OEM Tools 24856 Service manual

UNPACKING
After unpacking the unit, inspect carefully for any damage that
may have occurred during transit. Check for loose, missing,
or damaged parts. If any damage is observed, a shipping
damage claim must be filed with the carrier. Do not use
the Vehicle Position Jack Cradle if broken, bent, cracked or
damaged parts (including labels) are noted. Any Jack Cradle
that appears damaged in any way, operates abnormally or is
missing parts should be removed from service immediately.
If you suspect that the Jack Cradle was subjected to a shock
load (a load that was dropped suddenly, unexpectedly, etc.),
immediately discontinue use until it has been checked by a
factory authorized service center.
Please read and save these instructions. Read through this owner’s manual carefully before using product. Protect yourself and
others by observing all safety information, warnings, and cautions. Failure to comply with instructions could result in personal
injury and/or damage to product or property. Please retain instructions for future reference.
The following safety information is provided as a guideline to help you operate your Vehicle Position Jack Cradle under the
safest possible conditions. Any tool or piece of equipment can be potentially dangerous to use when safety or safe handling
instructions are not known or not followed. The following safety instructions are to provide the user with the information
necessary for safe use and operation. Please read and retain these instructions for the continued safe use of your Vehicle
Position Jack Cradle. Failure to follow instructions listed below may result in serious injury. In addition, make sure that anyone
who uses the equipment understands and follows these safety instructions as well.
Operating Instructions and Parts Manual 24856
FOR CUSTOMER SERVICE
Technical Question?
CALL 1-866-458-2472
[email protected]
Thank you very much for choosing an OEMTOOLS™Product!
For future reference, please register your new tool at www.oem-tools.com and complete the owner’s record below:
Model: _______________ Purchase Date: ___________
Save the receipt, warranty and these instructions. It is important that you read the entire manual to become familiar with this product
before you begin using it. This product is designed for certain applications only. OEMTOOLS™cannot be responsible for issues
arising from modification. We strongly recommend that this product is not modified and/or used for any application other than that
for which it was designed. If you have any questions relative to a particular application, DO NOT use the product until you have first
contacted customer service to determine if it can or should be performed on the product.
Explanation of Safety Signal Words
WARNING:Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
CAUTION:Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
CAUTION:Used without the safety alert symbol indicates a potentially hazardous situation which, if not avoided, may
result in property damage.
NOTES:Provide clarity and helpful information.
VEHICLE POSITION
JACK CRADLE
1
7/18
2018 OEMTOOLS™
24856
WARNING

2
Operating Instructions and Parts Manual 24856
7/18
2018 OEMTOOLS™
VEHICLE POSITION
JACK CRADLE
IMPORTANT INSTRUCTIONS
AND SAFETY RULES
1. Know your tool. Read this manual carefully. Learn the
tool’s applications and limitations, as well as potential
hazards specific to it.
2. Keep work area clean and well lit. Cluttered or dark
work areas invite accidents.
3. Keep children away. All children should be kept away
from the work area. Never let a child handle a tool
without strict adult supervision.
4. DO NOT operate this tool if under the influence of
alcohol or drugs. Read warning labels on prescriptions
to determine if your judgment or reflexes are impaired
while taking drugs. If there is any doubt, DO NOT
attempt to operate.
5. Use safety equipment. Eye protection should be
worn at all times when operating this tool. Use ANSI
approved safety glasses. Everyday eyeglasses are NOT
safety glasses. Dust mask, non-skid safety shoes, hard
hat or hearing protection should be used in appropriate
conditions.
6. Wear proper apparel. Loose clothing, gloves, neck-ties,
rings, bracelets or other jewelry may present a potential
hazard when operating this tool. Keep all apparel clear
of the tool.
7. DO NOT overreach. Keep proper footing and balance
at all times when operating this tool.
8. Check for damage. Check your tool regularly. If part of
the tool is damaged, it should be carefully inspected
to make sure that it can perform its intended function
correctly. If in doubt, the part should be repaired. Refer
all servicing to a qualified technician. Consult your
dealer for advice.
9. Keep away from flammables. DO NOT attempt
to operate this tool near flammable materials or
combustibles. Failure to comply may cause serious
injury or death.
10. Store idle tools out of the reach of children and
untrained persons. Tools may be dangerous in the
hands of untrained users.
11. Maintain tools with care.
12. Keep tools dry and clean.
13. DO NOT use a damaged tool. Tag damaged tools
“DO NOT USE” until repaired.
14. Check for misalignment or binding of moving parts,
breakage of parts, and any other condition that may
affect the tool’s operation.
15. Use only accessories that are recommended by the
manufacturer for your model. Accessories that may
be suitable for one tool may become hazardous when
used on another tool.
16. If damaged, have the tool serviced before using. Many
accidents are caused by poorly maintained tools.
17. Tool service must be performed only by qualified repair
personnel. Service or maintenance performed by
unqualified personnel could result in a risk of injury.
18. When servicing a tool, use only identical replacement
parts. Use of unauthorized parts or failure to follow
maintenance instructions may create a risk of injury.
19. Maintain a safe working environment. Keep the work
area well lit. Make sure there is adequate surrounding
workspace. Keep the work area free of obstructions,
grease, oil, trash, and other debris. DO NOT use this
product in a damp or wet location.
20. Maintain labels and nameplates on this product. These
carry important information. If unreadable or missing,
contact OEMTOOLS™ for a replacement.
21. Avoid accidental fire and/or explosion. DO NOT smoke
near engine fuel and battery components.
22. Before use, read and understand all warnings, safety
precautions, and instructions as outlined in the vehicle
manufacturer’s service manual. It is beyond the
scope of this manual to properly describe the correct
procedure and test data for each vehicle.
23. Always perform vehicle service in a properly ventilated
area. Never run an engine without proper ventilation
for its exhaust. Stop work and take necessary steps
to improve ventilation in the work area if you develop
momentary eye, nose, or throat irritation as this
indicates inadequate ventilation.
24. Engine parts that are in motion and unexpected
movement of a vehicle can injure or kill. When working
near moving engine parts, wear snug fit clothing and
keep hands and fingers away from moving parts. Keep
hoses and tools clear of moving parts. Always stay
clear of moving engine parts. Hoses and tools can
be thrown through the air if not kept clear of moving
engine parts.
25. The unexpected movement of a vehicle can injure or
kill. When working on vehicles, always set the parking
brake and chock the wheels.
26. For safety purposes and the prevention of damage to
expensive components, it is advised that the user have
an understanding of basic automotive repair and a
working knowledge of automotive systems.
27. This equipment is intended only for professional use by
personnel trained in performing the service functions
for which it is designed.
28. This equipment is designed for servicing a variety
of vehicles in a safe, convenient manner. However,
differences in vehicle makes and models may make it
impossible to use this equipment as it is intended.
DO NOT attempt to force the use of this equipment on
an application for which it is not designed to perform.

3
Operating Instructions and Parts Manual 24856
7/18
2018 OEMTOOLS™
VEHICLE POSITION
JACK CRADLE
29. The procedures documented in this manual are to
serve as guidelines for the use of this equipment.
30. In addition to these guidelines, always follow the
manufacturer’s recommended procedures when
servicing each unique vehicle.
31. The use of this equipment is simple and straightforward
if you follow the instructions. When operating this
equipment, use common sense and always stop to
think before using this tool.
32. We believe the information contained herein to be
reliable. However, general technical information is given
by us without charge and the user shall employ such
information at their own discretion and risk. We assume
no responsibility for results or damages incurred from
the use of such information in whole or in part. Always
refer to specific instructions and technical information
supplied by the vehicle manufacturer.
NOTE:The manufacturer declines any and all
responsibility for damage to vehicles or components if
said damage is the result of unskillful handling by the
operator or of failure to observe the basic safety rules set
forth in the instruction manual.
WARNING:Carefully read Rules for Safe Operation
and Instructions.
IMPORTANT SAFETY INSTRUCTIONS
The warnings, precautions, and instructions discussed in this
manual cannot cover all possible conditions and situations
that may occur. The operator must understand that common
sense and caution are factors which cannot be built into
this product but must be supplied by the operator.
PURPOSE
The OEMTOOLS™ 24856 Vehicle Position Jack Cradle is
designed to conveniently store 4 Vehicle Position Jacks so
they are safely stored and easily accessible. Keeping the
Jacks on this Cradle when not in use makes for a clean,
professional look and protects the Jacks by keeping them
dry and out of the way of accidental damage.
PRODUCT SPECIFICATIONS
Weight Capacity 300 Lbs.
Ground Clearance 5-1/8" H
Casters 5" x 1" Swivel Black Poly-Plastic
with Steel Frame
Dimensions (LxWxH) 24-7/8" x 31-7/8" x 9-9/16"
ASSEMBLY
Following the diagram (page 4), attach the cross beam
using the bolts and nuts provided and the 4 Casters using
the lock nuts provided.
WARNING:DO NOT place the Vehicle Position Jack
Cradle on an incline or uneven surface. The loaded weight
is over 300 Lbs. and it could roll away unexpectedly and
damage property or cause injury.
OPERATION
Place one Vehicle Position Jack on each of the 4 holders.
MAINTENANCE
1. Clean any oil, grease or dirt from the Jack Cradle.
2. Always store the Jack Cradle in a well-protected area
where it will not be exposed to inclement weather,
corrosive vapors, abrasive dust or any other harmful
elements.
3. Store out of the way so it does not create a trip hazard.
4. When maintaining, use only identical replacement parts.
DISPOSAL
At the end of the useful life of the product, dispose of
the components according to all state, federal and local
regulations.

4
Operating Instructions and Parts Manual 24856
7/18
2018 OEMTOOLS™
VEHICLE POSITION
JACK CRADLE
CONTACT US
3580 E. Raines Road, Suite 3, Memphis, TN 38118
Tel: [phone]
www.oem-tools.com
OEMTOOLS™ 90 DAY LIMITED WARRANTY
For 90 days from the original purchase of this product, OEMTOOLS™will warranty this item. If you find any defect in
material or workmanship, through normal usage, return it to the place of purchase or to OEMTOOLS™for repair or
replacement at our discretion. In order to obtain this service, send your tool and proof of purchase, transportation pre-
paid, to OEMTOOLS™Q.A. Dept., 3850 Raines Road #3, Memphis, TN 38118. We will not be responsible for lost or
damaged goods during transportation; please insure your package. If our inspection verifies the defect, we will either
repair or replace the product, or we may elect to refund the purchase price if we cannot readily and quickly provide you
with a replacement. We will return repaired products at our expense, but if we determine there is no defect, or that the
defect resulted from causes not within the scope of our warranty, then you must bear the cost of returning the product.
OEMTOOLS™does not provide warranty for products labeled other than OEM®or OEMTOOLS™. OEMTOOLS™will
not provide any warranty for products subjected to abnormal use. Abnormal use includes, but is not limited to, abuse,
accident, alteration, neglect, and unauthorized or unreasonable use or repairs. This warranty does not cover bits,
blades, files, batteries, or calibration. We recommend that you maintain your tools and sharpen or replace blades, bits,
files, and batteries as necessary. OEMTOOLS™reserves the right to make any changes in construction or design at
any time without any obligation in incorporating such changes to tools or equipment previously sold.
OEMTOOLS™makes every effort to ensure that its products meet high quality and durability standards, and warrants
to the original purchaser that this product is free from defects in materials and workmanship for the period of 90
days from the date of purchase. This warranty does not apply to damage due directly or indirectly to misuse, abuse,
negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installation, normal wear
and tear or to lack of maintenance.
We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent, special or
consequential damages arising from the use of our product. Some states do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitation of exclusion may not apply to you. THIS WARRANTY
IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF
MERCHANTABILITY AND FITNESS. This warranty gives you specific legal rights, and you may also have other rights,
which vary from state to state.
Don’t forget to register your new OEMTOOLS™product at www.oem-tools.com.
PRODUCT LAYOUT PARTS LIST
Figure Description Qty.
1
Bolt M10 x 30 4
2 Flat Washer #10 4
3 Side Beams 2
4 Nut M12 4
5 Flat Washer #12 8
6 Castors 4
7 Top Covers 4
8 Center Beam 1
NOTE:Not all components of the product are replacement
items but are illustrated as a convenient reference for
location and position in the assembly sequence.
1
2
3
4
5
5
6
7
8
OEMTOOLS™ and/or its distributors have provided the parts list and assembly diagram as a reference only. Neither
OEMTOOLS™ nor its distributors make any representation or warranty of any kind to the buyer and/or user of this
tool that he or she is qualified to do any repairs or replace any parts of this product. OEMTOOLS™ and its distributors
expressly state that all repairs or parts replacement should be done by certified or licensed technicians. The buyer
assumes all risk and liability arising out of his or her repairs or parts replacement to the original production.