Nuvoton NuMaker-emWin-N9H30 User manual

NuMaker-emWin-N9H30
Apr. 22, 2021 Page 1of 36 Rev 2.12
NUMAKER-EMWIN-N9H30 USER MANUAL
ARM®ARM926EL-S Based
32-bit Microprocessor
NuMaker-emWin-N9H30
User Manual
The information described in this document is the exclusive intellectual property of
Nuvoton Technology Corporation and shall not be reproduced without permission from Nuvoton.
Nuvoton is providing this document only for reference purposes of NuMicro microcontroller based system
design. Nuvoton assumes no responsibility for errors or omissions.
All data and specifications are subject to change without notice.
For additional information or questions, please contact: Nuvoton Technology Corporation.
www.nuvoton.com

NuMaker-emWin-N9H30
Apr. 22, 2021 Page 2of 36 Rev 2.12
NUMAKER-EMWIN-N9H30 USER MANUAL
Table of Contents
1Overview.............................................................................................3
2Introduction to NuMaker-emWin-N9H30 Board ...............................................5
2.1 NuMaker-emWin-N9H30 Board Features ......................................................... 5
2.2 NuMaker-emWin-N9H30 Board －Front View.................................................... 6
2.3 NuMaker-emWin-N9H30 Board －Rear View...................................................11
2.4 NuMaker-TFT-LCD7 －Front View................................................................17
2.5 NuMaker-TFT-LCD7 －Rear View ................................................................18
2.6 NuMaker-emWin-N9H30 and NuMaker-TFT-LCD7 PCB Placement.........................19
3NuMaker-emWin-N9H30 and numAKER-tft-lcd7 Schematics ............................ 23
3.1 NuMaker-emWin-N9H30 －GPIO List Schematic ..............................................23
3.2 NuMaker-emWin-N9H30 －System Block Schematic .........................................23
3.3 NuMaker-emWin-N9H30 －Power Schematic ..................................................24
3.4 NuMaker-emWin-N9H30 －N9H30F61IEC Schematic ........................................25
3.5 NuMaker-emWin-N9H30 －Setting, ICE, RS-232_0, Key Schematic.......................26
3.6 NuMaker-emWin-N9H30 －Memory Schematic ................................................27
3.7 NuMaker-emWin-N9H30 －I2S, I2C_0, RS-485_6 Schematic ...............................28
3.8 NuMaker-emWin-N9H30 －RS-232_2 Schematic..............................................29
3.9 NuMaker-emWin-N9H30 －LCD Schematic.....................................................30
3.10 NuMaker-emWin-N9H30 －CMOS Sensor, I2C_1. CAN_0 Schematic.....................31
3.11 NuMaker-emWin-N9H30 －RMII_0_PF Schematic ............................................32
3.12 NuMaker-emWin-N9H30 －RMII_1_PE Schematic ............................................33
3.13 NuMaker-emWin-N9H30 －USB Schematic.....................................................34
3.14 NuMaker-TFT-LCD7 －LCD Schematic..........................................................35
4Revision History .................................................................................. 36

NuMaker-emWin-N9H30
Apr. 22, 2021 Page 3of 36 Rev 2.12
NUMAKER-EMWIN-N9H30 USER MANUAL
1 OVERVIEW
The NuMaker-emWin-N9H30 development board is a specific development tool based on
N9H30F61IEC IC to provide customers with a low cost and ease of development. It can be easily
customized for customers to provide their own HMI (Human Machine Interface) device server
products.
Figure 1-1 NuMaker-emWin-N9H30 Development Board (Front View)

NuMaker-emWin-N9H30
Apr. 22, 2021 Page 4of 36 Rev 2.12
NUMAKER-EMWIN-N9H30 USER MANUAL
Figure 1-2 NuMaker-emWin-N9H30 Development Board (Rear View)

NuMaker-emWin-N9H30
Apr. 22, 2021 Page 5of 36 Rev 2.12
NUMAKER-EMWIN-N9H30 USER MANUAL
2 INTRODUCTION TO NUMAKER-EMWIN-N9H30 BOARD
The NuMaker-emWin-N9H30 solution uses an outstanding CPU core ARM926EJ-S,
N9H30F61IEC IC which runs up to 300 MHz and features the embedded 64MB DDR memory,
with 16 KB I-cache, 16 KB D-cache and MMU, 56 KB embedded SRAM and 16 KB IBR (Internal
Boot ROM) for booting from SPI Flash or booting from NAND Flash.
The NuMaker-emWin-N9H30 solution integrates touchscreen display, voice input/output, rich
serial port service and I/O interface, providing multiple external storage methods. It contains two
kinds of board, including the NuMaker-emWin-N9H30 board and NuMaker-TFT-LCD7 board.
2.1 NuMaker-emWin-N9H30 Board Features
N9H30F61IEC IC: LQFP216 pin MCP package with DDR (64 MB).
SPI Flash use W25Q256JVEQ (32 MB) booting with quad mode or storage memory.
NAND Flash use W29N01HVSINA (128 MB) booting or storage memory.
Provide one Micro-SD/TF card slot served either as a SD memory card for data storage or
SDIO (Wi-Fi) device.
Provides 2 sets of COM ports.
One DB9 RS-232 port with UART_0 used 75C3232E transceiver IC can be served for
function debug and system development.
One DB9 RS-232 port with UART_2 used 75C3232E transceiver IC for user
application
22 GPIO expansion ports, including 7 sets UART function
JTAG interface provided for software development.
Microphone input and Earphone/Speaker output with 24-bit stereo audio codec
(NAU88C22) for I2S interfaces.
6 sets of user-configurable push button keys.
3 sets of LED for status indication.
Provided SN65HVD230 transceiver IC for CAN bus communication.
Provided MAX3485 transceiver IC for RS-485 device connection.
Provided one buzzer device for program application.
2 sets of RJ45 port with Ethernet 10/100Mbps MAC used IP101GR PHY IC
USB_0 that can be used as Device/HOST and USB_1 that can be used as HOST
supports pen drives, keyboards, mouse and printers.
7”resolution 800x480 4W resistive touch panel for 24bits RGB888 interface.
Provides over-voltage and over current protection used APL3211A IC
Retain RTC battery socket is for CR2032 type and ADC0 detect battery voltage.
System powered could be supplied by DC-5V adaptor or USB VBUS..

NuMaker-emWin-N9H30
Apr. 22, 2021 Page 6of 36 Rev 2.12
NUMAKER-EMWIN-N9H30 USER MANUAL
2.2 NuMaker-emWin-N9H30 Board －Front View
Figure 2-1 shows the main components and connectors from the front view of NuMaker-emWin-
N9H30 board.
NuMaker-emWin-N9H30 board and LCD panel board combination connector (CON8).
Support 4W/5W resistive touch panel for 24bits RGB888 interface
Connector
GPIO pin of N9H30
Function
CON8.1
-
Power 3.3V
CON8.2
-
Power 3.3V
CON8.3
GPD7
LCD_CS
CON8.4
GPH3
LCD_BLEN
CON8.5
GPG9
LCD_DEN
CON8.6
GPG8
LCD_VSYNC
CON8.7
GPG7
LCD_HSYNC
CON8.8
GPG6
LCD_CLK
CON8.9
GPD15
LCD_D23(R7)
CON8.10
GPD14
LCD_D22(R6)
CON8.11
GPD13
LCD_D21(R5)
CON8.12
GPD12
LCD_D20(R4)
CON8.13
GPD11
LCD_D19(R3)
CON8.14
GPD10
LCD_D18(R2)
CON8.15
GPD9
LCD_D17(R1)
CON8.16
GPD8
LCD_D16(R0)
CON8.17
GPA15
LCD_D15(G7)
CON8.18
GPA14
LCD_D14(G6)
CON8.19
GPA13
LCD_D13(G5)
CON8.20
GPA12
LCD_D12(G4)
CON8.21
GPA11
LCD_D11(G3)
CON8.22
GPA10
LCD_D10(G2)
CON8.23
GPA9
LCD_D9(G1)
CON8.24
GPA8
LCD_D8(G0)
CON8.25
GPA7
LCD_D7(B7)
CON8.26
GPA6
LCD_D6(B6)

NuMaker-emWin-N9H30
Apr. 22, 2021 Page 7of 36 Rev 2.12
NUMAKER-EMWIN-N9H30 USER MANUAL
CON8.27
GPA5
LCD_D5(B5)
CON8.28
GPA4
LCD_D4(B4)
CON8.29
GPA3
LCD_D3(B3)
CON8.30
GPA2
LCD_D2(B2)
CON8.31
GPA1
LCD_D1(B1)
CON8.32
GPA0
LCD_D0(B0)
CON8.33
-
-
CON8.34
-
-
CON8.35
-
-
CON8.36
-
-
CON8.37
GPB2
LCD_PWM
CON8.38
GPG4
LCD_RST
CON8.39
-
VSS
CON8.40
-
VSS
CON8.41
ADC7
XP
CON8.42
ADC3
Vsen
CON8.43
ADC6
XM
CON8.44
ADC4
YM
CON8.45
-
-
CON8.46
ADC5
YP
CON8.47
-
VSS
CON8.48
-
VSS
CON8.49
GPG0
I2C0_C
CON8.50
GPG1
I2C0_D
CON8.51
GPG5
TOUCH_INT
CON8.52
-
-
CON8.53
-
-
CON8.54
-
-
CON8.55
-
-
CON8.56
-
-
CON8.57
-
-

NuMaker-emWin-N9H30
Apr. 22, 2021 Page 8of 36 Rev 2.12
NUMAKER-EMWIN-N9H30 USER MANUAL
CON8.58
-
-
CON8.59
-
VSS
CON8.60
-
VSS
CON8.61
-
-
CON8.62
-
-
CON8.63
-
Power 5V
CON8.64
-
Power 5V
Power supply switch (SW_POWER1): System will be power on if the SW_POWER1 button
is pressed.
3sets indication LEDs:
LED
Color
Descriptions
LED1
Red
The system power will
be terminated and LED1
lighting when the input
voltage is over 5.7V or
the current is over 2A.
LED2
Green
Power normal state.
LED3
Green
Controlled by GPH2 pin
6sets user SWs, Key Matrix for user definition.
Key
GPIO pin of N9H30
Function
K1
GPF10
Row0
GPB4
Col0
K2
GPF10
Row0
GPB5
Col1
K3
GPE15
Row1
GPB4
Col0
K4
GPE15
Row1
GPB5
Col1
K5
GPE14
Row2
GPB4
Col0
K6
GPE14
Row2
GPB5
Col1

NuMaker-emWin-N9H30
Apr. 22, 2021 Page 9of 36 Rev 2.12
NUMAKER-EMWIN-N9H30 USER MANUAL
NAND Flash (128 MB) with Winbond W29N01HVS1NA (U9).
Microphone (M1): Through the nuvoTon NAU88C22 IC sound input.
Audio CODEC IC (U10): nuvoTon NAU88C22 IC connects to N9H30 using I2S interface.
SW6/SW7/SW8: 1-2 short for RS-485_6 function and connected to 2P terminal (CON5
and J5).
SW6/SW7/SW8: 2-3 short for I2S function and connected to NAU88C22 (U10).
CMOS Sensor connector (CON10, SW9~10)
Connector
GPIO pin of N9H30
Function
CON10.1
-
VSS
CON10.2
-
VSS
CON10.3
-
Power 3.3V
CON10.4
-
Power 3.3V
CON10.5
-
-
CON10.6
-
-
CON10.7
GPI4
S_PCLK
CON10.8
GPI3
S_CLK
CON10.9
GPI8
S_D0
CON10.10
GPI9
S_D1
CON10.11
GPI10
S_D2
CON10.12
GPI11
S_D3
CON10.13
GPI12
S_D4
CON10.14
GPI13
S_D5
CON10.15
GPI14
S_D6
CON10.16
GPI15
S_D7
CON10.17
GPI6
S_VSYNC
CON10.18
GPI5
S_HSYNC
CON10.19
GPI0
S_PWDN
CON10.20
GPI7
S_nRST
CON10.21
GPG2
I2C1_C
CON10.22
GPG3
I2C1_D
CON10.23
-
VSS
CON10.24
-
VSS

NuMaker-emWin-N9H30
Apr. 22, 2021 Page 10 of 36 Rev 2.12
NUMAKER-EMWIN-N9H30 USER MANUAL
SW9~10: 1-2 short for CAN_0 function and connected to 2P terminal (CON11).
SW9~10: 2-3 short for CMOS sensor function and connected to CMOS sensor
connector (CON10).
Combination Connector
(CON8)
CMOS Sensor Connector
(CON10, SW9~10)
RS-485 Transceiver
(U11)
CAN Transceiver
(U13)
RS-232 Transceiver
(U6, U12)
NAND Flash
(U9)
Audio CODEC IC
(U10, SW6~8)
Microphone
(M1)
Power Supply Switch
(SW_POWER1)
3set Indication LEDs
(LED1~3)
6set User SWs
(K1~6)
Figure 2-1 NuMaker-emWin-N9H30 Board (Front View)

NuMaker-emWin-N9H30
Apr. 22, 2021 Page 11 of 36 Rev 2.12
NUMAKER-EMWIN-N9H30 USER MANUAL
2.3 NuMaker-emWin-N9H30 Board －Rear View
Figure 2-2 shows the main components and connectors from the rear view of NuMaker-emWin-
N9H30 board.
+5V In (CON1): Power adaptor 5V input.
JTAG ICE interface (J2).
Connector
GPIO pin of N9H30
Function
J2.1
-
Power 3.3V
J2.2
GPJ4
nTRST
J2.3
GPJ2
TDI
J2.4
GPJ1
TMS
J2.5
GPJ0
TCK
J2.6
-
VSS
J2.7
GPJ3
TD0
J2.8
-
RESET
SPI Flash (32 MB) with Winbond W25Q256JVEQ (U7), only one (U7 or U8) SPI Flash can
be used.
System Reset (SW5): system will be reset if the SW5 button is pressed.
Buzzer (BZ1): Control by GPB3 pin of N9H30
Speaker output (J4): Through the NAU88C22 chip sound output.
Earphone output (CON4): Through the NAU88C22 chip sound output.
Expand port for user use (CON7):
Connector
GPIO pin of N9H30
Function
CON7.1
-
Power 3.3V
CON7.2
-
Power 3.3V
CON7.3
GPE12
UART3_TXD
CON7.4
GPH4
UART1_TXD
CON7.5
GPE13
UART3_RXD
CON7.6
GPH5
UART1_RXD
CON7.7
GPB0
UART5_TXD
CON7.8
GPH6
UART1_RTS
CON7.9
GPB1
UART5_RXD
CON7.10
GPH7
UART1_CTS

NuMaker-emWin-N9H30
Apr. 22, 2021 Page 12 of 36 Rev 2.12
NUMAKER-EMWIN-N9H30 USER MANUAL
CON7.11
GPI1
UART7_TXD
CON7.12
GPH8
UART4_TXD
CON7.13
GPI2
UART7_RXD
CON7.14
GPH9
UART4_RXD
CON7.15
-
-
CON7.16
GPH10
UART4_RTS
CON7.17
-
-
CON7.18
GPH11
UART4_CTS
CON7.19
-
VSS
CON7.20
-
VSS
CON7.21
GPB12
UART10_TXD
CON7.22
GPH12
UART8_TXD
CON7.23
GPB13
UART10_RXD
CON7.24
GPH13
UART8_RXD
CON7.25
GPB14
UART10_RTS
CON7.26
GPH14
UART8_RTS
CON7.27
GPB15
UART10_CTS
CON7.28
GPH15
UART8_CTS
CON7.29
-
Power 5V
CON7.30
-
Power 5V
UART0 selection (CON2, J3):
Connector
GPIO pin of N9H30
Function
J3.1
GPE1
UART0_RXD
J4.2
GPE0
UART0_TXD
RS-232_0 function and connected to DB9 female (CON2) for debug message output.
GPE0/GPE1 connected to 2P terminal (J3).
UART2 selection (CON6, J6):
Connector
GPIO pin of N9H30
Function
J6.1
GPF11
UART2_TXD
J6.2
GPF12
UART2_RXD
J6.3
GPF13
UART2_RTS

NuMaker-emWin-N9H30
Apr. 22, 2021 Page 13 of 36 Rev 2.12
NUMAKER-EMWIN-N9H30 USER MANUAL
J6.4
GPF14
UART2_CTS
RS-232_2 function and connected to DB9 female (CON6) for debug message output.
GPF11~14 connected to 4P terminal (J6).
RS-485_6 selection (CON5, J5, SW6~8):
GPIO pin of N9H30
Function
GPG11
RS-485_6_DI
GPG12
RS-485_6_RO
GPG12
RS-485_6_ENB
SW6~8: 1-2 short for RS-485_6 function and connected to 2P terminal (CON5 and J5)
SW6~8: 2-3 short for I2S function and connected to NAU88C22 (U10).
Power on setting (SW4, S2~9).
SW
State
Function
SW4.2/SW4.1
ON/ON
Boot from USB
SW4.2/SW4.1
ON/OFF
Boot from eMMC
SW4.2/SW4.1
OFF/ON
Boot from NAND Flash
SW4.2/SW4.1
OFF/OFF
Boot from SPI Flash
SW
State
Function
S2
Short
System clock from
12MHz crystal
S2
Open
System clock from
UPLL output
SW
State
Function
S3
Short
Watchdog Timer OFF
S3
Open
Watchdog Timer ON
SW
State
Function
S4
Short
GPJ[4:0] used as GPIO
pin
S4
Open
GPJ[4:0] used as JTAG
ICE interface

NuMaker-emWin-N9H30
Apr. 22, 2021 Page 14 of 36 Rev 2.12
NUMAKER-EMWIN-N9H30 USER MANUAL
SW
State
Function
S5
Short
UART0 debug message
ON
S5
Open
UART0 debug message
OFF
SW
State
Function
S7/S6
Short/Short
NAND Flash page size
2KB
S7/S6
Short/Open
NAND Flash page size
4KB
S7/S6
Open/Short
NAND Flash page size
8KB
S7/S6
Open/Open
Ignore
SW
State
Function
S9/S8
Short/Short
NAND Flash ECC type
BCH T12
S9/S8
Short/Open
NAND Flash ECC type
BCH T15
S9/S8
Open/Short
NAND Flash ECC type
BCH T24
S9/S8
Open/Open
Ignore
CMOS Sensor connector (CON9, SW9~10)
Connector
GPIO pin of N9H30
Function
CON9.1
-
VSS
CON9.2
-
VSS
CON9.3
-
Power 3.3V
CON9.4
-
Power 3.3V
CON9.5
-
-
CON9.6
-
-
CON9.7
GPI4
S_PCLK
CON9.8
GPI3
S_CLK
CON9.9
GPI8
S_D0
CON9.10
GPI9
S_D1

NuMaker-emWin-N9H30
Apr. 22, 2021 Page 15 of 36 Rev 2.12
NUMAKER-EMWIN-N9H30 USER MANUAL
CON9.11
GPI10
S_D2
CON9.12
GPI11
S_D3
CON9.13
GPI12
S_D4
CON9.14
GPI13
S_D5
CON9.15
GPI14
S_D6
CON9.16
GPI15
S_D7
CON9.17
GPI6
S_VSYNC
CON9.18
GPI5
S_HSYNC
CON9.19
GPI0
S_PWDN
CON9.20
GPI7
S_nRST
CON9.21
GPG2
I2C1_C
CON9.22
GPG3
I2C1_D
CON9.23
-
VSS
CON9.24
-
VSS
SW9~10: 1-2 short for CAN_0 function and connected to 2P terminal (CON11).
SW9~10: 2-3 short for CMOS sensor function and connected to CMOS sensor
connector (CON9).
CAN_0 selection (CON11, SW9~10):
GPIO pin of N9H30
Function
GPI4
CAN_0_TXD
GPI3
CAN_0_RXD
SW9~10: 1-2 short for CAN_0 function and connected to 2P terminal (CON11)
SW9~10: 2-3 short for CMOS sensor function and connected to CMOS sensor
connector (CON9, CON10).
USB0 Device/HOST Micro-AB connector (CON14), By CON14 pin4 ID=1 is device, ID=0
is HOST
USB1 for USB HOST with type-A connector (CON15)
RJ45_0 connector with LED indicator (CON12), RMII PHY with IP101GR (U14)
RJ45_1 connector with LED indicator (CON13), RMII PHY with IP101GR (U16)
Micro-SD/TF card slot (CON3)
SOC CPU: nuvoTon N9H30F61IEC (U5)
Battery power for RTC 3.3V powered (BT1, J1), can detect voltage by ADC0
RTC power has 3 sources:
Share with 3.3V I/O power.
Battery socket for CR2032 (BT1).
External connector (J1).
Board version 2.1

NuMaker-emWin-N9H30
Apr. 22, 2021 Page 16 of 36 Rev 2.12
NUMAKER-EMWIN-N9H30 USER MANUAL
RS-232_2 DB9
(CON6, J6)
CAN_0 Terminal
(CON11, SW9~10)
RS-232_0 DB9
(CON2, J3)
Expand Port
(CON7)
Earphone Output
(CON4)
Buzzer
(BZ1)
System Reset SW
(SW5)
SPI Flash
(U7, U8)
Power Protection IC
(U1)
JTAG ICE
(J2)
+5V In
(CON1)
Board Version 2.1 Micro SD Slot
(CON3)
RJ45_1
(CON13)
RJ45_0
(CON12)
USB1 HOST
(CON15)
USB0 Device/HOST
(CON14)
CMOS Sensor Connector
(CON9, SW9~10)
Power On Setting
(SW4, S2~9)
RS-485_6 Terminal
(CON5, J5, SW6~8)
RMII PHY
(U14, U16)
N9H30F61IEC
(U5)
RTC Battery
(BT1, J1)
Speaker Output
(J4)
Figure 2-2 NuMaker-emWin-N9H30 Board (Rear View)

NuMaker-emWin-N9H30
Apr. 22, 2021 Page 17 of 36 Rev 2.12
NUMAKER-EMWIN-N9H30 USER MANUAL
2.4 NuMaker-TFT-LCD7 －Front View
Figure 2-3 shows the main components and connectors from the Front view of NuMaker-TFT-
LCD7 board.
7”resolution 800x480 4W resistive touch panel for 24bits RGB888 interface
Figure 2-3 NuMaker-TFT-LCD7 Board (Front View)

NuMaker-emWin-N9H30
Apr. 22, 2021 Page 18 of 36 Rev 2.12
NUMAKER-EMWIN-N9H30 USER MANUAL
2.5 NuMaker-TFT-LCD7 －Rear View
Figure 2-4 shows the main components and connectors from the rear view of NuMaker-TFT-
LCD7 board.
NuMaker-emWin-N9H30 and NuMaker-TFT-LCD7 combination connector (CON1).
Figure 2-4 NuMaker-TFT-LCD7 Board (Rear View)

NuMaker-emWin-N9H30
Apr. 22, 2021 Page 19 of 36 Rev 2.12
NUMAKER-EMWIN-N9H30 USER MANUAL
2.6 NuMaker-emWin-N9H30 and NuMaker-TFT-LCD7 PCB Placement
The following figure shows NuMaker-emWin-N9H30 and NuMaker-TFT-LCD7 PCB placement.
Figure 2-6 NuMaker-emWin-N9H30 Front PCB Placement

NuMaker-emWin-N9H30
Apr. 22, 2021 Page 20 of 36 Rev 2.12
NUMAKER-EMWIN-N9H30 USER MANUAL
Figure 2-7 NuMaker-emWin-N9H30 Back PCB Placement