CONTROL PANELİ..............................................................................................................................9
SECTION 6 .................................................................................................................................. 10
OPERATING PRINCIPLES.......................................................................................................... 10
6.1 LOADING...........................................................................................................................................10
6.2 PROGRAMMING...............................................................................................................................11
6.3 MANUAL LID OPENING....................................................................................................................11
SECTION 7 ................................................................................................................................. 12
PERIODIC MAINTENANCE, CLEANING AND STERILIZATION ................................................ 12
7.1 PERIODIC MAINTENANCE..............................................................................................................12
7.2 CLEANING ........................................................................................................................................12
7.3 STERILIZATION................................................................................................................................13
SECTION 8 .................................................................................................................................. 13
DISPOSAL MANAGEMENT CONCEPT...................................................................................... 13
SECTION 9 .................................................................................................................................. 14
TROUBLESHOOTING................................................................................................................. 14
SECTION 10 ................................................................................................................................ 15
ELECTRICAL CIRCUIT DIAGRAM.............................................................................................. 15
10.1 NF 200 ELECTRICAL CIRCUIT DIAGRAM...................................HATA!YER İŞARETİ TANIMLANMAMIŞ.
SECTION 11 ............................................................................................................................... 16
WARNING LABEL....................................................................................................................... 16

4
SECTION 1
INTRODUCTION
1.1 USE AND FUNCTION
NF 200 Bench Top Centrifuge is especially designed for the separation of blood samples,
sedimentation of urine particles and for the separation of substance or substance mixtures in
laboratories.
By means of the programmable microprocessor control system, speed, RCF value and time could
be programmed and the ‘pulse’ function allows the operator to run short spins.
NF 200 ensures safe operation by means of the locking system which does not allow the centrifuge
to operate if the lid is open the lid cannot be opened while the rotor is spinning.
There are audible and visible alarms to inform the operator when the lid is open, when the program
ends and when any error condition occurs. In case of a power failure, the lid could be opened
manually by using a manual lid opening tool. There is also an observation hole on the lid to check
the speed of the centrifuge by a tachometer.
NF 200 is delivered with 12x15 ml angle rotor made of polypropylene.
The NF 200 Bench Top Centrifuge is manufactured according to the following standards:
EN 61010-1, EN 61010-2-020, EN 61000-6-3, EN 50419.
This device is in compliance with WEEE Regulation.