Octane Fitness PRO 310 User manual
ii
This product is intended for commercial use.
IMPORTANT SAFETY INSTRUCTIONS
Please Read and Save These Instructions
WARNING!Anyone using this product should consult a physician before starting an exercise program. This is
especially important for persons over 35 or persons with pre-existing health conditions. If at any time during a
workout an exerciser experiences chest pains, nausea, dizziness, or shortness of breath, the exerciser should stop
exercising immediately and consult a physician before starting again.
Have all club, personal training, and sales staff members review this Operations Manual before operating this
elliptical cross trainer. Also, make this Operations Manual accessible to all exercisers.
WARNING!When using an electrical product, basic precautions should always be followed.
To reduce the risk of burns, fire, electrical shock or injury to people:
Do not modify the
product in any way.
Do not remove the plastic shrouds from the machine. Service should be performed only by an authorized
Octane Fitness service representative. Moving parts contained under the shrouds can be extremely
dangerous when not covered.
Never operate this elliptical cross trainer if it has a damaged cord or plug, if it is not working properly, if it
has been dropped or damaged, or dropped in water. Return the cross trainer to your local dealer or Octane
Fitness for examination and repair.
Never operate this elliptical cross trainer with the air openings blocked. Keep the air opening free of lint,
hair, and the like.
Do not use outdoors.
Do not operate this elliptical cross trainer where aerosol (spray) products are being used or where oxygen
is being administered.
Do not route power cables (such as the power cable for an optional attached LCD screen) through the
interior of the machine or the upright tube.
Do not mount an LCD screen weighing more than 12.5 lbs. (5.7 kg) on the optional LCD mounting arm.
Never place the power cord under carpeting or place any object on top of the power cord which may pinch
and/or damage it.
Octane Fitness elliptical cross trainer.
Octane Fitness elliptical cross trainer before moving it.
SAVE THESE INSTRUCTIONS
iii
OTHER IMPORTANT SAFETY PRECAUTIONS
its furthest back position.
If you have more than one unit, position them so that there are at least 24 inches (60 cm) between units.
while the foot pedals are still moving.
Octane Fitness elliptical cross trainer.
a workout an exerciser feels any chest pain, nausea, dizziness, or abnormal symptoms, stop the
workout immediately and consult a physician.
Refer to the Cleaning and
Maintenance section of this manual for more information about the care of your Octane cross trainer.
Octane Fitness Customer Service for assistance.
(65in x 29in x 61in)
Input Rating 100-240V~0.7A
Output Rating +9V 2.0A
Output Ripple 90mV
Output Current 2.0A Max
Mark
This equipment complies where applicable with:
(RoHS) Directive
appliances - Safety
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
iv
HEART RATE FEATURE SAFETY GUIDELINES
Octane Fitness™ Intelligence, read and follow these instructions:
Contact Heart Rate Grips
short.
grasp each contact heart rate grip so the contact sensor portion of the grip rests
Wireless Chest Strap
Do not allow users to use the chest strap if they have a cardiac pacemaker or are taking
prescription medication. Medication or electrical impulses from the cardiac pacemaker can cause
inaccurate heart rate readings.
and this could void the warranty.
could result. In a commercial setting, space the products at least 24” apart. This will prevent cross-talk,
where the chest strap signal from a user on one machine can be received and displayed on the console of
another machine.
motors, radios, and high voltage power lines can affect the transmitter’s performance. These items can
interfere with the heart rate signal that is being transmitted to the receiver, possibly affecting the heart
rate readings that appear on the electronic console.
small amount of water. The electrodes are the ribbed portion on the side of the transmitter that sits against
your skin.
electrodes may cause inaccurate readings. The electrodes are the ribbed portion on the side of the
transmitter that sits against your skin. If the battery has failed, a new chest strap must be purchased.
Some individuals are unable to use the heart rate feature because they do not have the proper body chemistry
to provide accurate readings. If you experience difficulties in using the contact heart rate grips or a wireless
WARNING!The heart rate monitoring features of this product are for information only and are not to be used
as a measure of heart functioning or heart health. In a heart rate controlled program, the exerciser can use the
Level controls to reduce the resistance level at any time. Each exerciser is responsible for monitoring how
he or she feels and adjusting the level of effort accordingly. If at any time during exercise a user experience
chest pains, nausea, dizziness, or shortness of breath, he or she should stop exercising immediately and consult
a physician before starting again.
v
PRO310 PRODUCT LABELS
Console Serial Number
(on lower edge)
Base Serial Number
S/N:R05680027943- 01
Max User Weight: 300lbs/136kg
RoHS
Compliant
9V 2.0A Class SC
Covered by one or more of U.S. Patents Nos. 6248044, 7270626, 7244218,
D547159,5938570, 6409635, and other patents pending. Made in Taiwan
7601 Northland Drive North, Suite 100
Brooklyn Park, MN 55428 USA
OCTANE FITNESS, LLC
Input Rating 100-240V~0.7A
vi
TABLE OF CONTENTS
Getting Started............................................................................................................................... 1
•UserSet-UpFunctions........................................................................................................ 1
•Cleaning and Maintenance of the PRO310 Series Elliptical ..................................... 2
•Troubleshooting&FrequentlyAskedQuestions........................................................... 2
•WarrantyInformation......................................................................................................... 2
Electronics................................................................................................................................ 3
•PRO310ConsoleandKeypad ............................................................................................ 3
•Keypad Buttons.................................................................................................................... 4
•Console Windows ............................................................................................................... 6
PRO310 Programs .......................................................................................................................... 8
•How Does Workload Resistance (Level) Work?........................................................... 8
•PRO310Program Reference .............................................................................................. 9
•PRO310Settings—Value Ranges ................................................................................... 11
PRO310 Product Features........................................................................................................... 12
•HeartRateMonitoringandHeartLogic Intelligence.................................................. 12
•MultiGripHandlebars....................................................................................................... 13
1
GETTING STARTED
challenging yourself with a variety of pre-programmed workouts, managed by sophisticated electronics that keep
you interested and motivated. Getting started is easy—just step on and start pedaling. Follow the prompts to
USERSET-UPFUNCTIONSworkout environment. become the new standard and do not need to be reset for each use.
Warm-UpPause Turning this function to “OFF” lengthens the period of time before a program automatically
which is the appropriate setting for a typical user. The “OFF” setting is primarily used during
product demonstrations.
Clock
Direction Movement
Management
(MOM) mode disables the console buttons and increases the resistance in the movement of the pedals
so that the pedals do not move as easily. This control feature may discourage children from
experimenting with the machine.
until you hear the beep.
CAUTION! MOM mode is a feature provided to reduce the likelihood that children
canpedaltheellipticalcross-trainer.Thisfeaturedoesnotlockthemachine;thepedalsstillmoveandthepotentialforinjurystillexists.Itistheresponsibilityoftheuser to supervise children and keep them off the elliptical cross trainer to minimize
the likelihood of injury.
Units Beep 30:30 Rest
Minutes minutes.
Brightness and 8. A higher number represents more light. The factory default setting is 8.
Exit and become the new standard settings for your machine. They may be changed at any time by
repeating these set-up procedures.
2
Cleaning and Maintenance of the PRO310 Series Elliptical
WARNING! This machine contains moving parts. Take caution when trying to locate and fix any problem with
the machine.
sweat to keep the machine clean. Do not use bleach on the console as it will damage the surface.
after useOctane Fitness customer service specialist,
Troubleshooting&FrequentlyAskedQuestionsWarranty Information
warranted to be free of all defects in material and workmanship for a specific period of
time from original date of purchase. your information packet for full terms and details of warranty coverage.
3
Enter +
-
+
-
+
- -
+ +
-
ArmBlaster GluteKicker
Press to Fuel Your Workout
Workout Boosters
ELECTRONICS
PRO310 Console and Keypad
4
motivated during your workout. Check out the program descriptions found later in this manual to choose the
workout that is just right for you.
Getting started is easy—just hop on and start pedaling. DedicatedLogic™programming gives you the ultimate in
ease of use and total flexibility for programming your console. This allows you to modify your workout once you’ve
only one function. This makes it easy to understand how each key works.
Keypad Buttons
QuickStartThe easiest way for you to start your workout is to simply push the Quick Start button,
setting the machine in a manual program at resistance level one. The calories readout
will be based on a 150 lb. (68 kg) user, age 40. Once you have selected Quick Start, you
can program any item in any order.
Cool Down It is always a good idea to perform a cool-down at the end of your routine. This will
help transition your body from an aggressive workout to its normal pace. The time and
intensity of the cool-down is automatically customized to your workout duration and
resistance level. The time window will change to a countdown timer to tell you how
long the cool-down will last.
If you have set a time for your workout, the cool-down will automatically start when
time has expired. If you decide to end your workout early or have not set a time
goal, simply push the Cool Down button to activate the custom cool-down. At the
completion of your cool-down a workout summary will be displayed.
Pause Clear made at any time while the machine is in pause mode. To restart a paused workout,
push any key or just begin pedaling. If you stop pedaling during a workout, the unit
little power in this mode. To “wake” your elliptical, simply press any button or begin
pedaling.
Up and Down Keys
Time to increase or decrease the time of your workout, in 1 minute
increments. The standard workout time is 30:00. The maximum time is 99:00.
Program programs, the matrix window prompts you to enter new program values as needed.
Note: The Program (+) or (–) keys are also used to activate the MOM (MOvement
Management) motion control feature of the Octane Fitness elliptical.
Level to increase or decrease the resistance level of the machine. There
are 20 levels of resistance for preset resistance programs and the 30:30 fitness number
program. For heart rate controlled programs, the Level button increases your target heart
rate.
5
Age to enter the age to be usedprogram calculates a recommended target heart rate based on the formula (220 – age) =
theoretical maximum heart rate (TMHR). That number is then multiplied by the program
intensity value to determine your target heart rate(s).
Weight kilograms (metric)Enter Selects any of the changed values or items from the above keys. Also, pressing the
display modes.
Workout Boosters
ArmBlaster workout to integrate cardio sessions with strength sessions. The cardio session follows
muscle-building, 10-repetition set as you transfer the workload from your lower body to
button a second time.
Tip: If your PRO310 is equipped with the optional CROSS CiRCUIT+ stationary foot
platforms, step onto the platforms during your ArmBlaster sessions for an even more
intense upper-body challenge.
X-Modeyour elliptical cross trainer offers. This great motivational tool keeps your workout fresh
combinations of eight different challenges:
FastSquatReverseLean Back Grab the stationary handlebars and lean slightly backwards, changing the muscle focus on
Lower Body OnlyPush-ArmsFocus on pushing with your arms to work your chest and triceps.
Pull-ArmsFocus on pulling with your arms to work your biceps and lats.
Slow Slow down to 30-40rpm to allow yourself to recover.
keys on the keypad or the right handlebar. a second time.
GluteKicker thighs. It uses four prompts: Reverse, Squat, Fast, and Lean Back. GluteKicker sessions
last for one minute, with a one-minute recovery period. During the GluteKicker session,
keys on the keypad or the
right handlebar. Deactivate GluteKicker by pressing the button a second time.
6
Console Windows
Matrix Display important information, shows the program profile
during the workout and highlights upcoming
intervals and resistance changes. Watch the
matrix display as you set up and progress through
your workout—it will guide you, motivate you,
and reward you with summary information at the
end of your session.
Changing Target Heart Rates: When you are
trying to reach a new target heart rate, the left
side of the matrix display shows an illustration
of the interval. The illustration blinks the interval
represents one minute. An arrow on the right
side of the display shows whether resistance
(and therefore your target heart rate) is increasing
or decreasing. When decreasing, if the machine
reaches resistance level 1 and your heart rate
has still not reached your target low, the display
the machine reaches the highest resistance level (20) and your heart rate has still not
Interval Duration: Once you have reached or
surpassed the new target heart rate, the matrix
display switches to a countdown timer, counting
down the length of the interval. The bottom row
of the matrix displays a horizontal bar graph
representing the current resistance level.
Upcoming columns blink
7
Time Displays workout time, counting up from 0:00. Time can be increased or decreased during
your workout. The maximum time that users can set is 99:00. When actual workout time is
Functions to learn how to switch from a “count up” to “count down” display.
Distance Displays an estimate of how far you have traveled. Distance can be shown in either miles
Note:
On the PRO310, 400 revolutions is approximately one mile; therefore, if you are pedaling at 50
rpm, you will “travel” approximately one mile in 8 minutes.
Speed Displays how fast you are going, in revolutions per minute (rpm).
Calories Displays an estimate of the total calories burned during the workout, based on the user’s
entered weight. If no specific weight is entered, calories are based on a 150 lb. (68 kg) user.
Cal/Hr Displays the number of calories that would be burned in one hour at the current resistance
level and speed.
Time-in-ZoneTracks and displays the amount of time spent in the proper heart rate training zone for the
when a heart rate is detected by the machine. Note: You must be wearing a wireless heart
rate transmitter or consistently grasping the contact heart rate sensor grips on the stationary
handlebars in order to get an accurate reading of Time-in-Zone.
Heart Rate Note: You must be wearing a wireless heart
rate transmitter or consistently grasping the contact heart rate sensor grips on the stationary
handlebars.
Heart Rate % Displays your current heart rate percentage (current heart rate / theoretical maximum heart
rate). Note: You must have entered your age and be wearing a wireless heart rate transmitter
or consistently grasping the contact heart rate sensor grips on the stationary handlebars in
order to get an accurate reading of Heart Rate %.
Target HR Displays the heart rate reading that the machine is adjusting resistance to achieve when
resistance level in response to your heart rate in order to achiever this target.
Level Displays the resistance level (1-20), where 1 is the lowest resistance level and 20 is the
highest.
8
PRO310 PROGRAMS
The PRO310 has 12 built-in programs to keep you motivated and challenged:
Goal programs: 350 Calories—750 Calories—10K—1/2 Marathon
increases each minute. At the end of the warm-up, you will be at your selected resistance value or target heart
How Does Workload Resistance (Level) Work?
Resistance Level The30-30) allow the user to select the resistance level for specific intervals.
resistance level is represented by rows
table below will help you understand and interpret the matrix display:
Resistance Levels LED Rows Lit Resistance Levels LED Rows Lit
1-2 1 11-12 6
3-4 2 13-14 7
5-6 3 15-16 8
7-8 4 17-18 9
9-10 5 19-20 10
Program Level The Random program and Goal programs using the ‘Hills’ profile let you select an
overall resistance level for the program. This level is the average resistance level
for the workout. The range of resistance levels during these workouts are plus (+)
or minus (-) 4 of the entered program level. That is, for program Level 5, minimum
resistance is Level 1 and maximum resistance is Level 9. During the workout, the
time.
Resistance in Heart
Rate Controlled
Programs enter the target heart rate level for program. If the target HR is reached during the
warm-up, the warm-up ends and the selected heart rate control program begins.
The resistance level during the heart rate controlled workout is controlled by the
machine, increasing or decreasing as necessary to keep your heart rate on target.
setting the resistance level and time for each program. Four programs—Manual, Custom Interval, Custom Heart
Rate Interval—provide great flexibility to program individual workouts to meet specific needs.
9
PRO310 PROGRAM REFERENCE
Press Program (+) or (–) and Enter to choose a program.
CLASSIC PROGRAMS
Programs & Standard Settings Description
Level (1) simulates walking or
shows laps completed.
Level (1) interval lasts one minute.
Intervals (3)
Interval 1 — Time (00:30)
Interval 1— Level (1)
Interval n— Time (00:30)
Interval n— Level (1)
Design a custom workout of up to 6 alternating intervals of
adjust interval resistance mid-workout.
Day (1) preset values for resistance level, time and a suggested
each day, building up your stamina and getting you ready
dayGOAL PROGRAMS
Programs & Standard Settings Description
GOAL!
350
Calories
350 Calories
or
350 Calories
GOAL!
350
Calories
Goal (350)
Weight (150 lbs./68 kg)
Level (1)
Get moving on a flat or ‘hilly’ course until you have
Note: To select “hills”, press any
10
PRO310 PROGRAM REFERENCE
Press Program (+) or (–) and Enter to choose a program.
GOAL!
750 Calories
750 Calories
or
750 Calories
GOAL!
750 Calories
Goal (350)
Weight (150 lbs./68 kg)
Level (1)
For an even greater challenge...work the course until you
interval resistance mid-workout. Complete this program
Note: To select “hills”, press any GOAL!
10K
10K
or GOAL!
10K
10K
Goal (6.2 mi./10K)
Level (1)
Complete a virtual 10K—a great way to train for an actual
event. Choose a flat course or take to the hills as gradual
resistance changes simulate variance in terrain, replicating
the challenges encountered when walking or running
outside. The distance readout counts down from 6.2 miles
(10 kilometers). resistance mid-workout.
Note: To select “hills”, press any GOAL!
1/2 Marathon
1/2 Mar at hon
or
Goal (13.1 mi./21K)
Level (1)
Get ready for the long run as you tackle the 1/2 marathon.
Choose the flat or ‘hilly’ course and watch the miles fall
away as the distance readout counts down from 13.1
miles (21 kilometers). resistance mid-workout.
Note: To select “hills”, press any PRO310 HEART RATE PROGRAMS
Programs & Standard Settings Description
Age (40)
Target Heart Rate (.65 *(220 - Age)
Maximize the percentage of calories burned from fat
versus carbohydrates with this controlled workout at 65%
heart rates mid-workout.
11
PRO310 SETTINGS—VALUE RANGES
Setting Standard Values* Minimum Value Maximum Value
Workout Time
Level
Age
Weight
Interval Time
Interval Level
How Many Intervals
Target Heart Rate
Calorie Goal
Distance Goal
Flat or Hills?
30:00
1
40
150 lbs. (68 kg)
00:30
1
3
350 or 750
6.2 miles (10K) or 13.1 Miles (21K)
Flat
1:00
1
15
70 lbs. (32 kg)
00:15
1
2
80
25
.25 miles (.4 km)
n/a
99:00
20
99
300 lbs. (181 kg)
99:00
20
6
(220 - Age)
2000
50 miles (80 km)
n/a
*Standard program values are used if no values are entered within 4 seconds of Message Center prompts.
PRO310 PROGRAM REFERENCE
Press Program (+) or (–) and Enter to choose a program.
Age (40)
Target Heart Rate (.80 * (220 - Age) workout at 80% of theoretical maximum heart rate (or
adjust interval target heart rates mid-workout.
Age (40)
Intervals (3)
Interval 1 — Time (00:30)
Interval 1 — Target Heart Rate (.75* (220 - Age))
Interval n— Time (00:30)
Interval n— Target Heart Rate (.75* (220 - Age) heart rates mid-workout.
High Interval Level (8)
This challenging program provides a simple test of fitness
level with 5 sets of 30-second sprint and recovery intervals.
For each set, the program monitors heart rate and calculates
the average minimum and average maximum heart rates
and the average number of beats the heart rate recovers
between sprint intervals. Heart rate recovery is a relative
more rapid heart rate recovery and therefore represents a
relatively better level of fitness.
*Standard program values are used if no values are entered within 4 seconds of Message Center prompts.
12
PRO310 PRODUCT FEATURES
workouts, including HeartLogic Intelligence and MultiGrip Handlebars. In addition, many of the standard
workout environment.
Heart Rate Monitoring and HeartLogic Intelligence
monitoring and control technologies that help you make the most
monitoring—just grasp the digital contact heart rate grip sensors on
the stationary handlebars and your current heart rate is displayed on
the console.
with HeartLogic Intelligence, Octane Fitness’ sophisticated yet easy
to use heart rate control technology. This sophisticated solution
provides the most accurate and effective workout possible using
heart rate data captured by a wireless chest strap or the digital
contact heart rate grip sensors on the stationary handlebars.
The console displays time-in-zone, current heart
rate, heart rate %, and target heart rate so you know exactly where you are and where you should be.
Using a wireless
chest strap
The wireless chest strap transmits your heart rate to the electronics console at a
coded) transmitter. Adjust the length of the elastic strap and fasten the transmitter
Make sure the logo is away from you and right side up. It may help to moisten the
electrodes on the back of the transmitter with a small amount of water for better
contact with the skin. The electrodes are the ribbed portion on the back side of the
transmitter that sits against your skin. Make sure the strap fits snugly but doesn’t
restrict breathing. The contact handgrips reading takes priority if both the wireless
and contact heart rate grips are in use.
Using the digital
contact heart
rate sensors
The digital contact heart rate sensors are located on the stationary handlebars of the
For the
most accurate heart rate reading possible, grasp each contact heart rate grip so that
the contact sensor portion of the grip rests in the palm of your hand. Grip the contact
Heart rate
programs and Heart Rate Custom Interval) to offer you more variety to suit your personal needs.
The 30:30 program also uses heart rate data to provide an assessment of heart rate
recovery. We recommend that you try different programs to determine your favorite.
13
MultiGripHandlebarsthat deliver the ultimate upper-body workout with virtually unlimited
options for maximal comfort, customization, and effectiveness. The
Octane, and these innovative handlebars have revolutionized how you
workout your upper-body. The MultiGrip handlebars are comfortable
in any position, whether you’re hanging on loosely for a brief, easy
workout, or gripping them tightly to complete a lengthy, heart-pumping,
high-intensity workout session.
fit every exerciser—tall, short, slender, large-framed, and even those
with shorter or longer arms—providing a multitude of choices that
result in the most comfortable and ergonomically correct positions of
put to work for you:
Zone 1
Zone 2
Zone 3
Zone 4
Zone 5
Top horizontal position Ideal for pushing
Gives longer range of motion
Large corner position
Widest position Focuses more on using the pectoral (chest) muscles
Wide grip Low inside position Shorter range of motion
Suitable for lighter workouts with less upper-body involvement
Simulates runners movement or when moving fast
Great for pulling or pushing of the arms
Focuses on the lat (back), triceps (back of arm), and biceps (front of arm) muscles
reposition your hands any time during any program for maximal muscle exertion, balance, variety, and comfort.
Learn More at www.octanefitness.com
FUEL YOUR LIFE™
Octane Fitness Octane Fitness International
US & Canada, Latin America, Asia & Asian Pacific Europe, Middle East, Africa
Suite 100 2909 LD, Capelle a/d Ijssel
Fax: 763.323.2064
and SmartStride are registered trademarks of Octane Fitness. Any use of these trademarks, without the express written consent of Octane Fitness, is
forbidden.
Are you passionate about your workout and the results?
Share your story with others on the Octane Fitness web site.
Go to: www.octanefitness.com/testimonials
Then click on “Share My Story” and
show the world how fueled you are.
www.octanefitness.com
www.youtube.com/user/octanefitness
www.facebook.com/octanefitness
Other manuals for PRO 310
2
Table of contents
Other Octane Fitness Elliptical Trainer manuals
Octane Fitness
Octane Fitness Q35c User manual
Octane Fitness
Octane Fitness q47c User manual
Octane Fitness
Octane Fitness Q35 User manual
Octane Fitness
Octane Fitness ZR8 User manual
Octane Fitness
Octane Fitness xRide xR4 User manual
Octane Fitness
Octane Fitness ZERO RUNNER ZR7000 User manual
Octane Fitness
Octane Fitness PRO 310 User manual
Octane Fitness
Octane Fitness PRO3700 Original instructions
Octane Fitness
Octane Fitness Q47e User manual
Octane Fitness
Octane Fitness Q37x User manual
Octane Fitness
Octane Fitness Pro 370 User manual
Octane Fitness
Octane Fitness Q35 User manual
Octane Fitness
Octane Fitness PRO3700 User manual
Octane Fitness
Octane Fitness PRO350 Installation and operating instructions
Octane Fitness
Octane Fitness LATERALXLX8000 Parts list manual
Octane Fitness
Octane Fitness xR6000 User manual
Octane Fitness
Octane Fitness XT User manual
Octane Fitness
Octane Fitness PRO4700 User manual
Octane Fitness
Octane Fitness PRO3700C User manual
Octane Fitness
Octane Fitness Q35 User manual
Popular Elliptical Trainer manuals by other brands
Xterra
Xterra FSX3500 owner's manual
Stairmaster
Stairmaster ClubStride 5100-LE Unpacking and installation instructions
Trojan
Trojan VERTIGO 250 Assembly, care and instructions manual
LifeCore Fitness
LifeCore Fitness LC2000 owner's manual
Keys Fitness
Keys Fitness Triumph 8.3e owner's manual
Reebok
Reebok SL8.0 user manual
Christopeit Sport
Christopeit Sport CS 5 Assembly and exercise instructions
BH FITNESS
BH FITNESS Sprint Elliptical SE4 owner's manual
ICON Health & Fitness
ICON Health & Fitness PRO-FORM 590 E user manual
Vision Fitness
Vision Fitness X6100 owner's guide
Sunny Health & Fitness
Sunny Health & Fitness SF-E320051 user manual
JOHNSON HEALTH TECH.
JOHNSON HEALTH TECH. E8000 owner's manual