OEM Tools 24793 Service manual

WARNING
The following safety information is provided as guidelines to help you operate your Jack under the safest possible conditions. Any tool or piece
of equipment can be potentially dangerous to use when safety or safe handling instructions are not known or not followed. The following safety
instructions are to provide the user with the information necessary for safe use and operation. Please read and retain these instructions for the
continued safe use of your Jack. Failure to follow instructions listed below may result in serious injury. In addition, make certain that anyone
that uses the equipment understands and follows these safety instructions as well.
Explanation of Safety Signal Words
WARNING:Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
CAUTION:Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
CAUTION:Used without the safety alert symbol indicates a potentially hazardous situation which, if not avoided, may
result in property damage.
NOTES:Provide clarity and helpful information.
Thank you very much for choosing an OEMTOOLS®Product!
For future reference, please register your new tool at www.oem-tools.com and complete the owner’s record below:
Model: _______________ Purchase Date: ___________
Save the receipt, warranty and these instructions. It is important that you read the entire manual to become familiar with this product before you begin
using it. This product is designed for certain applications only. OEMTOOLS®cannot be responsible for issues arising from modification. We strongly
recommend that this product is not modified and/or used for any application other than that for which it was designed. If you have any questions relative
to a particular application, DO NOT use the product until you have first contacted customer service to determine if it can or should be performed on the
product.
WARNING:Pursuant to California Proposition 65, this product contains chemicals known to the state of California to cause cancer and birth
defects or other reproductive harm. Wash hands after handling.
Operating Instructions and Parts Manual 24793
Please read and save these instructions. Read through this owner’s manual carefully before using product. Protect yourself and others by observing
all safety information, warnings, and cautions. Failure to comply with instructions could result in personal injury and/or damage to product or property.
Please retain instructions for future reference.
1
7/20
2020 OEMTOOLS®
1,500 LB. MECHANICAL
VEHICLE POSITIONING JACK SET
FOR CUSTOMER SERVICE
Technical Question?
CALL 1-866-458-2472
[email protected]
UNPACKING
After unpacking unit, inspect carefully for any damage that may have
occurred during transit. Check for loose, missing, or damaged parts.
If any damage is observed, a shipping damage claim must be filed
with carrier. Do not use OEMTOOLS®1,500 Lb. Mechanical Vehicle
Positioning Jack Set if broken, bent, cracked or damaged parts
(including labels) are noted. Any Jack that appears damaged in any
way, operates abnormally or is missing parts should be removed from
service immediately. If you suspect that the Jack was subjected to
a shock load (a load that was dropped suddenly, unexpectedly, etc.)
immediately discontinue use until it has been checked by a factory
authorized service center.

2
Operating Instructions and Parts Manual 24793
7/20
2020 OEMTOOLS®
1,500 LB. MECHANICAL
VEHICLE POSITIONING JACK SET
IMPORTANT INSTRUCTIONS
AND SAFETY RULES
1. Know your tool. Read this manual carefully. Learn the tool’s
applications and limitations, as well as potential hazards specific to it.
2. Keep work area clean and well lit. Cluttered or dark work areas
invite accidents.
3. Keep children away. All children should be kept away from the
work area. Never let a child handle a tool without strict adult
supervision.
4. DO NOT operate this tool if under the influence of alcohol or drugs.
Read warning labels on prescriptions to determine if your judgment
or reflexes are impaired while taking drugs. If there is any doubt, do
not attempt to operate.
5. Use safety equipment. Eye protection should be worn at all times
when operating this tool. Use ANSI approved safety glasses.
Everyday eyeglasses are NOT safety glasses. Dust mask, non-skid
safety shoes, hard hat or hearing protection should be used in
appropriate conditions.
6. Wear proper apparel. Loose clothing, gloves, neck- ties, rings,
bracelets or other jewelry may present a potential hazard when
operating this tool. Keep all apparel clear of the tool.
7. Don’t overreach. Keep proper footing and balance at all times when
operating this tool.
8. Check for damage. Check your tool regularly. If part of the tool is
damaged it should be carefully inspected to make sure that it can
perform its intended function correctly. If in doubt, the part should
be repaired. Refer all servicing to a qualified technician. Consult
your dealer for advice.
9. Keep away from flammables. DO NOT attempt to operate this tool
near flammable materials or combustibles. Failure to comply may
cause serious injury or death.
10. Store idle tools out of the reach of children and untrained persons.
Tools may be dangerous in the hands of untrained users.
11. Maintain tools with care.
12. Keep tools dry and clean.
13. Properly maintained tools are less likely to bind and are easier to
control. DO NOT use a damaged tool. Tag damaged tools “DO NOT
USE” until repaired.
14. Check for misalignment or binding of moving parts, breakage of
parts, and any other condition that may affect the tool’s operation.
15. If damaged, have the tool serviced before using. Many accidents
are caused by poorly maintained tools.
16. Use only accessories that are recommended by the manufacturer
for your model. Accessories that may be suitable for one tool may
become hazardous when used on another tool.
17. Tool service must be performed only by qualified repair personnel.
Service or maintenance performed by unqualified personnel could
result in a risk of injury.
18. When servicing a tool, use only identical replacement parts. Use
of unauthorized parts or failure to follow maintenance instructions
may create a risk of injury.
19. Maintain a safe working environment. Keep the work area well lit.
Make sure there is adequate surrounding workspace. Keep the
work area free of obstructions, grease, oil, trash, and other debris.
DO NOT use this product in a damp or wet location.
20. Maintain labels and nameplates on this product. These carry
important information. If unreadable or missing, contact
OEMTOOLS®for a replacement.
21. Keep the handle dry, clean, and free from brake fluid, oil, and
grease.
22. Before use, read and understand all warnings, safety precautions,
and instructions as outlined in the vehicle manufacturer’s service
manual. It is beyond the scope of this manual to properly describe
the correct procedure and test data for each vehicle.
23. Always perform vehicle service in a properly ventilated area. Never
run an engine without proper ventilation for its exhaust. Stop work
and take necessary steps to improve ventilation in the work area
if you develop momentary eye, nose, or throat irritation as this
indicates inadequate ventilation.
24. Engine parts that are in motion and unexpected movement of a
vehicle can injure or kill. When working near moving engine parts,
wear snug fit clothing and keep hands and fingers away from
moving parts. Keep hoses and tools clear of moving parts. Always
stay clear of moving engine parts. Hoses and tools can be thrown
through the air if not kept clear of moving engine parts.
25. The unexpected movement of a vehicle can injure or kill. When
working on vehicles always set the parking brake or block the wheels.
26. Avoid accidental fire and/or explosion. DO NOT smoke near engine
fuel and battery components.
27. The warnings, precautions, and instructions discussed in this
manual cannot cover all possible conditions and situations that
may occur. The operator must understand that common sense and
caution are factors which cannot be built into this product but must
be supplied by the operator.
28. For safety purposes and the prevention of damage to expensive
components it is advised that the user have an understanding of
basic automotive repair and a working knowledge of automotive
systems.
29. We believe the information contained herein to be reliable.
However, general technical information is given by us without
charge and the user shall employ such information at their own
discretion and risk. We assume no responsibility for results or
damages incurred from the use of such information in whole or in
part. Always refer to specific instructions and technical information
supplied by vehicle manufacturer.
30. The manufacturer declines any and all responsibility for damage
to vehicles or components if said damage is the result of unskillful
handling by the operator or of failure to observe the basic safety
rules set forth in the instruction manual.
31. This equipment is intended only for professional use by personnel
trained in performing the service functions for which it is has
been designed.
32. This equipment is designed for servicing a variety of vehicles in a
safe, convenient manner. However, differences in vehicle makes
and models may make it impossible to use this equipment as it is
intended. DO NOT attempt to force the use of this equipment on an
application for which it is not designed to perform.
33. The procedures documented in this manual are to serve as
guidelines for the use of this equipment.
34. In addition to these guidelines, always follow the manufacturer’s
recommended procedures when servicing each unique vehicle.
35. The use of this equipment is simple and straightforward if you
follow the instructions. When operating this equipment, use
common sense, and always stop to think before using a Vehicle
Positioning Jack or lifting a vehicle.
PRODUCT DESCRIPTION
The 1,500 Lb. Mechanical Vehicle Positioning Jack Set is designed for
use on tires to allow vehicle to be maneuvered in any direction. Easy
foot pedal lifting function raises vehicle. Mechanical lift construction
with locking function lifts tires between (2) Rollers. Use on vehicles
weighing up to 6,000 pounds (requires 4 jacks).
NEVER use for any purpose other than those uses outlined above!

3
Operating Instructions and Parts Manual 24793
7/20
2020 OEMTOOLS®
1,500 LB. MECHANICAL
VEHICLE POSITIONING JACK SET
PRODUCT SPECIFICATIONS
Max. Holding Capacity Per Unit 1,500 Lb.
Width Between Arms Closed 13-3/8"
Width Between Arms Open 28"
Max. Wheel Diameter 31-7/8"
Net Weight Per Unit 34.3 Lb.
SPECIFIC SAFETY INSTRUCTIONS
AND WARNINGS
1. Verify that the product and application are compatible; if in doubt
call OEMTOOLS at 866-458-2472.
2. Before using this product, read the operator’s manual completely
and familiarize yourself thoroughly with the product, its
components and recognize the hazards associated with its use.
3. Wear appropriate safety gear, including heavy-duty work gloves
and ANSI-approved safety goggles during use.
4. DO NOT exceed the weight capacity of the Vehicle Positioning Jack
Set. Exceeding the maximum capacity for this product is dangerous
and can lead to serious injury or property damage.
5. Always evaluate your task before using this Vehicle Positioning
Jack Set. Only use as intended.
6. DO NOT use for lifting human weight. Keep clear of raised load.
7. Use only on a hard, level and flat surface capable of bearing the
combined weight of the Vehicle Positioning Jack Set, the load being
lifted, the operator, and any tools being used.
WARNING
8. If you are working and the load becomes off-balance and/or the
jack begins to tip over, DO NOT ATTEMPT TO CATCH OR LIFT THE
LOAD WHEN FALLING. SERIOUS PERSONAL INJURY CAN RESULT! In
this event, clear the area as quickly and safely as possible in order
to avoid injury from the falling load, including getting hit with flying
fragments.
9. Before each use, inspect the general condition of the Vehicle
Positioning Jack Set. If a problem occurs, have the problem corrected
before further use.
WARNING: To prevent serious injury: DO NOT use a damaged or
malfunctioning vehicle positioning jack.
10. If in doubt about the safety of your project, we advise you to have the
work done by a professional familiar with applicable safety practices.
11. This is a lifting device only. Immediately after lifting, support the
vehicle with appropriate means.
12. The use of jack stands is considered the only safe way to work
under or around a vehicle. Only one end or side of the car should be
supported at a time. The wheels not supported need to be choked.
WARNING
Use the jack on a smooth level surface. DO NOT operate the jack on
inclines.
DO NOT use the jack with tires that are wider than 13 inches.
DO NOT start the vehicle’s engine or drive the vehicle with the jack in
use. The jack is designed only for manual maneuvering of a vehicle.
The higher a vehicle is lifted the more unstable it becomes; therefore,
use the lowest possible lock pin position.
ASSEMBLY STEPS
1. Unpack the positioning jacks making sure that all of the parts and
pieces have been included.
2. Find both of the rod assemblies (3) for each positioning jack. Be
prepared to attach one to the ratchet assembly (6) and the other to
the receiver assembly (16).
3. Insert the rod assembly (3) into the roller (5).
4. Press the rod assembly (3) into the ratchet assembly (6). Use the
washer (7), lock washer (8) and bolt (9) to secure everything in
place. Repeat this with the other rod assembly (3) and the receiver
assembly (16).
5. Install caster with lock (10) to ratchet assembly (6) and receiver
assembly (16) using nut (1).
OPERATION INSTRUCTIONS
WARNING: Be fore operating the positioning jack, make sure that
all the hardware is secure, and that each unit has been tested properly.
1. Make sure that the vehicle being lifted is located on a solid flat surface.
2. Slide the positioning jack around the tire so that the rollers (5) are
perpendicular to the tire. Make sure that each tire has a positioning
jack around it before raising.
3. To raise each tire, pump each foot pedal (21) so that the rollers (5)
move together and lift the tire off the ground.
4. IMPORTANT: Once raised to the desired height, press the foot pedal
(21) down and swing the pedal latch (29) up to secure the foot
pedal (21) in place.
5. Once all four tires are resting on the positioning jacks, the vehicle
can be pushed into the desired location.
6. To lower the vehicle, flip lever (19) down and pump foot pedal (21)
until the weight of the vehicle begins to spread the rollers (5) apart
allowing the tire to rest on the ground.
7. Remove the positioning jacks from each tire and secure the foot
pedal (21) with the pedal latch (29).
8. Apply the locking function on the caster (10) when it is necessary.
WARNING: Use caution when troubleshooting a malfunctioning
Vehicle Positioning Jack. Stay well clear of the supported load.
Completely resolve all problems before use. If the Vehicle Positioning
Jack is malfunctioning, have a qualified technician inspect and repair
the Vehicle Positioning Jack before use.
MAINTENANCE
Keep the jack clean and well lubricated. If the jack has been exposed
to rain, snow, sand, or grit, it must be cleaned immediately to prevent
rust and corrosion.
LUBRICATION
A periodic coating of light lubricating oil to pivot points, adjusting
points, etc. will help to prevent rust and assure that all components
move freely.
STORAGE
Always store the Vehicle Positioning Jack Set in a well-protected area
where it will not be exposed to inclement weather, corrosive vapors,
abrasive dust, or any other harmful elements.

4
Operating Instructions and Parts Manual 24793
7/20
2020 OEMTOOLS®
1,500 LB. MECHANICAL
VEHICLE POSITIONING JACK SET
Figure Description Qty.
1Nut 4
2Caster 2
3Roller Axle 2
4Block 6
5Roller 2
6Tube 1
7Washer 2
8Lock Washer 2
9Bolt 2
10 Caster 2
11 Screw 6
12 Claw 1
13 Spring 1
14 Plate 1
15 Limit Block 1
16 Tube 1
17 Bolt 1
18 Plate 1
19 Lock 1
20 Spring 1
21 Pedal 1
22 End Cap 1
23 Pin 1
24 Claw 1
25 Pin 1
26 Cotter Pin 1
27 Nut 1
28 O Ring 1
29 Pin 1
30 Spring 1
31 Washer 1
PRODUCT LAYOUT PARTS LIST
3580 E. Raines Road, Suite 3, Memphis, TN 38118
Tel: [phone]
www.oem-tools.com
OEMTOOLS®90 DAY LIMITED WARRANTY
For up to 90 days from the original purchase of this OEMTOOLS®product, if you find any defect in material or workmanship (through normal usage), return it to the place
of purchase or to OEMTOOLS®for repair or replacement at our discretion. In order to obtain this service, send your tool and proof of purchase (transportation pre-paid) to:
OEMTOOLS®Q.A. Dept., 3580 E. Raines Road #3, Memphis, TN 38118.
We will not be responsible for lost or damaged goods during transportation; please insure your package. If our inspection verifies the defect, we will either repair or
replace the product, or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will return repaired products at our
expense, but if we determine there is no defect, or that the defect resulted from causes not within the scope of our warranty, then you must bear the cost of returning the
product.
OEMTOOLS®does not provide warranty for products labeled other than OEM®or OEMTOOLS®. OEMTOOLS®will not provide any warranty for products subjected to
abnormal use. Abnormal use includes (but is not limited to) abuse, accident, alteration, neglect, and unauthorized or unreasonable use or repairs. This warranty does
not cover bits, blades, files, batteries, or calibration. We recommend that you maintain your tools and sharpen or replace blades, bits, files, and batteries as necessary.
OEMTOOLS®reserves the right to make any changes in construction or design at any time without any obligation in incorporating such changes to tools or equipment
previously sold.
OEMTOOLS®makes every effort to ensure that its products meet high quality and durability standards and warrants to the original purchaser that this product is free from
defects in materials and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly to misuse,
abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installation, normal wear and tear, or to lack of maintenance.
We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent, special or consequential damages arising from the use of our product.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation of exclusion may not apply to you. THIS WARRANTY
IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS. This warranty gives you
specific legal rights, and you may also have other rights, which vary from state to state.
Don’t forget to register your new OEMTOOLS®product at www.oem-tools.com.
CONTACT US
NOTE:Not all components of the Vehicle Positioning Jack are replacement items but are illustrated as a convenient reference for location and
position in the assembly sequence. The manufacturer and/or distributor have provided the parts list and assembly diagram in this manual as a
reference tool only. Neither the manufacturer nor distributor makes any representation or warranty of any kind to the buyer that he or she is
qualified to make any repairs to the product, or that he or she is qualified to replace any parts of the product. In fact, the manufacturer and/or
distributor expressly states that all repairs and parts replacements should be undertaken by certified and licensed technicians and not by the
buyer. The buyer assumes all risk and liability arising out of his or her repairs to the original product or replacement parts thereto, or arising out
of his or her installation of replacement parts thereto.