OEM Tools 24795 Service manual

WARNING
The following safety information is provided as a guideline to help you operate your 2 Ton Scissor Jack under the safest possible conditions.
Any tool or piece of equipment can be potentially dangerous to use when safety or safe handling instructions are not known or not followed.
The following safety instructions are to provide the user with the information necessary for safe use and operation. Please read and retain
these instructions for the continued safe use of your 2 Ton Scissor Jack. Failure to follow instructions listed below may result in serious injury.
In addition, make sure that anyone who uses the equipment understands and follows these safety instructions as well.
Explanation of Safety Signal Words
WARNING:Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
CAUTION:Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
CAUTION:Used without the safety alert symbol indicates a potentially hazardous situation which, if not avoided, may
result in property damage.
NOTES:Provide clarity and helpful information.
Thank you very much for choosing an OEMTOOLS®Product!
For future reference, please register your new tool at www.oem-tools.com and complete the owner’s record below:
Model: _______________ Purchase Date: ___________
Save the receipt, warranty and these instructions. It is important that you read the entire manual to become familiar with this product before you begin
using it. This product is designed for certain applications only. OEMTOOLS®cannot be responsible for issues arising from modification. We strongly
recommend that this product is not modified and/or used for any application other than that for which it was designed. If you have any questions relative
to a particular application, DO NOT use the product until you have first contacted customer service to determine if it can or should be performed on the
product.
WARNING:Pursuant to California Proposition 65, this product contains chemicals known to the state of California to cause cancer and birth
defects or other reproductive harm. Wash hands after handling.
Operating Instructions and Parts Manual 24795
Please read and save these instructions. Read through this owner’s manual carefully before using product. Protect yourself and others by observing
all safety information, warnings, and cautions. Failure to comply with instructions could result in personal injury and/or damage to product or property.
Please retain instructions for future reference.
1
8/21
2021 OEMTOOLS®
2 TON SCISSOR JACK
UNPACKING
After unpacking the unit, inspect carefully for any damage that may
have occurred during transit. Check for loose, missing, or damaged
parts. If any damage is observed, a shipping damage claim must
be filed with the carrier. DO NOT use the OEMTOOLS®24795 2 Ton
Scissor Jack if broken, bent, cracked or damaged parts (including
labels) are noted. Any 2 Ton Scissor Jack that appears damaged in
any way, operates abnormally or is missing parts should be removed
from service immediately. If you suspect that the 2 Ton Scissor Jack
was subjected to shock load (a load that was dropped suddenly,
unexpectedly, etc.) Immediately discontinue use until it has been
checked by a factory authorized service center.
FOR CUSTOMER SERVICE
Technical Question?
CALL 1-866-458-2472
[email protected]

2
Operating Instructions and Parts Manual 24795
8/21
2021 OEMTOOLS®
2 TON SCISSOR JACK
IMPORTANT INSTRUCTIONS
AND SAFETY RULES
1. Know your tool. Read this manual carefully. Learn the tool’s
applications and limitations, as well as potential hazards specific to it.
2. Keep work area clean and well lit. Cluttered or dark work areas invite
accidents.
3. Keep children away. All children should be kept away from the work
area. Never let a child handle a tool without strict adult supervision.
4. DO NOT operate this tool if under the influence of alcohol or drugs.
Read warning labels on prescriptions to determine if your judgment or
reflexes are impaired while taking drugs. If there is any doubt, DO NOT
attempt to operate.
5. Use safety equipment. Eye protection should be worn at all times
when operating this tool. Use ANSI approved safety glasses. Everyday
eyeglasses are NOT safety glasses. Dust mask, non-skid safety shoes,
hard hat or hearing protection should be used in appropriate conditions.
6. Wear proper apparel. Loose clothing, gloves, neck-ties, rings,
bracelets or other jewelry may present a potential hazard when
operating this tool. Keep all apparel clear of the tool.
7. DO NOT overreach. Keep proper footing and balance at all times when
operating this tool.
8. Check for damage. Check your tool regularly. If part of the tool is
damaged, it should be carefully inspected to make sure it can perform
its intended function correctly. If in doubt, the part should be repaired.
Refer all servicing to a qualified technician. Consult your dealer for
advice.
9. Keep away from flammables. DO NOT attempt to operate this tool
near flammable materials or combustibles. Failure to comply may
cause serious injury or death.
10. Store idle tools out of the reach of children and untrained persons.
Tools may be dangerous in the hands of untrained users.
11. Maintain tools with care.
12. Keep tools dry and clean.
13. Properly maintained tools are less likely to bind and are easier to
control. DO NOT use a damaged tool. Tag damaged tools “DO NOT
use” until repaired.
14. Check for misalignment or binding of moving parts, breakage of parts,
and any other condition that may affect the tool’s operation.
15. If damaged, have the tool serviced before using. Many accidents are caused
by poorly maintained tools.
16. Use only accessories that are recommended by the manufacturer
for your model. Accessories that may be suitable for one tool may
become hazardous when used on another tool.
17. Tool service must be performed only by qualified repair personnel.
Service or maintenance performed by unqualified personnel could
result in a risk of injury.
18. When servicing a tool, use only identical replacement parts. Use of
unauthorized parts or failure to follow maintenance instructions may
create a risk of injury.
19. Maintain a safe working environment. Keep the work area well lit. Make
sure there is adequate surrounding workspace. Keep the work area free
of obstructions, grease, oil, trash, and other debris. DO NOT use this
product in a damp or wet location.
20. Maintain labels and nameplates on this product. These carry
important information. If unreadable or missing, contact OEMTOOLS
®
for a replacement.
21. Keep the handle dry, clean, and free from brake fluid, oil, and grease.
22. Before using, read and understand all warnings, safety precautions,
and instructions as outlined in the vehicle manufacturer’s service
manual. It is beyond the scope of this manual to properly describe the
correct procedure and test data for each vehicle.
23. Always perform vehicle service in a properly ventilated area. Never
run an engine without proper ventilation for its exhaust. Stop work
and take necessary steps to improve ventilation in the work area if
you develop momentary eye, nose, or throat irritation as this indicates
inadequate ventilation.
24. Engine parts that are in motion and unexpected movement of a
vehicle can injure or kill. When working near moving engine parts,
wear snug fit clothing and keep hands and fingers away from moving
parts. Keep hoses and tools clear of moving parts. Always stay clear of
moving engine parts. Hoses and tools can be thrown through the air if
not kept clear of moving engine parts.
25. The unexpected movement of a vehicle can injure or kill. When
working on vehicles, always set the parking brake or chock the
wheels.
26. Avoid accidental fire and/or explosion. DO NOT smoke near engine
fuel and battery components.
27. The warnings, precautions, and instructions discussed in this manual
cannot cover all possible conditions and situations that may occur.
The operator must understand that common sense and caution are
factors which cannot be built into this product, but must be supplied
by the operator.
28. For safety purposes and the prevention of damage to expensive
components, it is advised that the user have an understanding of basic
automotive repair and a working knowledge of automotive systems.
29. We believe the information contained herein to be reliable. However,
general technical information is given by us without charge and the
user shall employ such information at his or her own discretion and
risk. We assume no responsibility for results or damages incurred
from the use of such information in whole or in part. Always refer to
specific instructions and technical information supplied by vehicle
manufacturer.
30. The manufacturer declines any and all responsibility for damage
to vehicles or components if said damage is the result of unskillful
handling by the operator or of failure to observe the basic safety rules
set forth in the instruction manual.
31. This equipment is intended only for professional use by personnel
trained in performing the service functions for which it was designed.
32. This equipment is designed for servicing a variety of vehicles in a
safe, convenient manner. However, differences in vehicle makes
and models may make it impossible to use this equipment as it is
intended.
DO NOT attempt to force the use of this equipment on an application
for which it is not designed to perform.
33. The procedures documented in this manual are to serve as guidelines
for the use of this equipment.
34. In addition to these guidelines, always follow the manufacturer’s
recommended procedures when servicing each unique vehicle.
35. The use of this equipment is simple and straightforward if you follow
the instructions. When operating this equipment, use common sense,
and always stop to think before lifting a vehicle.
PRODUCT DESCRIPTION
This OEMTOOLS®2 Ton Scissor Jack is designed to lift (but not
support) up to the specified capacity when performing service on a
vehicle. It is recommended that this jack is used in conjunction with
appropriately rated jack stands.
PRODUCT SPECIFICATIONS
Product Size 18.9" x 3.78" x 3.86"
Weight Capacity 2 Tons
Min. Height 3-7/8''
Max. Height 17-3/8"
Weight 6 Lb.

3
Operating Instructions and Parts Manual 24795
8/21
2021 OEMTOOLS®
2 TON SCISSOR JACK
SPECIFIC SAFETY INSTRUCTIONS
AND WARNINGS
1. Never use the jack for any purpose other than the information in
this manual.
2. Verify that the product and application are compatible, if in doubt
call OEMTOOLS®at 1-866-458-2472.
3. Before using this product, read the operator’s manual completely
and familiarize yourself thoroughly with the product and its
components, and recognize the hazards associated with its use.
4. Wear appropriate safety gear, including heavy duty work gloves and
ANSI-approved safety goggles during use.
5. Raise and lower the unloaded jack throughout the lifting range
before putting into service to ensure the pump operates smoothly.
Replace worn or damaged parts.
6. DO NOT exceed the weight capacity of the jack. Make sure weight
is evenly distributed. Be aware of dynamic loading! Sudden load
movement may briefly create excess load causing product failure.
Exceeding the maximum capacity for this product is dangerous and
can lead to serious injury or property damage.
7. Always evaluate your task before using this jack. This jack is
designed to lift (but not support) your vehicle. Use only as intended.
8. Never work under a vehicle supported only by a jack.
9. It is recommended that each un-lifted tire be chocked in both
directions.
10. Use only on a hard, level and flat surface capable of bearing the
combined weight of the jack, the load being lifted, the operator and
any tools being used.
11. DO NOT attempt to move or dolly a vehicle with a jack.
12. DO NOT lift or carry the jack by the handle. The handle may
become disconnected resulting in injury or property damage.
13. Before each use, inspect the general condition of the jack. Check
for oil leaks, jack operation, loose components, free rotation and
pivoting of saddle adjustment components. If a problem occurs,
have the problem corrected before further use.
WARNING:DO NOT use a damaged or malfunctioning jack.
14. If in doubt about the safety of your project, we advise you to have the
work done by a professional familiar with applicable safety practices.
BEFORE USE
1. Check before each use for abnormal conditions such as cracked
welds, leaks, damaged, loose or missing parts.
2. Inspect the jack immediately if lift is believed to have been
subjected to an abnormal load or shock.
3. If the jack is found to be damaged, it should be removed from
service until properly repaired.
OPERATING INSTRUCTIONS
WARNING:
1. Study, understand and follow all instructions before operating this
device.
2. IMPORTANT: Before attempting to raise any vehicle, check vehicle
service manual for recommended lifting surfaces.
A. SETUP
There is little or no preparation for the setup of this jack. Make sure
the jack is in its low height position. The handle is used to raise and
lower the jack. Rotating the handle on the jack screw in a clockwise
direction will raise the jack saddle and rotating in a counterclockwise
direction will lower the jack saddle.
B. LIFTING
1. Follow the vehicle manufacturer’s recommended guidelines for
lifting. Engage the emergency brake and chock each un-lifted
wheel in both directions to prevent inadvertent vehicle movement.
2. Insert the jack handle onto the jack screw.
3. Make sure that the saddle is correctly positioned. To prevent
damage to the jack, DO NOT move the jack while the handle is
intact in the socket.
4. To raise the load, use one hand to hold the front part of the handle
on the screw and use the other hand to turn the screw in a
clockwise direction. Raise the load to desired height.
Place jack stands of appropriate capacity under the vehicle.
WARNING:DO NOT CRAWL UNDER VEHICLE WHILE LIFTING
VEHICLE OR PLACING OR REMOVING JACK STANDS!
5. Place jack stands at vehicle manufacturer’s recommended support
areas that provide stable support for the raised vehicle. Once jack
stands are positioned, rotate the screw VERY SLOWLY (by turning
the handle counterclockwise). Lower the load to rest on the jack
stands.
C. LOWERING
WARNING:Clear all tools and personnel before lowering load.
1. Raise load high enough to clear jack stands.
2. Remove jack stands.
WARNING:DO NOT CRAWL UNDER VEHICLE WHILE LIFTING
VEHICLE OR REMOVING THE JACK STANDS!
3. To lower the load, use one hand to hold the front part of the
handle on the screw and use the other hand to turn the screw in a
counterclockwise direction SLOWLY.
CAUTION: Keep hands and feet away from the hinge
mechanism of the jack.
MAINTENANCE
Always store the jack in a well protected area where it will not be
exposed to inclement weather, corrosive vapors, abrasive dust, or any
other harmful elements. The jack must be cleaned of water, snow,
sand, grit, oil, grease or other foreign matter before using.
When jack is not in use, lifting arm should be in full down position.
Always keep jack clean and keep the screw and bearings well
lubricated. Store the handle with care.
LUBRICATION
The jack must be lubricated periodically in order to prevent premature
wearing of parts. A general purpose grease must be applied to the
drive screw. Failure to maintain proper lubrication voids warranty
CLEANING
Every jack owner is responsible for keeping the jack label clean and
readable. Use a mild soap solution to wash external surfaces of the
jack but not the drive screw.

4
Operating Instructions and Parts Manual 24795
8/21
2021 OEMTOOLS®
2 TON SCISSOR JACK
Description Qty.
Saddle 1
Screw 1
Base 1
Jack Handle 1
PRODUCT LAYOUT PARTS LIST
3580 E. Raines Road, Suite 3, Memphis, TN 38118
Tel: [phone]
www.oem-tools.com
OEMTOOLS®1 YEAR WARRANTY
For up to one year from the date of purchase of this OEMTOOLS®product, if you find any defect in material or workmanship (through normal
usage), return it to the place of purchase or to OEMTOOLS®for repair or replacement at our discretion. In order to obtain this service, send the
product and proof of purchase (transportation pre-paid) to:
OEMTOOLS®Q.A. Dept, 3580 E. Raines Road #3, Memphis, TN 38118.
We will not be responsible for lost or damaged goods during transportation; please insure your package. If our inspection verifies the defect,
we will either repair or replace the product, or we may elect to refund the purchase price if we cannot readily and quickly provide you with a
replacement. We will return repaired products at our expense, but if we determine there is no defect, or that the defect resulted from causes
not within the scope of our warranty, then you must bear the cost of returning the product.
OEMTOOLS®does not provide warranty for products labeled other than OEM®or OEMTOOLS®. OEMTOOLS®will not provide any warranty for
products subjected to abnormal use. Abnormal use includes (but is not limited to) abuse, accident, alteration, neglect, and unauthorized or
unreasonable use or repairs. This warranty does not cover bits, blades, files, batteries, or calibration. We recommend that you maintain your
tools and sharpen or replace blades, bits, files, and batteries as necessary. OEMTOOLS®reserves the right to make any changes in construction
or design at any time without any obligation in incorporating such changes to tools or equipment previously sold.
OEMTOOLS®makes every effort to ensure that its products meet high quality and durability standards, and warrants to the original purchaser
that this product is free from defects in materials and workmanship for the period of one year from the date of purchase. This warranty does
not apply to damage due directly or indirectly to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal
activity, improper installation, normal wear and tear, or to lack of maintenance.
We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent, special or consequential damages arising
from the use of our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above
limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS. This warranty gives you specific legal rights, and you may also have other
rights, which vary from state to state.
Don’t forget to register your new OEMTOOLS®product at www.oem-tools.com.
CONTACT US
SCREW BASE
SADDLE
JACK HANDLE
NOTE: Not all components of this jack are replacement items, but are illustrated as a convenient reference for location and position in the assembly
sequence. The manufacturer and/or distributor have provided the parts list and assembly diagram in this manual as a reference tool only. Neither the
manufacturer nor distributor makes any representation or warranty of any kind to the buyer that he or she is qualified to make any repairs to the product,
or that he or she is qualified to replace any parts of the product. In fact, the manufacturer and/or distributor expressly states that all repairs and parts
replacements should be undertaken by certified and licensed technicians, and not by the buyer. The buyer assumes all risk and liability arising out of his
or her repairs to the original product or replacement parts thereto, or arising out of his or her installation of replacement parts thereto.