Octane Fitness Q35 User manual

2

3
Q35 ASSEMBLY INSTRUCTIONS
PERSONAL RECORD KEEPING
Tip: Record the serial numbers of your Octane Fitness®elliptical in the spaces below. This will make it easier
for you to obtain accurate and timely response should any service issues occur with your elliptical machine.
ATTENTION – All serial numbers begin with a letter.
Base Serial Number – located below front right chrome rail at the power inlet
__ __ __ __ __ __ __ __ __ __ __ __ __ __
Console Serial Number – located on the lower edge of the console
__ __ __ __ __ __ __ __ __ __ __ __ __ __
If you have any additional questions or need additional assistance in assembly, please contact your local service
provider or Octane Fitness Customer Service at 1.888.OCTANE4 ext. 1. You may also visit us on the web at
www.octanefitness.com.
WARNING: Machine contains moving parts. Use caution when assembling and operating this machine.

4
Q35 Contents
The Octane Fitness base box contains the following: Tools required:
 A) 1-OctaneFitnesscrosstrainerbase • Phillipsscrewdriver
 B) 1-Consoleandmast* • 17mmwrenchoradjustablewrench
 C) 1-Topcover • 17mmsocketandratchet
D) 1 - Access panel • 6mmhexkeywrench
E) 1 - Detached right pedal lever
F) 1 - Right moving handlebar
G) 1 - Left moving handlebar
H) 2 - Handlebar covers
I) 1 - Mast boot
J) 1 - Hardware pack
* Note: RoHS-compliant product ships with console and hardware (4 Phillips screws) in a separate box.
D
HI
AB
C
E
F
G

5
Hardware Pack (J) includes:
 K) 8-6mmhexkeychamferedbolt
(for moving handlebar)
 L) 4-Phillipsscrews
(for mounting top shroud and access panel)
M) 1 - Cable tie
(for securing excess cable)
KL
M
The Q35 Power Supply box contains the following:
1) 1 - Powersupply
2) 1 - Information packet
2
1

6
1. Attach pedal lever
a. Remove bolt from 3-pivot link.
b. Place right pedal lever (E) through leg slot in rear shroud and
attach it to the 3-pivot link. Check to see that the rollers are
seated and properly aligned on the rails before securing
the pedal lever.
c. Tighten the bolt and nut securely using 17mm socket and
wrench.
2. Install console mast
a. Assemble the console and mast (B) by placing the keyhole slots
in the mast plate over the bolts and sliding it forward and down
(away from the pedals).
b. Tightenthefour6mmhexkeyboltsattachingconsolemastto
frame.
c. Connectthemaincableconnectorandthemastconnector.Listen
for a click to make sure it is a positive connection.
d. Insert the supplied cable tie (M) through the small hole
to secure the cable to the frame. Push the excess cable
into the console upright tube.
3. Attach arms—Arms are labeled left and right, be sure to
install accordingly.
a. Installmovinghandlebar(ForG)withfour6mmhexkeybolts
(K) on each side—make sure these bolts are very tight.
b. Positionthehandlebarcover(H)overthehandlebarpivotpoint
and press firmly to attach.
c. Repeat for the other side.

7
4. Place top cover
a Placetopcover(C)ontopofmainhousing.Make sure the
steel bracket on the front of the top cover clips on to
the front of the main frame.
b. Securethetopcovertotheframeusing2Phillipsscrews(L).
5. Mount the console to the console mast
Note: If your product was shipped with the console attached,
proceed to step 6.
a. Attach the cable connectors from the console mast tube to
the connections on the back of the console. Listen for clicks
to ensure positive connections. Make sure any excess
cable is pushed into upright tube.
b. Positiontheconsoleontheplateatthetopofthemast(B),
andinsert4Phillipsscrewspartiallythroughthemastplate
into the console back. Tighten screws to secure.
6. Install mast boot
a. Placetherubbermastboot(I)aroundthemast(B).
b. Starting at the front of the machine, tuck the edges of the boot
under the lip of the top cover (C).

8
8. Adjust levelers
a. Adjustallfourlevelerstomakesuretheproductsitsflaton
the floor. For a lower step up height, screw the rear levelers
into the rear stabilizer bracket. Then level the machine using
the front levelers.
b. Tighten the leveler nut against the frame for each leveler.
Note: If you move your Q35, you may need to adjust the
levelers to make sure your product is level with the
floor.
If the unit is not level, it may not function
properly.
7. Install access panel
a. Positiontheaccesspanel(D)byslidingtheroundendsaround
the handlebar connections and the top edge under the top
cover and into the recess of the mast boot (I).
b. Presstheaccesspanelfirmlyintoplaceandsecureittothe
frameontheleftandrightsidesusing2Phillipsscrews(L).

9
Moving the Product
It is safest to move the product to its installation location in its shipping carton. It may be easier to move the
product into your home after you remove it from the packaging, but be careful not to hit any walls or doors.
The Q35 features transport wheels on the front of the unit. Be careful when moving from one surface to another,
such as hardwood floor to carpet.
Note: If you need to pick up your elliptical there are hand placement slots under the front shroud. Please take
caution when lifting. The elliptical weighs approximately 260 lbs. when fully assembled.
Tip: When using the front transport wheels, it is easier to pull the unit rather than push it.
9. Plug in product
a. First,inserttheplugintotheproduct,locatedjustbelow
the right roller track. Next, route the cable toward the wall
outlet. You can run it under the product to avoid seeing it
or tripping on the cable. Ensure that the cord will not be
pinchedandbecomedamaged.Plugtheproductintothe
wall.
Note: There is no need to turn off your product—your
Q35 was designed with an intelligent sleep mode—
a virtual off button. This eliminates the need for an
on/off switch. When your product is in sleep mode,
it uses very little power.

10
NOTES

11
NOTES

FUEL YOUR LIFE™
9200 Wyoming Avenue North, Suite 380
BrooklynPark,MN55445
1.888.OCTANE4
www.octanefitness.com
© 2008 Octane Fitness, LLC™. All rights reserved. Octane Fitness, DedicatedLogic, Fuel Your Life, HeartLogic, Now-Zone and X-Mode are registered
trademarks of Octane Fitness. Any use of these trademarks, without the express written consent of Octane Fitness, is forbidden.
101409-001 REV D
Are you passionate about your workout and the results?
Share your story with others on the Octane Fitness web site.
Go to: www.octanefitness.com/testimonials
Then click on “Share My Story” and
show the world how fueled you are.