NuWave Brio 10Q User manual

NuWave®
Brio™Healthy Digital
10Q Air Fryer
Owner’s Manual

8 9
Owner's Manual Owner's Manual
IMPORTANT SAFEGUARDS
READ ALL INSTRUCTIONS
When using electrical units, basic safety precautions should always be
followed including the following:
1. Do not touch hot surfaces.
2. To protect against electrical shock, do not immerse cord, plugs, or the unit
in water or other liquid.
3. Close supervision is necessary when any unit is used by or near children.
4. Unplug from outlet when not in use and before cleaning. Allow to cool
before putting on or taking off parts.
5. The use of other accessories that are not intended to be use with this unit is
not recommended. Doing so may damage the unit and can cause accidents.
6. NOT INTENDED FOR OUTDOOR USE.
7. Do not let cord hang over edge of table or counter, or touch hot surface.
8. Do not place on or near a hot gas, electric burner and or in a heated oven.
9. Extreme caution must be used when moving unit containing hot oil or other
hot liquids.
10. To disconnect, turn any control “OFF”, then remove plug from the wall outlet.
11. Never put the appliance against the wall or other appliances. There should
be at least 3 inches of free space for the back side. Left/right sides and the
upper side of the appliance. Do not place anything on top of appliance.
12. During air frying, hot steam is released from the air outlet opening. Keep
your hands and face distance from the steam and from the air outlet
opening. Also, be careful of hot steam and air when you remove the Fry Pan
Basket from the appliance.
SAVE THESE INSTRUCTIONS
CAUTION
• Always put the ingredients to be fried in the Fry Pan Basket to
prevent direct contact with the heating components.
• Do not cover the air inlet and outlet opening while the appliance
is operating.
• Do not pour oil into the Base Tray, this may create a re hazard.
• Never touch the inside of the appliance while it is operating.
WARNING
Please immediately cut off circuit and send unit to our
Customer Service Department in case of other problems.
1-877-689-2838 • [e-mail]
DO NOT USE THE UNIT FOR OTHER THAN INTENDED USE.
Note: Put the appliance on a surface that is horizontal, even and stable.
This appliance is intended for normal, household use. It is not intended to be used
in environments such as staff kitchens, shops. Ofces or other work environments.
1. Do not place the unit close to ammable materials heating units or wet
environments.
2. Height of ingredients placed in the Fry Pan Basket should comply with the
directions listed under “Operation Instructions”.
3. Do not replace with other parts that are not designed specically for the
NuWave Digital Brio 10Q Digital Air Fryer.
4. Do not put any other cooking pans in the Fry Pan Basket. Do not replace any
parts with other containers.
5. If a lot of smoke is escaping from the air vent during operation, unplug the
unit immediately and contact customer service.*
6. Do not move the unit while in operation. Only after the NuWave Digital Brio
10Q Digital Air Fryer has completely cooled down should you attempt to
move it. Always wait for the NuWave Brio Healthy Digital 10Q Air Fryer to
cool down prior to handling it.
7. Never use a towel to block the vent.
8. If any troubles arise during operation, any necessary service must be done
by NuWave, LLC or authorized by the manufacturer for repairs.
9. Do not disassemble the unit on your own or replace any parts.
10. Do not use metal utensils with the coated Fry Pan Basket as this can
damage the surface.
11. If the power cord is damaged, do not attempt to operate the unit.*
12. Keep the unit out of reach of children when the unit is operating or
cooling down.
13. Keep hands and face away from the venting outlet or where heat or steam
is being released.
14. Make sure NuWave Brio Healthy Digital 10Q. Air Fryer is always clean prior to
cooking.
15. It is normal for some smoke to escape the unit when heating for the rst time.
*Customer Service Department at 1-877-689-2838 • [e-mail]

8 9
Owner's Manual Owner's Manual
IMPORTANT SAFEGUARDS
READ ALL INSTRUCTIONS
When using electrical units, basic safety precautions should always be
followed including the following:
1. Do not touch hot surfaces.
2. To protect against electrical shock, do not immerse cord, plugs, or the unit
in water or other liquid.
3. Close supervision is necessary when any unit is used by or near children.
4. Unplug from outlet when not in use and before cleaning. Allow to cool
before putting on or taking off parts.
5. The use of other accessories that are not intended to be use with this unit is
not recommended. Doing so may damage the unit and can cause accidents.
6. NOT INTENDED FOR OUTDOOR USE.
7. Do not let cord hang over edge of table or counter, or touch hot surface.
8. Do not place on or near a hot gas, electric burner and or in a heated oven.
9. Extreme caution must be used when moving unit containing hot oil or other
hot liquids.
10. To disconnect, turn any control “OFF”, then remove plug from the wall outlet.
11. Never put the appliance against the wall or other appliances. There should
be at least 3 inches of free space for the back side. Left/right sides and the
upper side of the appliance. Do not place anything on top of appliance.
12. During air frying, hot steam is released from the air outlet opening. Keep
your hands and face distance from the steam and from the air outlet
opening. Also, be careful of hot steam and air when you remove the Fry Pan
Basket from the appliance.
SAVE THESE INSTRUCTIONS
CAUTION
• Always put the ingredients to be fried in the Fry Pan Basket to
prevent direct contact with the heating components.
• Do not cover the air inlet and outlet opening while the appliance
is operating.
• Do not pour oil into the Base Tray, this may create a re hazard.
• Never touch the inside of the appliance while it is operating.
WARNING
Please immediately cut off circuit and send unit to our
Customer Service Department in case of other problems.
1-877-689-2838 • [e-mail]
DO NOT USE THE UNIT FOR OTHER THAN INTENDED USE.
Note: Put the appliance on a surface that is horizontal, even and stable.
This appliance is intended for normal, household use. It is not intended to be used
in environments such as staff kitchens, shops. Ofces or other work environments.
1. Do not place the unit close to ammable materials heating units or wet
environments.
2. Height of ingredients placed in the Fry Pan Basket should comply with the
directions listed under “Operation Instructions”.
3. Do not replace with other parts that are not designed specically for the
NuWave Digital Brio 10Q Digital Air Fryer.
4. Do not put any other cooking pans in the Fry Pan Basket. Do not replace any
parts with other containers.
5. If a lot of smoke is escaping from the air vent during operation, unplug the
unit immediately and contact customer service.*
6. Do not move the unit while in operation. Only after the NuWave Digital Brio
10Q Digital Air Fryer has completely cooled down should you attempt to
move it. Always wait for the NuWave Brio Healthy Digital 10Q Air Fryer to
cool down prior to handling it.
7. Never use a towel to block the vent.
8. If any troubles arise during operation, any necessary service must be done
by NuWave, LLC or authorized by the manufacturer for repairs.
9. Do not disassemble the unit on your own or replace any parts.
10. Do not use metal utensils with the coated Fry Pan Basket as this can
damage the surface.
11. If the power cord is damaged, do not attempt to operate the unit.*
12. Keep the unit out of reach of children when the unit is operating or
cooling down.
13. Keep hands and face away from the venting outlet or where heat or steam
is being released.
14. Make sure NuWave Brio Healthy Digital 10Q. Air Fryer is always clean prior to
cooking.
15. It is normal for some smoke to escape the unit when heating for the rst time.
*Customer Service Department at 1-877-689-2838 • [e-mail]

10 11
Owner's Manual Owner's Manual
PARTS DESCRIPTION
1
1. Air Fryer power base
Part #: 37257
2. Base Tray
Part #: 37251
3. Rotisserie Fork
Part #: 37252
4. Skewer
Part #: 37253
5. Reversible Wire Rack
Part #: 37254
6. Fry Pan Basket Net
Part #: 37255
7. Non-Stick Inner Basket
Part #: 37256
8. Lid Unlock Button
9. Lid Handle
10. Vents
11. Control Panel
12. Vent
13. Heater
14. Shaft Support Hole
4 5
AIR FRYER PREPARATION
Before Use:
1. Remove all the packaging materials.
2. Remove the glue and labels on the appliance.
3. Clean the Base Tray, Rotisserie Fork, Skewer, Reversible Wire Rack, Fry
Pan Basket Net, and Non-Stick Inner Basket thoroughly with hot water, a
nonabrasive sponge and a mild dish detergent, or in the dishwasher, top
rack only.
4. Wipe the inside and outside of the appliance with a wet cloth. Do not
immerse the appliance in water.
Note: This appliance cooks using hot air. DO NOT ll the unit with oil.
Operation Preparation:
1. Place the appliance on a level, even, and stable heat-resistant surface.
2. Place the Base Tray and Fry Pan Basket in the NuWave Brio Healthy
Digital 10Q Air Fryer.
3. Plug the appliance into a standard wall socket. The power plug is included in
the package.
Note: Do not cover or block the vent located on the top of the NuWave Brio
Healthy Digital 10Q Air Fryer. Doing so can prevent proper ventilation and will
adversely affect the cooking results.
2
67
3
9
11
10
12
13
14 8
1. To open the Top Cover, hold the Lid Handle
with one hand and make sure you hear "click"
sound to make sure secure the Top Cover
stay on the position.
How to lock/unlock Air Fryer
2. Place the Base Tray into the Brio 10Q by
holding the handles and make sure the
bottom of the Base Tray is dry and clean.
3. To close the Top Cover, hold the Lid Handle
wth one hand and use the other hand pull up
the Lid Unlock Button and slowly lower the Lid
down until it fully closes.

10 11
Owner's Manual Owner's Manual
PARTS DESCRIPTION
1
1. Air Fryer power base
Part #: 37257
2. Base Tray
Part #: 37251
3. Rotisserie Fork
Part #: 37252
4. Skewer
Part #: 37253
5. Reversible Wire Rack
Part #: 37254
6. Fry Pan Basket Net
Part #: 37255
7. Non-Stick Inner Basket
Part #: 37256
8. Lid Unlock Button
9. Lid Handle
10. Vents
11. Control Panel
12. Vent
13. Heater
14. Shaft Support Hole
4 5
AIR FRYER PREPARATION
Before Use:
1. Remove all the packaging materials.
2. Remove the glue and labels on the appliance.
3. Clean the Base Tray, Rotisserie Fork, Skewer, Reversible Wire Rack, Fry
Pan Basket Net, and Non-Stick Inner Basket thoroughly with hot water, a
nonabrasive sponge and a mild dish detergent, or in the dishwasher, top
rack only.
4. Wipe the inside and outside of the appliance with a wet cloth. Do not
immerse the appliance in water.
Note: This appliance cooks using hot air. DO NOT ll the unit with oil.
Operation Preparation:
1. Place the appliance on a level, even, and stable heat-resistant surface.
2. Place the Base Tray and Fry Pan Basket in the NuWave Brio Healthy
Digital 10Q Air Fryer.
3. Plug the appliance into a standard wall socket. The power plug is included in
the package.
Note: Do not cover or block the vent located on the top of the NuWave Brio
Healthy Digital 10Q Air Fryer. Doing so can prevent proper ventilation and will
adversely affect the cooking results.
2
67
3
9
11
10
12
13
14 8
1. To open the Top Cover, hold the Lid Handle
with one hand and make sure you hear "click"
sound to make sure secure the Top Cover
stay on the position.
How to lock/unlock Air Fryer
2. Place the Base Tray into the Brio 10Q by
holding the handles and make sure the
bottom of the Base Tray is dry and clean.
3. To close the Top Cover, hold the Lid Handle
wth one hand and use the other hand pull up
the Lid Unlock Button and slowly lower the Lid
down until it fully closes.

12 13
Owner's Manual Owner's Manual
• During cooking, Remaining time will countdown (“:” is
ashing), you can press "Cook Temp" to see the current cooking
temperature, the display will go back to the original cook time
countdown after 3 seconds.
Adjusting Time:
Default cooking time is 15 minutes.
1. Press "Cook Time", “00:15” and “TIME” will ash on display.
2. Adjust the cooking time by pressing the "+" and "-".
Sear Function:
Default cooking time is 8 minutes and default cooking
temperature is 400˚F.
1. Press “Sear”.
2. “00:08” and “TIME” will appear on the display and LED dot
above "Sear" will be lit. ":" will be ashing and countdown will
begin.
3. To clear the Sear function, press "Sear" again, "0" will be
displayed.
Note:
• Sear will always be the rst cooking function executed by the
NuWave Brio Digital Air Fryer.
• You cannot adjust the time or temperature of the Sear
Function.
“Preheat” Function:
The “Preheat” function ensures that the NuWave Brio Healthy
Digital 10Q. Air Fryer reaches the desired temperature before
you begin cooking your food. Press the “Preheat” button. The
control panel will display “0” and “Pre-Heat”.
Manually adjust the cooking temperature and time, then press
“Start/Pause”. Once you press “Start”, the desired temperature
will be ashing and "Pre-Heat" will be displayed.
Once the NuWave Brio Healthy Digital 10Qt. Air Fryer reaches
the set temperature, the control panel will display “Ready” and the
NuWave Brio Healthy Digital 10Qt. Air Fryer will beep once. The
NuWave Brio Healthy Digital 10Qt. Air Fryer will start a countdown
of 5 minutes and the number “5” will start ashing. It will remain at
this temperature for up to 5 minutes, or until you open and close
the lid, whichever comes rst.
Once the food has been added to the Fry Pan Basket, close the
lid. This will start the countdown on the set cooking time.
CONTROL PANEL OPERATION (Continued)
CONTROL PANEL OPERATION
Operation Functions - On/Off Function:
Press “On/Off” once to turn the unit on. The control panel should
display “0” indicating that no cooking time or temperature has
been selected and the unit is powered on. Press “On/Off” again
to turn the unit off.
Start:
• Press “Start” once to begin cooking, ":15" will be displayed as well
as a fan icon, and the NuWave Brio Healthy Digital 10Qt. Air Fryer
will start to countdown. The default is 360˚F for 15 minutes.
Pause/Clear:
• To interrupt the cooking process, press “Pause/Clear” once.
• To cancel the cooking process or program, press “Pause/Clear”
again.
•Adjusting Temperature:
1. Default cooking temperature is 360ºF "360" on the display.
2. Press "Cook Temp" and “TEMP” will appear on display.
3. To adjust the cooking temperature by pressing "+" and "-".
Note:
• After setting the cooking temperature, if you want to change
the cooking temperature before you can start cooking, you can
adjust by "+" and "-".
Vent Switch
• Adjust the vent to the “close” position to help keep moisture within the unit.
• Adjust the vent to the “open” position to have the NuWave Brio Digital Air
Fryer function as a true air fryer.

12 13
Owner's Manual Owner's Manual
• During cooking, Remaining time will countdown (“:” is
ashing), you can press "Cook Temp" to see the current cooking
temperature, the display will go back to the original cook time
countdown after 3 seconds.
Adjusting Time:
Default cooking time is 15 minutes.
1. Press "Cook Time", “00:15” and “TIME” will ash on display.
2. Adjust the cooking time by pressing the "+" and "-".
Sear Function:
Default cooking time is 8 minutes and default cooking
temperature is 400˚F.
1. Press “Sear”.
2. “00:08” and “TIME” will appear on the display and LED dot
above "Sear" will be lit. ":" will be ashing and countdown will
begin.
3. To clear the Sear function, press "Sear" again, "0" will be
displayed.
Note:
• Sear will always be the rst cooking function executed by the
NuWave Brio Digital Air Fryer.
• You cannot adjust the time or temperature of the Sear
Function.
“Preheat” Function:
The “Preheat” function ensures that the NuWave Brio Healthy
Digital 10Q. Air Fryer reaches the desired temperature before
you begin cooking your food. Press the “Preheat” button. The
control panel will display “0” and “Pre-Heat”.
Manually adjust the cooking temperature and time, then press
“Start/Pause”. Once you press “Start”, the desired temperature
will be ashing and "Pre-Heat" will be displayed.
Once the NuWave Brio Healthy Digital 10Qt. Air Fryer reaches
the set temperature, the control panel will display “Ready” and the
NuWave Brio Healthy Digital 10Qt. Air Fryer will beep once. The
NuWave Brio Healthy Digital 10Qt. Air Fryer will start a countdown
of 5 minutes and the number “5” will start ashing. It will remain at
this temperature for up to 5 minutes, or until you open and close
the lid, whichever comes rst.
Once the food has been added to the Fry Pan Basket, close the
lid. This will start the countdown on the set cooking time.
CONTROL PANEL OPERATION (Continued)
CONTROL PANEL OPERATION
Operation Functions - On/Off Function:
Press “On/Off” once to turn the unit on. The control panel should
display “0” indicating that no cooking time or temperature has
been selected and the unit is powered on. Press “On/Off” again
to turn the unit off.
Start:
• Press “Start” once to begin cooking, ":15" will be displayed as well
as a fan icon, and the NuWave Brio Healthy Digital 10Qt. Air Fryer
will start to countdown. The default is 360˚F for 15 minutes.
Pause/Clear:
• To interrupt the cooking process, press “Pause/Clear” once.
• To cancel the cooking process or program, press “Pause/Clear”
again.
•Adjusting Temperature:
1. Default cooking temperature is 360ºF "360" on the display.
2. Press "Cook Temp" and “TEMP” will appear on display.
3. To adjust the cooking temperature by pressing "+" and "-".
Note:
• After setting the cooking temperature, if you want to change
the cooking temperature before you can start cooking, you can
adjust by "+" and "-".
Vent Switch
• Adjust the vent to the “close” position to help keep moisture within the unit.
• Adjust the vent to the “open” position to have the NuWave Brio Digital Air
Fryer function as a true air fryer.

14 15
Owner's Manual Owner's Manual
Note:
• If you open the lid at any point during the preheating stage,
the NuWave Brio Healthy Digital 10Qt. Air Fryer will automatically
pause, start a countdown of 5 minutes until you close the lid.
• If you cook another batch of food shortly after cooking in the
NuWave Brio Healthy Digital 10Qt. Air Fryer, you do not need to
use the “Preheat” Function as the NuWave Brio Healthy Digital
10Qt. Air Fryer will already be hot. If you wish to cook your food
longer, continue cooking in 2-3 minute increments until desired
consistency has been reached.
Warm Function:
Default cooking time is 2 hours and default cooking temperature
is 155ºF.
1. Press “Warm”.
2. “155F” and “WARM” will appear on the display.
3. To change the time, press “Cook Time” and “2:00” will appear
on the display. Press “+“ and “-” to increase or decrease the time.
4. Proceed with setting the cooking temperature and cooking
times.
Note:
• You can set the NuWave Brio Digital Air Fryer to Warm from 1
minute up to 24 hours.
• Warm will always be the last cooking function executed by the
NuWave Brio Digital Air Fryer.
Delay Function:
1. Press “Delay”.
2. “00:00” and “TIME” will appear on the display.
3. Press “+“ and “-” to increase or decrease the time.
4. Proceed with setting the cooking temperature and cooking
time.
Note:
• You can set the NuWave Brio Digital Air Fryer to Delay from 1
minute up to 4 hours.
• Delay will always be the rst function executed by the
NuWave Brio Digital Air Fryer.
Program Function:
The Program button represents Memory Entry and Memory
Recall.
1. Enter cooking recipe rst -> Press "Program" -> "+" and "-"
to choose number to save -> press "Program".
Press "Stage", then using the "+" and "-", achieve your
appropriate temperatures, times and additional stages
if necessary for your recipes. Once complete, press
"Program". "Program" will be ashing on the display, then
using the "+" and "-", conrm the program number you wish
to save to. Press "Program" again to store it, then press
"Start" or press "Pause/Clear" so you can Recall at a later
time. Up to 10 cooking functions may be stored with each
memory entry (cooking time, temperature).
2. Press "Program"-> "+" & "-" to choose number to save ->
press "Program" -> Enter cooking recipe -> Start.
Press "Program" (Program is ashing) and use "+" and
"-" to choose the number to save your program to. Press
"Program" again to conrm the number to save to. Press
"Stage", then use "+" and "-" to achieve your appropriate
temperatures, times and additional stages if necessary for
your recipes. Then press "Start" or press "Pause/Clear" so
you can Recall at a later time.
3. When the cooking process is done, you can also save them.
When the cooking process is done, Press "Program"
(Program is ashing) and use "+" and "-" to choose the
number to save your program. Press "Program" again to
conrm the number to save to. Now you can recall the same
recipe you just cooked.
NOTE: You may store up to 100 different entries (1-100)
Memory Recall —Press "Program". “000” will display. Then, use
"+" and "-" to select the appropriate numeral buttons to start the
desired program.
Stage Function:
1. Press "Stage" then “1 STAGE” and “0” will be on display.
You can enter desired cooking temp/time by pressing "Cook
Temp" or "Cook Time".
2. Press "Stage" again, then you can set desired cooking for the
second stage. “2 STAGE” will be on display.
3. You can enter up-to 10 stages (Stage 10 will show as “0”)
4. Press "Start" when you are done entering all the stages.
CONTROL PANEL OPERATION (Continued) CONTROL PANEL OPERATION (Continued)

14 15
Owner's Manual Owner's Manual
Note:
• If you open the lid at any point during the preheating stage,
the NuWave Brio Healthy Digital 10Qt. Air Fryer will automatically
pause, start a countdown of 5 minutes until you close the lid.
• If you cook another batch of food shortly after cooking in the
NuWave Brio Healthy Digital 10Qt. Air Fryer, you do not need to
use the “Preheat” Function as the NuWave Brio Healthy Digital
10Qt. Air Fryer will already be hot. If you wish to cook your food
longer, continue cooking in 2-3 minute increments until desired
consistency has been reached.
Warm Function:
Default cooking time is 2 hours and default cooking temperature
is 155ºF.
1. Press “Warm”.
2. “155F” and “WARM” will appear on the display.
3. To change the time, press “Cook Time” and “2:00” will appear
on the display. Press “+“ and “-” to increase or decrease the time.
4. Proceed with setting the cooking temperature and cooking
times.
Note:
• You can set the NuWave Brio Digital Air Fryer to Warm from 1
minute up to 24 hours.
• Warm will always be the last cooking function executed by the
NuWave Brio Digital Air Fryer.
Delay Function:
1. Press “Delay”.
2. “00:00” and “TIME” will appear on the display.
3. Press “+“ and “-” to increase or decrease the time.
4. Proceed with setting the cooking temperature and cooking
time.
Note:
• You can set the NuWave Brio Digital Air Fryer to Delay from 1
minute up to 4 hours.
• Delay will always be the rst function executed by the
NuWave Brio Digital Air Fryer.
Program Function:
The Program button represents Memory Entry and Memory
Recall.
1. Enter cooking recipe rst -> Press "Program" -> "+" and "-"
to choose number to save -> press "Program".
Press "Stage", then using the "+" and "-", achieve your
appropriate temperatures, times and additional stages
if necessary for your recipes. Once complete, press
"Program". "Program" will be ashing on the display, then
using the "+" and "-", conrm the program number you wish
to save to. Press "Program" again to store it, then press
"Start" or press "Pause/Clear" so you can Recall at a later
time. Up to 10 cooking functions may be stored with each
memory entry (cooking time, temperature).
2. Press "Program"-> "+" & "-" to choose number to save ->
press "Program" -> Enter cooking recipe -> Start.
Press "Program" (Program is ashing) and use "+" and
"-" to choose the number to save your program to. Press
"Program" again to conrm the number to save to. Press
"Stage", then use "+" and "-" to achieve your appropriate
temperatures, times and additional stages if necessary for
your recipes. Then press "Start" or press "Pause/Clear" so
you can Recall at a later time.
3. When the cooking process is done, you can also save them.
When the cooking process is done, Press "Program"
(Program is ashing) and use "+" and "-" to choose the
number to save your program. Press "Program" again to
conrm the number to save to. Now you can recall the same
recipe you just cooked.
NOTE: You may store up to 100 different entries (1-100)
Memory Recall —Press "Program". “000” will display. Then, use
"+" and "-" to select the appropriate numeral buttons to start the
desired program.
Stage Function:
1. Press "Stage" then “1 STAGE” and “0” will be on display.
You can enter desired cooking temp/time by pressing "Cook
Temp" or "Cook Time".
2. Press "Stage" again, then you can set desired cooking for the
second stage. “2 STAGE” will be on display.
3. You can enter up-to 10 stages (Stage 10 will show as “0”)
4. Press "Start" when you are done entering all the stages.
CONTROL PANEL OPERATION (Continued) CONTROL PANEL OPERATION (Continued)

16 17
Owner's Manual Owner's Manual
ROTISSERIE ASSEMBLY
1. Screw one Rotisserie Fork onto one end
of the Skewer as shown in Step 1.
2. Push the Skewer through the center of
the chicken or meat you wish to cook
(see Step 2) until the Rotisserie Fork
pierces the food.
3. Place the second Rotisserie Fork onto
the other end of the Skewer and push
it along the rod until it pierces the other
end of the chicken and then tighten the
screw in place as shown in Step 3.
4. Place the assembled Rotisserie Fork
into the Base Tray making sure that
the longer squared section at the end
of the Skewer engages with the Shaft
assembly hole on the main body of
the Cooker. Place the shorter squared
section on the Shaft Bracket (see Steps
4 and 5).
CAUTION: Always check that there is
sufcient space above and below for food to
rotate freely without causing an obstruction.
To assemble the chicken with Rotisserie kit, please follow the illustration
below:
Rotisserie Function:
1. Press "Rotisserie", "325F" and "temp" will be displayed and
LED dot above rotisserie will be ashing. Time is defaulted
to 1 hour. To change the temperature press "Cook Temp"
to adjust. To get out of rotisserie, press rotisserie again
until LED dot above rotisserie is no longer ashing, or press
"Pause/Clear".
2. Once Start is pressed and cook time has started, the dot
above rotisserie will be solid indicating that the rotisserie is
rotating.
3. To change time, after you press rotisserie, press cook time,
1:00 and time will be displayed and use the "+" and "-" to
achieve your desired time.
To use Rotisserie with stages:
1. Press "Stage", during that stage you can press rotisserie. 325˚F and
temp will be displayed and dot above rotisserie will be ashing. Time
is defaulted to 1 hour. To change the temperature, press cook temp to
adjust. To get out of rotisserie, press "Rotisserie" again until dot above
rotisserie is no longer ashing.
2. To change time, after you press "Rotisserie", press cook time, 1:00 and
time will be displayed and use the up and down arrow to achieve your
desired time.
3. Dot will be ashing until you press start or press stage to move onto the
next stage.
4. Once Start is pressed and cook time has started, the dot above rotisserie
will be solid during the stage you chose indicating that the rotisserie is
rotating during that stage.
Example set Rotisserie with Stages:
Rotisserie for 1 hour for 350˚F at Stage 2
1. Press "Stage", then set the cook time and temperature for 10 minutes at
400ºF.
2. Press "Stage", then Press "Rotisserie", press "Cook Time", use arrow till
you see 1 hour, press "Start". Dot above rotisserie is solid when you get to
stage 2.
1
4
2
3

16 17
Owner's Manual Owner's Manual
ROTISSERIE ASSEMBLY
1. Screw one Rotisserie Fork onto one end
of the Skewer as shown in Step 1.
2. Push the Skewer through the center of
the chicken or meat you wish to cook
(see Step 2) until the Rotisserie Fork
pierces the food.
3. Place the second Rotisserie Fork onto
the other end of the Skewer and push
it along the rod until it pierces the other
end of the chicken and then tighten the
screw in place as shown in Step 3.
4. Place the assembled Rotisserie Fork
into the Base Tray making sure that
the longer squared section at the end
of the Skewer engages with the Shaft
assembly hole on the main body of
the Cooker. Place the shorter squared
section on the Shaft Bracket (see Steps
4 and 5).
CAUTION: Always check that there is
sufcient space above and below for food to
rotate freely without causing an obstruction.
To assemble the chicken with Rotisserie kit, please follow the illustration
below:
Rotisserie Function:
1. Press "Rotisserie", "325F" and "temp" will be displayed and
LED dot above rotisserie will be ashing. Time is defaulted
to 1 hour. To change the temperature press "Cook Temp"
to adjust. To get out of rotisserie, press rotisserie again
until LED dot above rotisserie is no longer ashing, or press
"Pause/Clear".
2. Once Start is pressed and cook time has started, the dot
above rotisserie will be solid indicating that the rotisserie is
rotating.
3. To change time, after you press rotisserie, press cook time,
1:00 and time will be displayed and use the "+" and "-" to
achieve your desired time.
To use Rotisserie with stages:
1. Press "Stage", during that stage you can press rotisserie. 325˚F and
temp will be displayed and dot above rotisserie will be ashing. Time
is defaulted to 1 hour. To change the temperature, press cook temp to
adjust. To get out of rotisserie, press "Rotisserie" again until dot above
rotisserie is no longer ashing.
2. To change time, after you press "Rotisserie", press cook time, 1:00 and
time will be displayed and use the up and down arrow to achieve your
desired time.
3. Dot will be ashing until you press start or press stage to move onto the
next stage.
4. Once Start is pressed and cook time has started, the dot above rotisserie
will be solid during the stage you chose indicating that the rotisserie is
rotating during that stage.
Example set Rotisserie with Stages:
Rotisserie for 1 hour for 350˚F at Stage 2
1. Press "Stage", then set the cook time and temperature for 10 minutes at
400ºF.
2. Press "Stage", then Press "Rotisserie", press "Cook Time", use arrow till
you see 1 hour, press "Start". Dot above rotisserie is solid when you get to
stage 2.
1
4
2
3

18 19
Owner's Manual Owner's Manual
Remove the Base Tray before
cleaning:
To remove the Fry Pan Basket from
the Base Tray.
1. Lift the top cover and make
sure you hear "click" sound
to make sure secure the Top
Cover stay on the position.
2. Lift the Fry Pan Basket out of
the Base Tray.
• Unplug the appliance and make
sure it cools completely.
CARE & MAINTENANCE
Cleaning:
Clean the appliance after every use or in between a large amount of batches.
The Fry Pan Basket and the Base Tray have a non-stick coating with a stainless
steel Basket Net. Do not use metal utensils or harsh abrasives when cleaning as
this can damage the coating.
Note: Remove the Base Tray and Fry Pan Basket, place on a heat resistant
surface to help cool the appliance quicker.
1. Once cooled completely, clean the Fry Pan Basket and Base Tray with
a soft cleaning brush to remove any lingering food.
2. Use a damp cloth to wipe the outside of the appliance.
3. Clean the Fry Pan Basket, and inside components with a nonabrasive
sponge, hot water and mild detergent or place in the dishwasher.
Note: If using the dishwasher for the Base Tray, and Fry Pan
Basket it is recommended to use top rack only.
Tip: If there is residual food in the Base Tray, and Fry Pan Basket,
add some hot water and let it soak separately for about 10 minutes for
easier cleaning.
• Storage:
• Unplug the appliance and let it cool down completely.
• Make sure that all the parts are cleaned and dry.
Once cooled completely, clean the Fry Pan Basket and Base Tray
with a soft cleaning brush to remove any lingering food.
IMPORTANT - Do not immerse unit in water or attempt to cycle through
dishwasher. The outer surface may be cleaned by wiping carefully with a
damp dishcloth or sponge. Make sure unit has cooled completely prior
to cleaning.
TROUBLESHOOTING GUIDE
PROBLEM POSSIBLE CAUSE(S) RESOLUTION(S)
The NuWave Brio
Healthy Digital 10
Qt. Air Fryer does
not work.
The appliance is not
plugged in. Did not
press On/OFF button.
Fry Pan Basket is not
in the NuWave Brio
Healthy Digital 10Q.
Air Fryer.
Insert the plug into an
appropriate grounded power
socket. Press ON/OFF button
after settings are selected.
Place the Fry Pan Basket in
the NuWave Brio Healthy
Digital 10Q Air Fryer.
The ingredients
fried in the Fry Pan
Basket are not
completely cooked.
Too many ingredients
were used. The cooking
temperature is too low.
The cooking time is too
short.
Remove some ingredients
from the Fry Pan Basket.
Smaller batches are fried
more evenly. Fry at a
higher temperature. Set the
NuWave Brio Healthy Digital
10Q Air Fryer to fry for a
longer time.
The food is fried
unevenly.
Certain types of
ingredients need to be
shaken halfway through
the preparation time.
Ingredients that are on
the top need to be shaken
halfway through the
preparation time.
Fried snacks are
not crispy when
they come out of the
NuWave Brio Healthy
Digital 10Q Air Fryer.
You used a type of
snack meant to be
prepared in a traditional
deep fryer.
Use snacks designed to be
baked in a traditional oven,
or lightly brush some olive
oil onto the snacks for a
crispier result.
I cannot slide the Fry
Pan Basket into the
appliance properly.
The Fry Pan Basket is
overlled. The Fry Pan
Basket is not placed in
the Base Tray correctly.
Do not ll the Fry Pan
Basket more than 4/5. Push
the Fry Pan Basket down
into the Base Tray until you
hear a click.
White smoke is
coming out of the
product.
You are frying greasy
foods. The pan contains
greasy residue from
previous uses.
When you are preparing
greasy ingredients in the
NuWave Brio Healthy Digital
10Q Air Fryer, large amounts
of oil can smoke and inltrate
into the pan. The oil will
produce white smoke and
the frying pan might become
hotter than usual. This will not
affect the nal cooking effect.
White smoke is caused by
greasy heating up in the pan.
Make sure you clean the frying
pan properly after each use.

18 19
Owner's Manual Owner's Manual
Remove the Base Tray before
cleaning:
To remove the Fry Pan Basket from
the Base Tray.
1. Lift the top cover and make
sure you hear "click" sound
to make sure secure the Top
Cover stay on the position.
2. Lift the Fry Pan Basket out of
the Base Tray.
• Unplug the appliance and make
sure it cools completely.
CARE & MAINTENANCE
Cleaning:
Clean the appliance after every use or in between a large amount of batches.
The Fry Pan Basket and the Base Tray have a non-stick coating with a stainless
steel Basket Net. Do not use metal utensils or harsh abrasives when cleaning as
this can damage the coating.
Note: Remove the Base Tray and Fry Pan Basket, place on a heat resistant
surface to help cool the appliance quicker.
1. Once cooled completely, clean the Fry Pan Basket and Base Tray with
a soft cleaning brush to remove any lingering food.
2. Use a damp cloth to wipe the outside of the appliance.
3. Clean the Fry Pan Basket, and inside components with a nonabrasive
sponge, hot water and mild detergent or place in the dishwasher.
Note: If using the dishwasher for the Base Tray, and Fry Pan
Basket it is recommended to use top rack only.
Tip: If there is residual food in the Base Tray, and Fry Pan Basket,
add some hot water and let it soak separately for about 10 minutes for
easier cleaning.
• Storage:
• Unplug the appliance and let it cool down completely.
• Make sure that all the parts are cleaned and dry.
Once cooled completely, clean the Fry Pan Basket and Base Tray
with a soft cleaning brush to remove any lingering food.
IMPORTANT - Do not immerse unit in water or attempt to cycle through
dishwasher. The outer surface may be cleaned by wiping carefully with a
damp dishcloth or sponge. Make sure unit has cooled completely prior
to cleaning.
TROUBLESHOOTING GUIDE
PROBLEM POSSIBLE CAUSE(S) RESOLUTION(S)
The NuWave Brio
Healthy Digital 10
Qt. Air Fryer does
not work.
The appliance is not
plugged in. Did not
press On/OFF button.
Fry Pan Basket is not
in the NuWave Brio
Healthy Digital 10Q.
Air Fryer.
Insert the plug into an
appropriate grounded power
socket. Press ON/OFF button
after settings are selected.
Place the Fry Pan Basket in
the NuWave Brio Healthy
Digital 10Q Air Fryer.
The ingredients
fried in the Fry Pan
Basket are not
completely cooked.
Too many ingredients
were used. The cooking
temperature is too low.
The cooking time is too
short.
Remove some ingredients
from the Fry Pan Basket.
Smaller batches are fried
more evenly. Fry at a
higher temperature. Set the
NuWave Brio Healthy Digital
10Q Air Fryer to fry for a
longer time.
The food is fried
unevenly.
Certain types of
ingredients need to be
shaken halfway through
the preparation time.
Ingredients that are on
the top need to be shaken
halfway through the
preparation time.
Fried snacks are
not crispy when
they come out of the
NuWave Brio Healthy
Digital 10Q Air Fryer.
You used a type of
snack meant to be
prepared in a traditional
deep fryer.
Use snacks designed to be
baked in a traditional oven,
or lightly brush some olive
oil onto the snacks for a
crispier result.
I cannot slide the Fry
Pan Basket into the
appliance properly.
The Fry Pan Basket is
overlled. The Fry Pan
Basket is not placed in
the Base Tray correctly.
Do not ll the Fry Pan
Basket more than 4/5. Push
the Fry Pan Basket down
into the Base Tray until you
hear a click.
White smoke is
coming out of the
product.
You are frying greasy
foods. The pan contains
greasy residue from
previous uses.
When you are preparing
greasy ingredients in the
NuWave Brio Healthy Digital
10Q Air Fryer, large amounts
of oil can smoke and inltrate
into the pan. The oil will
produce white smoke and
the frying pan might become
hotter than usual. This will not
affect the nal cooking effect.
White smoke is caused by
greasy heating up in the pan.
Make sure you clean the frying
pan properly after each use.

20 21
Owner's Manual Owner's Manual
PROBLEM POSSIBLE CAUSE(S) RESOLUTION(S)
French fries are
fried unevenly in
the NuWave Brio
Healthy Digital 10Q
Air Fryer.
You did not soak the
potato sticks properly
before you fried them.
You did not use the
right potato type.
Soak potato sticks in a bowl
of water for at lea st 30
minutes, take them out and
dry them with paper towel.
Use fresh potatoes and
make sure they stay rm
during frying.
French fries are not
crispy when they
come out of the
NuWave Brio Healthy
Digital 10Q Air Fryer.
The crispiness of the
fries depends on the
amount of oil and water
in the fries.
Make sure you dry the potato
sticks properly before you add
the oil. Cut the potato sticks
smaller for a crispier result.
Add slightly more oil for a
crispier result.
If the unit needs to be replaced or returned to the manufacturer,
please contact our Customer Service Department at: 1-877-689-2838
[e-mail]
TROUBLESHOOTING GUIDE
Contact costumer service if any of these errors occur
Code
Error
E2 E1 E3
Sensor open
ended
Sensor short
circuit Over heat
WARRANTY
The NuWave Brio Healthy Digital 10Q Air Fryer
THE MANUFACTURER WARRANTS
The NuWave Brio Healthy Digital 10Qt. Air Fryer, including the Base Tray, and Fry Pan
Basket, are to be free from manufacturer defects.
All electrical components are warranted for 1 year from the date of purchase, under
normal household use, and when operated in accordance with the Manufacturer’s
written instructions. The Manufacturer will provide the necessary parts and labor to repair
any part of the NuWave Brio Healthy Digital 10Qt. Air Fryer at NuWave, LLC Service
Department. After the expiration of the warranty, the cost of the labor and parts will be the
responsibility of the owner.
THE WARRANTY DOES NOT COVER
The Limited Warranty is voided if repairs are made by an unauthorized dealer or the
serial number data plate is removed or defaced. Normal deterioration of nish due to
use or exposure is not covered by this Warranty. This Limited Warranty does not cover
failure, damages or inadequate performance due to accident, acts of God (such as
lightning), uctuations in electric power, alterations, abuse, misuse, misapplications,
corrosive type atmospheres, improper installation, failure to operate in accordance with
the Manufacturer’s written instructions, abnormal use or commercial use. NuWave, LLC
reserves the right to void the Limited Warranty, where allowable by law, for products
purchased from an unauthorized dealer.
TO OBTAIN SERVICE
The owner shall have the obligation and responsibility to: Pay for all services and parts
not covered by the warranty; Prepay the freight to and from Service Department for
any part or system returned under this warranty; Carefully package the product using
adequate padding material to prevent damage in transit. The original container is ideal
for this purpose. Include in the package the owner’s name, address, day time telephone
number, a detailed description of the problem, and your “RGA number.” (Call 1-877-
689-2838) or e-mail [e-mail] to obtain the RGA number (Return Goods
Authorization number). Provide the cooking system model & serial number and proof of
date of purchase (a copy of the receipt) when making claims under this warranty.
MANUFACTURER’S OBLIGATION
The Manufacturer’s obligation under this Limited Warranty is limited, to the extent
allowable by law, to repairing or replacing any part covered by this Limited Warranty
which upon examination is found to be defective under normal use. The Limited
Warranty is applicable only within the continental United States and only to the original
purchaser of the manufacturer’s authorized channels of distribution. THE LIMITED
WARRANTY MAY NOT BE ALTERED, VARIED OR EXTENDED EXCEPT BY A
WRITTEN INSTRUMENT EXECUTED BY THE MANUFACTURER. THE REMEDY OF
REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS LIMITED WARRANTY
IS EXCLUSIVE. IN NO EVENT SHALL THE MANUFACTURER BE LIABLE FOR ANY
CONSEQUENTIAL OR INCIDENTAL DAMAGES TO ANY PERSON, WHETHER OR
NOT OCCASIONED BY NEGLIGENCE OF THE MANUFACTURER, INCLUDING
WITHOUT LIMITATION, DAMAGES FOR LOSS OF USE, COSTS OF SUBSTITUTION,
PROPERTY DAMAGE, OR OTHER MONEY LOSS.
Some states do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitation exclusions may not apply. This Limited Warranty gives
specic legal rights, and there may also be other rights which vary from state to state.
EXCEPT AS OTHERWISE EXPRESSLY PROVIDED ABOVE, THE MANUFACTURER
MAKES NO WARRANTIES EXPRESSED OR IMPLIED ARISING BY LAW OR
OTHERWISE, INCLUDING WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE TO ANY OTHER
PERSON. READ YOUR OWNER’S MANUAL. IF YOU STILL HAVE ANY QUESTIONS
ABOUT OPERATION OR WARRANTY OF THE PRODUCT, PLEASE CONTACT
NUWAVE, LLC.
READ YOUR OWNER’S MANUAL: If you still have any questions about operation or
warranty of the product, please contact NuWave, LLC at:
1-877-689-2838 or e-mail [e-mail].