Oce 3122 User manual

Océ 3122
Addendum Copy
Addendum Océ 3122

Océ 3122 Copy
Copying Manual
This document provides information which is new or has changed compared
with the Océ 3121 manual.
Common remarks
■The Fax Monitor key is always displayed in the Basic Features screen for
copying.
■When using the Stack Bypass, press the [Paper Select] key and then the
[Stack Bypass] key.
■The Film Projector is not available with the Océ 3122.
Page 3-27, Notice and 3-29, step 3: To cancel [Number of Output PGS] and
change to [Copy Ratio(s)], cancel the Multi-page Enlarge mode using the
Reset key and then change the specification.
Page 3-35, Memo: If the ADF or RDF is used and there are an odd number of
originals, the back of the last page is left blank. (The machine’s counter does
not count the blank page as a copy).
Page 3-37, step and page -11, step 3: If you place your original on the
platen glass the following messages appear on the touch panel display:
“Copying the 2nd side...”
Place the 2nd original and press the Start key again.
“Copying the 1st side...”
Page 3- 5, Memo in step 2:
■You can staple copies manually after they have been sorted, by using the
Manual Staple Mode.
■If you are going to perform manual stapling for sorted copies of originals
placed on the platen glass, before copying turn Face Down Output “Off” and
then start copying from the last page.
Page -19, Memo in step 3: The image will shift in the exact opposite
direction of the selected arrow.
Page -36, step 3:
■When the RDF is attached: Select either [2 on 1], [4 on 1] or [2 on
1/Two-sided], then press the [Ok] key.

Addendum Océ 3122
Notice: Only [2 on 1] can be selected when the originals are placed
horizontally.
■When RDF is not attached: Press the [Ok] key.

Océ 3122 Copy

Océ 3121 – Copying Manual – English
1
PREFACE
Thank you for purchasing the Océ 3121 Series. This manual describes the Océ 3121 Series, their
functions, and their method of use. It also describes the various precautions to be observed in order to
ensure safe operation. Please read this manual thoroughly before operating the Océ 3121 Series in order
to familiarise yourself with its capabilities, and to make the most of its many functions. After reading this
manual, store it in a safe place for future reference.
CAUTION:
In this manual, CAUTION MESSAGES with this symbol indicate that neglecting the suggested
procedure or practice could result in personal injury.
NOTICE:
Considerable effort has been made to ensure that this manual is free of inaccuracies and omissions.
However, as we are constantly improving our products, some of the data contained herein may not
exactly reflect the current model of the particular product with which this manual has been included. If
you have a need for an exact specification, please contact Océ 3121 for the current specification.
This apparatus complies with the requirements of Directive 76/889/EEC, 87/308/EEC and European Standard EN 55014.
Cet appareil est conforme aux Directives 76/889/CEE et 87/308/CEE, ainsi qu’à la Norme Européenne EN 55014.
Dieses Gerät entspricht den Vorschriften der EG-Richtlinie 76/889/EWG, 87/308/EWG und der Europäischen Norm
EN 55014.
Dette apparat overholder bestemmelserne i EF-direktiverne 76/889/EEC, 87/308/EEC og Europæisk Standard EN 55014.
Denna apparat motsvarar kraven i EG-direktiv 76/889/EG och 87/308/EG samt Europeisk Standard EN 55014.
Tämä laite noudattaa EY-direktiivejä 76/889/EEC, 87/308/EEC sekä Euroopan Standardia EN 55014.
Dette apparat etterkommer kravene i EF direktiv 76/889/EEC, 87/308/EEC og europeisk standard EN 55014.
Deze apparatuur voldoet aan de gestelde richtlijnen 76/889/EEC, 87/308/EEC en aan de europese norm EN 55014.
Questo apparecchio è conforme alle direttive CEE/76/889, CEE/87/308 e alla normativa Europea EN 55014.
Este aparato cumple los requisitos de las directivas 76/889/CEE, 87/308/CEE y la Norma Europea EN 55014. Se han
incorporado filtros de línea para la eliminación de interferencias, según las especificaciones requeridas.
Este aparelho está de acordo com os requisitos da Directiva 76/889/EEC, 87/308/EEC e Standard Europeu EN 55014.
Η συσκευη´αυτη´συµφωνει´µε τις απαιτη´σεις των οδηγιω´ν 76/889/EEC, 87/308/EEC και τα Ευρωπαικα´Standard
EN 55014.
Aparat ustreza zahtevam navodil 76/889/EGS, 87/308/EGS in evropskemu standardu EN 55014.
A berendezés megfelel a 76/889/EEC, a 87/308/EEC és az EN 55014 szabványok elo˝írásainak.
Niniejsze urza˛dzenie spelnia wymagania zalecen´ 76/889/EEC, 87/308/EEC i normy europejskiej EN 55014.
Zarˇízení vyhovuje pozˇadavku˚m prˇedpisu˚ 76/889/EEC, 87/308/EEC a evropské normeˇ EN 55014.
Seade vastab EÜ normidele 76/889 EEC, 87/308 EEC ja Euroopa Standardile EN 55014.
Iekârta atbilst Eiropas Savienìbas direktìvu 76/889/EEC, 87/308/EEC un Eiropas standarta EN 55014 prasìbâm.
S
ˇis aparatas atitinka direktyvu˛ 76/889/EEC ir 87/308/EEC reikalavimus ir Europos standartus EN 55014.
Ètot apparat sootvetstvuet trebovaniqm direktiv 76/889/EEC, 87/308/EEC i Evropejskogo standarta
EN 55014.
Copier I.8

Océ 3122
Addendum Copy
Addendum Océ 3122

Océ 3122 Copy
Copying Manual
This document provides information which is new or has changed compared
with the Océ 3121 manual.
Common remarks
■The Fax Monitor key is always displayed in the Basic Features screen for
copying.
■When using the Stack Bypass, press the [Paper Select] key and then the
[Stack Bypass] key.
■The Film Projector is not available with the Océ 3122.
Page 3-27, Notice and 3-29, step 3: To cancel [Number of Output PGS] and
change to [Copy Ratio(s)], cancel the Multi-page Enlarge mode using the
Reset key and then change the specification.
Page 3-35, Memo: If the ADF or RDF is used and there are an odd number of
originals, the back of the last page is left blank. (The machine’s counter does
not count the blank page as a copy).
Page 3-37, step 4 and page 4-11, step 3: If you place your original on the
platen glass the following messages appear on the touch panel display:
“Copying the 2nd side...”
Place the 2nd original and press the Start key again.
“Copying the 1st side...”
Page 3-45, Memo in step 2:
■You can staple copies manually after they have been sorted, by using the
Manual Staple Mode.
■If you are going to perform manual stapling for sorted copies of originals
placed on the platen glass, before copying turn Face Down Output “Off” and
then start copying from the last page.
Page 4-19, Memo in step 3: The image will shift in the exact opposite
direction of the selected arrow.
Page 4-36, step 3:
■When the RDF is attached: Select either [2 on 1], [4 on 1] or [2 on
1/Two-sided], then press the [Ok] key.

Addendum Océ 3122
Notice: Only [2 on 1] can be selected when the originals are placed
horizontally.
■When RDF is not attached: Press the [Ok] key.

Océ 3122 Copy

Océ 3121 – Copying Manual – English
2
Manuals Provided with the Océ 3121 Series
We have prepared the following manuals so that you can make full use of the Océ 3121 Series
functions. The Copying Manual and Reference Manual (English versions) are packed together with all
of the main units in this product series. When other functions such as FAX functions are provided as
part of the standard specification, the function related manual (English versions) for the respective
function also is packed together with the main units. When FAX functions or printer functions are added
on later, the required function related manual is also packed together with the following boards
(optional). We recommend using these function related manuals in combination with the Reference
Manual.
Operator’s Manual
Main Unit
and Options
Reference
Manual Copying Manual Facsimile Manual PostScript/PCL Operator’s
Manual
PCL
Operator’s
Manual
Océ 3121 Yes Yes
Option
G3 FAX
Board-C1 Yes
Multi-PDL Printer
Board-B1 Yes
Printer
Board-P3 Yes

Océ 3121 – Copying Manual – English
3
Differences between Copying Manual and
Reference Manual
The Océ 3121 Series can be expanded to support non-copy functions such as, FAX and printer
functions. Accordingly, you are provided with a Reference Manual, Copying Manual, and a Facsimile
Manual.
Reference Manual: Describes operations common to all machines such as how to turn the
power ON, how to inspect and maintain machines, and how to handle
and set common functions.
Function related manual: Describes how to handle each of the functions such as copy and FAX
functions.
Descriptions of copy functions are distributed between the Reference Manual and Copying Manual as
follows. We recommend that you use these manuals according to your particular needs. At the back of
this Copying Manual, you will also find indexes that list the combined functions of the Reference
Manual and Copying Manual.
Reference Manual
Cautions for ensuring safe use of the machine ...................................................................(Chapter 1)
Names, functions and specifications of parts of copier and options....................................(Chapter 1)
How to turn the power ON and OFF ....................................................................................(Chapter 2)
Clearing paper jams..............................................................................................................(Chapter 5)
Loading paper (paper drawer, stack bypass) and adding toner ..........................................(Chapter 5)
Cleaning parts when copies appear dirty .............................................................................(Chapter 5)
How to set common specifications to each of the following functions.................................(Chapter 3)
·Settings on the display when power is turned ON
·Settings on display set by Initial Function
·Setting Automatic Exposure Adjustment
·Setting the Audible Tones (Entry tone, Error tone, Job completed tone)
·Setting whether or not each drawer is subject to Auto Drawer Switching function
·Setting paper size and icon for special cassettes
·Setting envelope cassettes
·Setting display of the Paper Selection display for the stack bypass
·Setting TRAY functions
·Setting the printing order in copy, FAX and printer operations
·Setting the system setting password
·Setting Dept. ID management
·Returning the Custom Common Settings to their defaults
·Setting the Auto Clear Time and Auto Sleep Time
Copying Manual
Parts and their functions when using the copy functions of the machine ...........................(Chapter 1)
How to place originals ..........................................................................................................(Chapter 2)
How to use the guide function ..............................................................................................(Chapter 2)
How to make copies in the Basic Features and Special Features modes .................(Chapters 3 to 6)
How to make copies using options.......................................................................................(Chapter 7)
How to set Custom Copy Settings to each of the following functions .................................(Chapter 8)
·Setting Automatic Sort ON/OFF
·Setting Reversal and Output of Copied Sheets ON/OFF
·Setting Display of Projector Key ON/OFF
·Setting Photo Mode ON/OFF
·Setting Standard Keys
·Restoring Settings to Initial Settings
·Changing the Current Standard Settings

Océ 3121 – Copying Manual – English
4
Contents
■Preface........................................................................................................................ 1
Manuals Provided with the Océ 3121 Series .....................................................................2
Differences between Copying Manual and Reference Manual ..........................................3
Contents ..............................................................................................................................4
How This Manual is Organised...........................................................................................8
Illustrated Function Summary .............................................................................................9
How to Use This Manual ..................................................................................................26
Chapter 1 Before You Start Using Copy Functions
■Parts and Their Functions .................................................................................... 1-2
·Control Panel......................................................................................................... 1-2
·Touch Panel Display............................................................................................. 1-3
·Basic Features Screen..................................................................................... 1-3
·Special Features Screen.................................................................................. 1-4
·Additional Function Screen.............................................................................. 1-6
■Keying Operations................................................................................................. 1-7
·Using the Control Panel to Perform Settings........................................................ 1-7
·Using the Touch Panel Display to Perform Settings.......................................... 1-11
Chapter 2 Basic Copying
■Flow of Copy Operations...................................................................................... 2-2
·Auto Drawer Switching.......................................................................................... 2-5
·Auto Clear Function .............................................................................................. 2-5
·Sleep Function ...................................................................................................... 2-5
·Auto Sleep Function.............................................................................................. 2-6
·Paper Supply Indicator.......................................................................................... 2-6
·Guide Function...................................................................................................... 2-7
■Inserting the Control Card.................................................................................... 2-8
·Operations before Using Copy Functions............................................................. 2-8
·Operations after Using Copy Functions................................................................ 2-9
■Entering the Dept. ID and Password ................................................................. 2-10
·Operations after Turning Power ON................................................................... 2-10
·Operations after Using Copy Functions.............................................................. 2-11
■Placing Originals.................................................................................................. 2-12
·Orientation of Originals ....................................................................................... 2-12
·Placing an Original on the Platen Glass............................................................. 2-13
·Placing Originals in the ADF............................................................................... 2-14
·How Originals Feed Through the ADF .......................................................... 2-15
·Placing Originals in the RDF............................................................................... 2-16
·How Originals Feed Through the RDF
(when making copies of one side of the original).......................................... 2-18
·How Originals Feed Through the RDF
(when making copies of two sides of the original)........................................ 2-19
■Entering the Copy Quantity (making a specific number of copies)............... 2-20
·Entering the Copy Quantity................................................................................. 2-20
·Changing the Copy Quantity............................................................................... 2-21
■Interrupting the Current Copy Job to Make Priority Copies
(Interrupt Mode).................................................................................................... 2-22

Océ 3121 – Copying Manual – English
5
Chapter 3 Making Copies Using the Basic Features
■Selecting the Copy Paper Size (PAPER SELECT).............................................. 3-2
·Auto Paper Selection ............................................................................................ 3-2
·Manual Paper Selection........................................................................................ 3-4
·Using the Stack Bypass........................................................................................ 3-5
■Adjusting Exposure and Image Quality............................................................... 3-8
·Adjusting Exposure (LIGHT, DARK)..................................................................... 3-8
·Selecting Image Quality (TEXT, TEXT/PHOTO, PHOTO)................................... 3-9
·Automatic Adjustment of Exposure and Image Quality (A)................................ 3-11
■Enlarging/Reducing Originals from One Standard Paper Size to Another
(R, 1:1, E).............................................................................................................. 3-12
■Reducing/Enlarging Originals to the Desired Size (ZOOM MODE) ................ 3-14
·Reducing Originals at a Desired Copy Ratio (ZOOM) ....................................... 3-14
·Automatically Setting the Copy Ratio Based on the Original and Copy
Paper Sizes (AUTO ZOOM)................................................................................ 3-16
·Slightly Reducing Images to Prevent the Original Periphery from Being Cut
(ENTIRE IMAGE)................................................................................................. 3-19
·Calculating the Copy Ratio Based on the Original and Copy Paper Sizes
(ZOOM PROGRAM)............................................................................................ 3-20
·Enlarging/Reducing Originals at Copy Ratios Set Independently for X and Y
Axes (XY ZOOM)................................................................................................. 3-23
·Manually Specifying the Copy Ratio.............................................................. 3-24
·Automatically Specifying the Copy Ratio....................................................... 3-25
·Reducing/Enlarging Originals to Copy Paper Sizes Larger than A3
(MULTI-PG ENLARGE)....................................................................................... 3-27
·Copy Ratio Specification and Required Paper Sizes and Quantities ........... 3-28
·Specifying the Copy Ratio by % (COPY RATIO (S)).................................... 3-29
·Specifying the Copy Ratio by Number of Output Pages
(NUMBER OF OUTPUT PGS)...................................................................... 3-31
■Copying Two-sided Originals, Copying onto Both Sides of Copy Paper
(TWO-SIDED) ........................................................................................................ 3-34
·Making Two-sided Copies from One-sided Originals (1 ➝2-SIDED)................ 3-35
·Making Two-sided Copies from Two-sided Originals (2 ➝2-SIDED)................ 3-38
·Making One-sided Copies from Two-sided Originals (2 ➝1-SIDED)................ 3-40
·Making Two-sided Copies from Facing Pages in a Book in One Step
(BOOK ➝2-SIDED)............................................................................................ 3-42
■Sorting Copies (SORTER)................................................................................... 3-44
Chapter 4 Special Features
■Special Feature Modes.......................................................................................... 4-2
■Calling up the Special Features Screen.............................................................. 4-3
■Making Copies of Facing Pages in a Book onto Two Separate Copy
Sheets in One Step (TWO-PAGE SEPARATION)................................................ 4-4
■Making Copies with Sheets of Paper Interleaved between Transparencies
(TRANSP. INTERLVING)........................................................................................ 4-6
■Superimposing Two Original Images onto a Single Copy Sheet
(OVERLAY).............................................................................................................. 4-9
·Superimposing Two Originals (SHEET OVERLAY) ........................................... 4-10
·Superimposing Facing Pages in a Book (BOOK OVERLAY) ............................ 4-12
■Feeding Different-size Originals Together in the Feeder
(DIF. SIZE ORIGINAL) .......................................................................................... 4-14

Océ 3121 – Copying Manual – English
6
■Scanning Thin Sheet Originals (THIN SHEET ORIGINAL)............................... 4-16
■Making Copies with Original Images Shifted (SHIFT)...................................... 4-18
·Making Copies with Original Images Shifted to the Center or Corner............... 4-18
·Making Copies with Original Images Shifted Using the Number Keys.............. 4-19
■Making Copies with Margins (MARGIN)............................................................ 4-22
·Making Copies with Margins on Left or Right..................................................... 4-22
·Making Copies with Margins on Top or Bottom ................................................. 4-24
■Erasing Shadows from Copies (FRAME ERASE)............................................. 4-26
·Erasing Shadows Around the Original Image on Copies
(ORIGINAL FRAME ERASE).............................................................................. 4-27
·Erasing Shadows from the Edge of Copies (SHEET FRAME ERASE)............. 4-29
·Erasing Shadows from the Center Line or Edge of Copies
(BOOK FRAME ERASE) .................................................................................... 4-30
·Erasing Binding Holes on Copies (BINDING ERASE) ...................................... 4-31
■Reducing Two or Four Originals to Fit on a Single Copy Sheet
(IMAGE COMB.)................................................................................................. 4-33
■Dividing an Original into Equal Sections and Copying Each Section on
a Separate Copy Sheet (IMAGE SEPARATION)................................................ 4-38
Chapter 5 Making Copies Using Image Processing Features
■Image Processing Modes...................................................................................... 5-2
■Image Processing Designated Areas (AREA DESIG.) ....................................... 5-3
·Designating Areas................................................................................................. 5-4
·Clearing Designated Areas (CLEAR AREA)......................................................... 5-6
■Making Copies Using Image Processing Features (IMAGE CREATION)......... 5-8
·Inverting Original Images (NEGA/POSI)............................................................... 5-8
·Making Copies with Original Images Repeated in the Vertical Direction
(IMAGE REPEAT)................................................................................................. 5-9
·Making Copies with Original Images Flipped around the Horizontal Axis
(MIRROR IMAGE)............................................................................................... 5-12
·Making Copies with Original Images Slanted (SLANTED IMAGE).................... 5-15
■Making Sharp Contrast Copies (SHARPNESS) ................................................ 5-17
Chapter 6 Recalling and Storing Modes (Two Special Features)
■Modes in which Copy Jobs can be Called up.................................................... 6-2
■Storing Often Used Copy Settings in Memory (MODE MEMORY) ................... 6-3
·Storing Copy Settings for a Copy Job.................................................................. 6-3
·Storing a Memory Key Name................................................................................ 6-6
·Erasing a Copy Job............................................................................................... 6-8
·Recalling a Copy Job.......................................................................................... 6-10
■Recalling the Previous Copy Job (RECALL) .................................................... 6-11

Océ 3121 – Copying Manual – English
7
Chapter 7 Making Copies Using the Optional Film Projector
■Names of Parts on Film Projector........................................................................ 7-2
■How to Setup and Disconnect the Film Projector.............................................. 7-3
·How to Set up the Film Projector.......................................................................... 7-3
·How to Disconnect the Film Projector .................................................................. 7-4
■Making Copies from Photographic Film (PROJECTOR).................................... 7-6
·Making Copies from 35 mm Negative Film .......................................................... 7-7
·Making Copies from 35 mm Positive Film.......................................................... 7-13
·Making Copies from 4 x 5 Negative Film ........................................................... 7-18
·Making Copies from 4 x 5 Positive Film............................................................. 7-23
·Cautions when Using the Film Projector ............................................................ 7-28
·Main Specifications ............................................................................................. 7-28
Chapter 8 Custom Settings
■What are “Additional Functions”?....................................................................... 8-2
·Calling up the Custom Copy Settings Screen...................................................... 8-2
·Custom Copy Settings .......................................................................................... 8-4
■Setting Automatic Sort ON/OFF (AUTO SORT).................................................. 8-5
■Setting Reversal and Output of Copied Sheets ON/OFF
(FACE DOWN OUTPUT)......................................................................................... 8-6
■Setting Display of Projector Key ON/OFF (PROJECTOR)................................. 8-7
■Setting Photo Mode ON/OFF (PHOTO MODE).................................................... 8-8
■Setting Standard Keys (STANDARD KEY1/KEY2 SETTING)........................... 8-10
■Restoring Settings to Initial Settings (INITIALISE CUSTOM SETTINGS)....... 8-11
■Changing the Current Standard Settings (STANDARD SETTINGS)............... 8-12
·Storing the Standard Settings............................................................................. 8-13
·Initialising the Standard Settings......................................................................... 8-14
Chapter 9 Troubleshooting
■Self-diagnostic (Error) Displays........................................................................... 9-2
■Service Call Message ............................................................................................ 9-4
Chapter 10 Appendix
■Main Specifications.............................................................................................. 10-2
■Index...................................................................................................................... 10-4

Océ 3121 – Copying Manual – English
8
How This Manual is Organised
Chapter 1 Before You Start Using Copy Functions
This chapter describes items you should understand and be familiar
with before using the machine, such as names and functions of parts
on the control panel, how to use the touch panel display, and
meanings of items that appear in the touch panel display.
Chapter 2 Basic Copying
This chapter describes the steps necessary to perform basic copying
with the Océ 3121 Series, including simple ways of making copies,
entering the copy quantity, how to use the Interrupt mode, and how to
place originals.
Chapter 3 Basic Features
This chapter describes the modes that can be selected from the Basic
Features screen in the touch panel display.
Chapter 4 Special Features
This chapter describes the modes that can be selected from the
Special Features screen in the touch panel display.
Chapter 5 Making Copies Using Image Processing
Features
This chapter describes image processing (Area Designation,
Sharpness, Image Creation) that can be set in the Special Features
screen.
Chapter 6 Recalling and Storing Modes
(Two Special Features)
This chapter describes the ”Mode Memory” and ”Recall” features that
can be selected in the Special Features screen.
Chapter 7 Making Copies Using the Film Projector
This chapter describes the ”Projector” mode that can be selected from
the Special Features screen. Attaching the optional film projector on
the machine allows you to make copies from photographic film.
Chapter 8 Custom Settings
This chapter describes how you can change or adjust the initial
settings (defaults) for the various functions described in this chapter to
meet your specific copying needs.
Chapter 9 Troubleshooting
This chapter describes the procedures to be followed when a self-
diagnostic message or service call message appears in the touch
panel display.
Chapter 10 Appendix
This chapter describes machine specifications and gives an index of
this manual.
Parts and Their Functions
Keying Operations
Flow of Copy Operations
Inserting the Control Card
Entering the Dept. ID and Password
Placing Originals
Entering the Copy Quantity (making a specific number of copies)
Interrupting the Current Copy Job to Make Priority Copies (Interrupt
Mode)
Selecting the Copy Paper Size (PAPER SELECT)
Adjusting Exposure and Image Quality
Enlarging/Reducing Originals from One Standard Paper Size to Another
(R, 1:1, E)
Reducing/Enlarging Originals to the Desired Size (ZOOM MODE)
Copying Two-sided Originals, Copying onto Both Sides of Copy Paper
(TWO-SIDED)
Sorting Copies (SORTER)
Special Feature Modes
Calling up the Special Features Screen
Making Copies of Facing Pages in a Book onto Two Separate Copy
Sheets in One Step (TWO-PAGE SEPARATION)
Making Copies with Sheets of Paper Interleaved between
Transparencies (TRANSP. INTERLVING)
Superimposing Two Original Images onto a Single Copy Sheet
(OVERLAY)
Feeding Different-size Originals Together in the Feeder (DIF. SIZE
ORIGINAL)
Scanning Thin Sheet Originals (THIN SHEET ORIGINALS)
Making Copies with Original Images Shifted (SHIFT)
Making Copies with Margins (MARGIN)
Erasing Shadows from Copies (FRAME ERASE)
Reducing Two or Four Originals to Fit on a Single Copy Sheet (IMAGE
COMB.)
Dividing an Original Into Equal Sections and Copying Each Section on a
Separate Copy Sheet (IMAGE SEPARATION)
Image Processing Modes
Image Processing Designated Areas (AREA DESIG.)
Making Copies Using Image Processing Features (IMAGE CREATION)
Making Sharp Contrast Copies (SHARPNESS)
Modes in which Copy Jobs can be Called up
Storing Often Used Copy Settings in Memory (MODE MEMORY)
Recalling the Previous Copy Job (RECALL)
Names of Parts on Film Projector
How to Setup and Disconnect the Film Projector
Making Copies from Photographic Film (PROJECTOR)
Cautions when Using the Optional Film Projector
Main Specifications
What are ”Additional Functions”?
Setting Automatic Sort ON/OFF (AUTO SORT)
Setting Reversal and Output Copies Sheets ON/OFF (FACE DOWN
OUTPUT)
Setting Display of Projector Key ON/OFF (PROJECTOR)
Setting Photo Mode ON/OFF (PHOTO MODE)
Setting Standard Keys (STANDARD KEY1/KEY2 SETTING)
Restoring Settings to Initial Settings (INITIALISE CUSTOM SETTINGS)
Changing the Current Standard Settings (STANDARD SETTINGS)
Self-diagnostic (Error) Displays
Service Call Message
Main Specifications
Index

Océ 3121 – Copying Manual – English
9
Illustrated Function Summary
[PAPER SELECT]
(See p. 3-2.)
The machine automatically
selects the right paper size
based on the size of the original
and the selected copy ratio.
A5 original Copy to A4
Example:
If you want to make
an A5 copy of an
A4 original,
designate the size
manually.
[ ] (LIGHT)
[] (DARK)
(See p. 3-8.)
Adjusts the copy exposure to
match the contrast of the
original.
Original Light Dark
[ ] (TEXT)
[] (TEXT/PHOTO)
[] (PHOTO)
(See p. 3-9.)
Adjusts the image quality to
match the type of original.
Text Text/Photo Photo
[A] (AUTO)
(See p. 3-11.)
The machine automatically
adjusts the image quality to the
most appropriate level.
Specifications are also set so
that the exposure and image
quality are automatically
adjusted.
Original Copy
1
2
3
4
5
6
7
8
9
10

Océ 3121 – Copying Manual – English
10
[R]
(See p. 3-12.)
Makes reduced size copies of
standard-size originals onto
standard-size paper.
A4R original A5R copy
[1:1]
(See p. 3-12.)
Makes copies the same size as
the original.
A4R original A4R copy
[E]
(See p. 3-12.)
Makes enlarged size copies of
standard-size originals onto
standard-size paper.
A5R original A4R copy

Océ 3121 – Copying Manual – English
11
[ZOOM]
[–] (ZOOM)
[+]
(See p. 3-14.)
Makes reduced or enlarged
copies at any copy ratio in 1%
increments.
Original Copy
[AUTO]
(See p. 3-16.)
The machine automatically
selects the appropriate copy
ratio based on the size of the
original and the selected copy
paper.
Enlargement Reduction
[ENTIRE IMAGE]
(See p. 3-19.)
When copying an original where
the image fills the page, parts of
the image may be cut off on
copies. Using the Entire Image
mode, the image is slightly
reduced before copying so that
the entire original image is
reproduced on the copy.
Original Copy
1
2
3
4
5
6
7
8
9
10

Océ 3121 – Copying Manual – English
12
[ZOOM PROGRAM]
(See p. 3-20.)
You can designate the original
size (size of original image or
original) and copy size (size of
copied image or paper) in mm
when making copies.
[XY ZOOM]
(See p. 3-23.)
You can designate different copy
ratios (%) for each of the X and
Y directions when making
copies.
[MULTI-PG ENLARGE]
(See p. 3-27.)
The machine automatically
calculates how many sheets the
original is to be copied on based
on the enlarged copy size. If you
cut and paste the output sheets
together, you can make copies
larger than A3 in size.
Original Copy
X=100 mm X=150 mm
ZOOM
(X and Y axes are reproduced at the same size)
Original Copy
X=100 mm X=80 mm
ZOOM
(X and Y axes are reproduced at different sizes)
Y=120 mm Y=140 mm
Original Copy
X=120%
XY ZOOM
(X and Y axes are
reproduced at
manually set sizes)
Y=80%
Original Copy
A4 A4R
XY ZOOM
(X and Y axes are reproduced at manually set sizes)
A4R
drawer
selected.
Original Copy Copies cut and
pasted together.