Nuvoton NUTINY-SDK-M051 User manual

NuTiny-SDK-M051 User’s Manual
1
NuTiny-SDK-M051 User’s Manual
For NuMicro M051™Series
The information described in this document is the exclusive intellectual property of
Nuvoton Technology Corporation and shall not be reproduced without permission from Nuvoton.
Nuvoton is providing this document only for reference purposes of NuMicro™microcontroller based system design. Nuvoton
assumes no responsibility for errors or omissions.
All data and specifications are subject to change without notice.
For additional information or questions, please contact: Nuvoton Technology Corporation.
Downloaded from Arrow.com.

NuTiny-SDK-M051 User’s Manual
2
1Overview .....................................................................................................3
2NuTiny-SDK-M051 introduction.......................................................................3
2.1 NuTiny -SDK-M051 Jumper Description ....................................................................4
2.2 Pin Assignment for Extended Connector....................................................................5
2.3 NuTiny-SDK-M051 PCB Placement...........................................................................5
3How to start NuTiny -SDK-M051 on the Keil uVision®IDE...................................6
3.1 Keil uVision®IDE Software Download & Install ..........................................................6
3.2 Nuvoton Nu-Link Driver Download & Install...............................................................6
3.3 Hardware Setup....................................................................................................6
3.4 Smpl_NuTiny-M051 Example Program......................................................................7
4How to start NuTiny-SDK-M051 on the IAR Embedded Workbench.......................8
4.1 IAR Embedded Workbench Software Download &Install ..............................................8
4.2 Nuvoton Nu-Link Driver Download & Install...............................................................8
4.3 Hardware Setup....................................................................................................8
4.4 Smpl_NuTiny-M051 Example Program......................................................................9
5M052_TINY-EVB Schematic .......................................................................... 10
6To Download NuMicro™Family Releated Files From Nuvoton Company............... 11
6.1 To Download NuMicro™Keil uVision®IDE driver...................................................... 11
6.2 To Download NuMicro™IAR EWARM driver .............................................................. 12
6.3 To Download NuMicro™M051 series BSP Software Library ........................................ 13
7Revision History.......................................................................................... 13
Downloaded from Arrow.com.Downloaded from Arrow.com.

NuTiny-SDK-M051 User’s Manual
3
1Overview
NuTiny-SDK-M051 is the specific development tool for NuMicro M051™series –M052/M054/M058/M0516. Users can
use NuTiny-SDK-M051 to develop and verify the application program easily.
NuTiny-SDK-M051 includes 2 portions. One is M052_Tiny-EVB and the other is Nu-Link-Me. M052_Tiny-EVB is
evaluation board and Nu-Link-Me is its Debug Adaptor. Thus, users do not need additional ICE equipment.
2NuTiny-SDK-M051 introduction
NuTiny-SDK-M051 can support NuMicro M051™series. Figure 2-1 is NuTiny-SDK-M051 for M051 series and the left
portion is called M052-TINY-EVB and the right portion is Debug Adaptor called Nu-Link-Me.
M052-TINY-EVB is similar to other development board. Users can use it to develop and verify applications to emulate
the real behavior. In fact, the real chip M0516LAN is mounted on the board. The on board chip covers M052, M054 and
M058’s features. The M052_Tiny-EVB can be a real system controller to design user target system.
Nu-Link-Me is a Debug Adaptor. The Nu-Link-Me Debug Adaptor connects your PC's USB port to your target
system (via Serial Wired Debug Port) and allows you to program and debug embedded programs on the target
hardware. To use Nu-Link-Me Debug adaptor with Keil or IAR Please refer to “Nuvoton NuMicro™IAR ICE driver user
manual “ or Nuvoton NuMicro™Keil ICE driver user manual” in detail.
Figure 2-1 NuTiny-SDK-M051 (Green Color PCB Board)
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

NuTiny-SDK-M051 User’s Manual
4
2.1 NuTiny -SDK-M051 Jumper Description
2.1.1 Power Setting
zJP2: VCC5 Voltage connecter in M052_TINY-EVB
zJ2: USB port in Nu-Link-Me
POWER model J1 USB port J2 USB port JP2 VCC5 MCU Voltage
Model 1 X Connect to PC DC 5V output DC 5V
Model 2 X X DC 2.8-5.5V input Voltage by VCC input
X: Not use.
2.1.2 Debug Connector
zJP4: Target ICE Connector in M052_TINY-EVB
zJP8: Nuvoton ICE Connector in Nu-Link-Me
2.1.3 USB Connecter
zJ1: mini USB Connecter in M052_TINY-EVB
zJ2: mini USB Connecter in Nu-Link-Me
2.1.4 Extended Connecter
zJP1, JP5, JP6 and JP7: Show all of chip pins in M052_TINY-EVB
2.1.5 Reset Button
zSW1: Reset button in M052_TINY-EVB
2.1.6 Power Connecter
zJP2: VCC connecter in M052_TINY-EVB
zJP3: GND connecter in M052_TINY-EVB
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

NuTiny-SDK-M051 User’s Manual
5
2.2 Pin Assignment for Extended Connector
M052_TINY-EVB provides M0516LAN on board and the extended connector for LQFP-48 pin. Table
2-1 is the pin assignment for M0516LAN.
Pin No Pin Name Pin No Pin Name
01 MOSI_0,AIN5,P1.5 25 P2.5,AD13,PWM5
02 MISO_0,AIN6,P1.6 26 P2.6,AD14,PWM6
03 SCLK0,AIN7,P1.7 27 P2.7,AD15,PWM7
04 /RST 28 P4.4,/CS
05 P3.0,RXD 29 P4.5,ALE
06 AVSS 30 P4.6,ICE_CLK
07 P3.1,TXD 31 P4.7,ICE_DATA
08 P3.2,/INT0,STADC 32 P0.7,AD7,SCLK1
09 P3.3,/INT1,MCLK 33 P0.6,AD6,MISO_1
10 P3.4, T0,SDA 34 P0.5,AD5,MOSI_1
11 P3.5,T1,SCL 35 P0.4,AD4,/SS1
12 P4.3,PWM3 36 P4.1,PWM1
13 P3.6,/WR,CKO 37 P0.3,AD3,RTS0
14 P3.7,/RD 38 P0.2,AD2,CST0
15 XTAL2 39 P0.1,AD1,RTS1
16 XTAL1 40 P0.0,AD0,CTS1
17 VSS 41 VDD
18 LDO_CAP 42 AVDD
19 P2.0,AD8,PWM0 43 P1.0,AIN0,P1.0
20 P2.1,AD9,PWM1 44 P1.1,AIN1,T3
21 P2.2,AD10,PWM2 45 P1.2,AIN2,RXD1
22 P2.3,AD11,PWM3 46 P1.3AIN3,TXD1
23 P2.4,AD12,PWM4 47 P1.4,AIN4,/SS0
24 P4.0,PWM0 48 P4.2,PWM2
Table 2-1 pin assignment for M0516LAN
2.3 NuTiny-SDK-M051 PCB Placement
Users can refer Figure 2-2 for the NuTiny -SDK-M051 PCB placement.
Figure 2-2 NuTiny-SDK-M051 PCB Placement
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

NuTiny-SDK-M051 User’s Manual
6
3How to start NuTiny -SDK-M051 on the Keil uVision®IDE
3.1 Keil uVision®IDE Software Download & Install
Please connect to Keil company website (http://www.keil.com) to download the Keil uVision®IDE and install the
RVMDK.
3.2 Nuvoton Nu-Link Driver Download & Install
Please connect to Nuvoton company NuMicro™website ( http://www.nuvoton.com/NuMicro ) to download “NuMicro™
Keil uVision®IDE driver” file. Please refer the Chapter 6.1 for the detail download flow. When the download had
finished, please unzip the file and execute the “Nu-Link_Keil_Driver.exe” to install the driver.
3.3 Hardware Setup
The hardware setup is shown as Figure 3-1
Figure 3-1 NuTiny-SDK-M051 Hardware Setup
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

NuTiny-SDK-M051 User’s Manual
7
3.4 Smpl_NuTiny-M051 Example Program
This example demonstrates the ease of downloading and debugging an application on a NuTiny-SDK-M051 board.
The example can be found on the Figure 3-2 list directory.
Directory Project File
Figure 3-2 Smpl_NuTiny-M051 Example Directory
To use this example:
Start uVision
Open the Smpl_NuTiny-M051.uvproj project file
Project-Open
Compile and link the Smpl_NuTiny-M051
application
Project - Build
Program the application into on-chip Flash ROM
Flash – Download
The LED will toggle on the M052_TINY-EVB board.
Start debug mode
Using the debugger commands, you may:
Single step through code
Run the application\
Review variables in the watch window
Reset the device to re-run the application
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

NuTiny-SDK-M051 User’s Manual
8
4How to start NuTiny-SDK-M051 on the IAR Embedded Workbench
4.1 IAR Embedded Workbench Software Download &Install
Please connect to IAR company website (http:// www.iar.com) to download the IAR Embedded Workbench and install the
EWARM.
4.2 Nuvoton Nu-Link Driver Download & Install
Please connect to Nuvoton company NuMicro™ website ( www.nuvoton.com/NuMicro) to download “NuMicro™IAR
ICE driver user manual” file. Please refer the 6.2 for the detail download flow. When the download had finished, please
unzip the file and execute the “Nu-Link_IAR_Driver.exe” to install the driver.
4.3 Hardware Setup
The hardware setup is shown as Figure 3-1
Figure 4-1 NuTiny- SDK-M051 Hardware Setup
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

NuTiny-SDK User’s Manual
9
4.4 Smpl_NuTiny-M051 Example Program
This example demonstrates the ease of downloading and debugging an application on a NuTiny-SDK-M051 board.
The example can be found on the Figure 3-2 list directory. (Samples code can be download from Nuvoton website)
Directory Project File
Figure 4-2 Smpl_NuTiny-M051 Example Directory
To use this example:
Start IAR Embeded Workbench
Open the Smpl_NuTiny-M051.eww workspace file
File-Open-Workspace
Compile and link the Smpl_NuTiny-M051
application
Project - Make
Program the application into on-chip Flash ROM
Project – Download and Debug
The I/O will toggle on the M052_TINY-EVB board.
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

NuTiny-SDK-M051 User’s Manual
10
5M052_TINY-EVB Schematic
CB1
0.1u
C0603
DAVDD
R11
10K 0805R
12
IO
KPT-2012
KP-2012 NET2
VCC
PIN13
U1
M052 LQFP 48
NCU120_LQFP_48
AIN1/T2/P1.1 44
AIN2/RXD1/P1.2 45
AIN3/TXD1/P1.3 46
AIN3/SS0/P1.4 47
P4.2 48
MOSI_0/AIN5/P1.5
1
MISO_0/AIN6/P1.6
2
SCLK0/AIN7/P1.7
3
VSS
17
LDO_CAP
18
P2.0/AD8/PWM0
19
P2.1/AD9/PWM1
20
P2.2/AD10/PWM2
21
P2.3/AD11/PWM3
22
P2.4/AD12/PWM4
23
P4.0
24
P2.6/AD14/PWM6 26
P4.6/ICE_CLK 30 P4.7/ICE_DAT 31
P0.7/AD7/SCLK1 32
P0.6/AD6/MISO_1 33 P0.5/AD5/MOSI_1 34
P0.4/AD4/SS1 35
P4.1 36
P0.3/AD3/RTS0 37
P0.2/AD2/CTS0 38
P0.1/AD1/RTS1 39
RST
4
RXD/P3.0
5
AVSS
6
MCLK/INT1/P3.3
9TXD/P3.1
7
INT0/P3.2
8
SDA/T0/P3.4
10
SCL/T1/P3.5
11
PWM3/P4.3
12
P3.6/WR/CKO
13
P4.5/ALE 29
P4.4/CS 28
AIN0/T2/P1.0 43
AVDD 42
VDD 41
P0.0/AD0/CTS1 40
P3.7/RD
14
XTAL1
16 XTAL2
15
P2.5/AD13/PWM5 25 P2.7/AD15/PWM7 27
PIN48
C2 10uF
TANT-B
12
POWER
KPT-2012
KP-2012
PR
10K 0805R
VCC
NET3
D12MI
PIN36
DAVDD
PIN35 PIN34
PIN1
PIN33
PIN2
PIN32
PIN3
PIN31 TICEDAT
PIN4TICERST
PIN30 TICECLK
PIN5
PIN29
PIN6
PIN28
PIN7
ADAVSS
From ICE Bridge's USB Power
PIN8
PIN27
ICE INTERFACE
TICEDAT TICERST
VCC
JP4
HEADER 5X2 HEADER5x2
1 2 3 4 5 6 7 8 910
TICECLK
PIN9
VCC
C1
10uF/10V
TANT-A
R1 10K
0805R
Reset Circuit
TICERST
SW1
PUSH BOTTOM
SW
PIN26
PIN10
C5
20p
0805C
X2
12MHz
XTAL3-1
R4
1M
0805R
D12MO
C3
20p
0805C
R2 33
0805R
NET1 PIN11 PIN25
JP2
HEADER 2 HEADER2
1 2
TP1 SIP/1P
1
JP3
HEADER 2 HEADER2
1 2
PIN12
PIN18
Title Size Document Number Rev Date: Sheet of
M052_TINY_V002.DSN 004
Nuvoton M052_TINY-EVB Board Versin 002
11Tuesday, August 10, 2010
TP2 SIP/1P
1
TICERST
VCC
ADAVSS
D12MO D12MI
VCC
L1
L0603
DAVDD
TP3 SIP/1P
1
JP5
HEADER 6X2 HEADER6X2
1 2 3 4 5 6 7 8 910 11 12
PIN2PIN1 PIN4PIN3 PIN8 PIN6PIN5
PIN11 PIN10PIN9 PIN7
PIN12
PIN14
JP6 HEADER 6X2 HEADER6X2
12 34 56 78 910 1112
PIN26 PIN25
PIN29
PIN28 PIN27
PIN31
PIN30
PIN33
PIN32
PIN35
PIN34 PIN36
JP1
HEADER 6X2 HEADER6X2
12 34 56 78 910 1112
PIN39
PIN38 PIN37
PIN41
PIN40
PIN45
PIN44 PIN43
PIN42
PIN46 PIN47
PIN15
L2
L0603
PIN16
Crystal
PIN46
PIN40
PIN48
PIN44
PIN47
PIN41
PIN39
PIN38
PIN37
PIN45
PIN43
PIN42
PIN13
TICECLK
TICEDAT TICERST TICERST
TICEDAT TICECLK
JP7
HEADER 6X2 HEADER6X2
1 2
3 4
5 6
7 8
910
11 12
PIN17
PIN20
PIN19
PIN18
PIN16PIN15 PIN14PIN13
PIN21 PIN20PIN19 PIN18PIN17
PIN24PIN23 PIN22
PIN21
PIN24
PIN23
PIN22
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

NuTiny-SDK-M051 User’s Manual
11
6To Download NuMicro™Family Releated Files From Nuvoton Company
6.1 To Download NuMicro™Keil uVision®IDE driver
Step1
To connect to the Nuvoton NuMicro™Website: http://www.nuvoton.com/NuMicro
Step2
Step 3
Step 4
To download the :uMicro Keil uVision®IDE driver
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

NuTiny-SDK-M051 User’s Manual
12
6.2 To Download NuMicro™IAR EWARM driver
Step1
To connect to the Nuvoton NuMicro™Website: http://www.nuvoton.com/NuMicro
Step2
Click here to enter
Devlopment Tools page
Step 3
Step 4
To download the NuMicro™IAR Embeded Workbench®driver
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

NuTiny-SDK-M051 User’s Manual
13
6.3 To Download NuMicro™M051 series BSP Software Library
Step1
To connect to the Nuvoton NuMicro™Website: http://www.nuvoton.com/NuMicro
Step2
Step 3
To download the NuMicro M051™series software library
7Revision History
Version Date Page Description
1.0 Aug. 20, 2010 -- Initial Issued
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

NuTiny-SDK-M051 User’s Manual
14
Important Notice
Nuvoton products are not designed, intended, authorized or warranted for use as components in systems or
equipment intended for surgical implantation, atomic energy control instruments, airplane or spaceship
instruments, transportation instruments, traffic signal instruments, combustion control instruments, or for other
applications intended to support or sustain life. Further more, Nuvoton products are not intended for applications
wherein failure of Nuvoton products could result or lead to a situation wherein personal injury, death or severe
property or environmental damage could occur.
Nuvoton customers using or selling these products for use in such applications do so at their own risk and agree
to fully indemnify Nuvoton for any damages resulting from such improper use or sales.
Please note that all data and specifications are subject to change without notice. All the trademarks of products
and companies mentioned in this datasheet belong to their respective owners.
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.