OHAUS 5000 User manual

Quick Start Guide Defender™5000
Ohaus Corporation www.ohaus.com iDefender™5000 (with T51 Indicators)
ASSEMBLY
Attach Indicator Mounting
and secure Load Cell Cable.
Remove Scale and
Accessories from carton. Attach Indicator to Bracket.
Attach Bracket to Column.
Connect Power Cord to Indicator.
Plug Power Supply to Wall Outlet.
Install Platform.
Adjust leveling feet.
Remove Shipping
Spacers.**
**Not included with
some models. x 4
The T51XW is supplied with a grounded power cable.
Use only with a compatible grounded power outlet.
Calidad & Servicio, Razones de Peso
Calle 23B No. 81A - 62 Modelia PBX: (571) 410 28 48 Fax: [phone] Bogotá, D.C. - Colombia.
www.tecnipesaje.com [email protected] [email protected]

Defender™5000 Quick Start Guide
Defender™5000 (with T51 Indicators) ii Ohaus Corporation www.ohaus.com
SAFETY PRECAUTIONS
For safe and dependable operation of this product, please comply with the following
safety precautions:
•Verify that the input voltage printed on the power Adapter and the plug type matches
the local power supply.
•Make sure that the power cord does not pose an obstacle or tripping hazard.
•Disconnect the product from the power supply when cleaning.
•Do not operate this product in hazardous or unstable environments.
•Do not drop loads on the pan.
•Use only approved accessories and peripherals, as available.
•Operate the product only under ambient conditions specified in the Instruction Manual.
•Service should be performed by authorized personnel only.
CONTROLS
Button
Primary Function
(Short Press) ON/ZERO Turns the Indicator on
If Indicator is on,
sets zero.
PRINT
Sends the current value to
the COM port if AUTOPRINT
is set to Off.
FUNCTION
Initiates an application mode.
Temporarily displays the
active mode’s reference data.
TARE
Performs a tare
operation.
Secondary
Function
(Long Press)
Off
Turns the Indicator off. Units Changes the weighing unit. Mode Allows changing the
application mode.
Press and hold allows
scrolling through modes.
Menu
Enter the User menu.
Menu Function
(Short Press) Yes Accepts the current
setting on the display.
No
Advances to the next menu
or menu item.
Rejects the current setting on
the display and advances to
the next available setting.
Increments the value.
Back
Moves back
to previous menu item.
Decrements the value.
Exit
Exits the User menu.
Aborts a calibration in
progress.
Center of Zero
symbol
Preset Tare,
Tare, Brutto,
Gross symbols
Kilogram, Gram,
Percent, Pound,
Ounce, Pound:
Ounce, Tonne,
Pieces symbols
Capacity label
windo
w
Under, Accept
& Over LEDs
Range symbol
Scale symbol
(
not used
)
Dynamic weighing
symbol
Battery charge
symbol
Stability symbol
Net symbol
Calle 23B No. 81A - 62 Modelia PBX: (571) 410 28 48 Fax: [phone] Bogotá, D.C. - Colombia.
www.tecnipesaje.com [email protected] [email protected]

Quick Start Guide Defender™5000
Ohaus Corporation www.ohaus.com iii Defender™5000 (with T51 Indicators)
OPERATION
On/Off: To turn Indicator on, press ON. Indicator runs a display test,
shows a series of informational displays, and enters active weighing mode.
To turn Indicator off, press and hold Off until OFF appears.
Press ZERO to zero the weight display. Scale must be stable.
Scale zeros automatically at Power On.
Manual Tare: If weighing an item in a container, place empty container on
the scale. Before taring, container’s weight is shown (example 0.5 kg).
Press TARE. Display shows zero.
(If container is removed, display shows container’s weight as negative.)
To clear the Tare value, empty the scale and press TARE.
The display shows gross weight (zero if scale is empty).
Weighing: Place the item to be weighed on the scale.
(Sample shown: 1.5 kg, Gross weight.)
Verify the indicator: place a known mass on the scale and check if the reading is accurate.
If not, calibrate, using the Calibration Guide.
ADDITIONAL OPERATIONS
Changing Units of Measure: Press and hold Units until the desired
measuring unit appears. Only measuring units enabled in the Unit Menu are
displayed. (See back page.)
Printing Data: Press PRINT Units to send displayed data to the communication port.
(Auto-Print Mode must be Off).
Communication parameters in the Print and Communication Menu must be set.
(See Instruction Manual).
Application Modes: Press and hold the Mode button until the desired
application mode appears. WEIGH is default mode.
To have other modes accessible through Mode button, first turn
them On in the MODE menu. (See back page.)
When modes are On, choose by toggling through available options
by pressing Mode.
For details on various application modes, see Instruction Manual.
Weigh
Count
Percent
Dynamic
Checkweigh
Off, On
Off, On
Off, On
Off, Manual
Off, On
Calle 23B No. 81A - 62 Modelia PBX: (571) 410 28 48 Fax: [phone] Bogotá, D.C. - Colombia.
www.tecnipesaje.com [email protected] [email protected]

Defender™5000 Quick Start Guide
Defender™5000 (with T51 Indicators) iv Ohaus Corporation www.ohaus.com
MENU NAVIGATION
Press and hold the Menu button until MENU appears on the display.
Use Yes, No, Back,and Exit to navigate in Menu Mode:
– Yes Allows entry / Accepts displayed setting and advances to next menu item.
– No Skips displayed menu / Rejects setting or item, advances to next available item.
– Back Moves backwards through menus.
– Exit Exits directly to active weighing mode.
MENU STRUCTURE (For more details, see Instruction Manual.)
CALIBRATION SETUP READOUT MODE UNIT GMP PRINT-1
Zero
Span
Linearity
CAL Test
GEO
End CAL
Reset
Range
Capacity
Graduation
Power on Unit
Zero Range
Auto Tare
Retain Weight
Legal For Trade
Beeper Volume
Beeper Signal
Button Beeper
End Setup
Reset
Stable Range
Filter
Auto Zero
Backlight
Auto Off Timer
Gross Indicator
End Readout
Reset
Weigh
Count
Percent
Dynamic
Check Weigh
End Mode
Reset
Kilgram
Pound
Gram
Ounce
Pound Ounce
Tonne
Custom
End Unit
Reset
Date
Time
User ID
Project ID
Scale ID
End GMP
Reset
Stable Print
Auto Print
Content
Layout
End Print-1
PRINT-2 COM1 COM2 I-O LOCK MENU LOCK KEY END
Reset
Stable Print
Auto Print
Content
Layout
End Print-2
Reset
Baud
Parity
Stop
Handshake
Alt. Command
End COM1
Reset
Baud
Parity
Stop
Address
Handshake
Alt. Command
End COM2
Reset
External Input
Input Beep
Relay Output
Stable
End I-O
Reset
Lock Cal
Lock Setup
Lock Readout
Lock Mode
Lock Unit
Lock Print1
Lock Print2
Lock COM1
Lock COM2
Lock GMP
Lock I-O
End Lock Menu
Reset
Lock All
Lock Off
Lock Zero
Lock Print
Lock Unit
Lock Function
Lock Mode
Lock Tare
Lock Menu
End Lock Key
*80252987* P/N 80252987
Calidad & Servicio, Razones de Peso
Calle 23B No. 81A - 62 Modelia PBX: (571) 410 28 48 Fax: [phone] Bogotá, D.C. - Colombia.
www.tecnipesaje.com [email protected] [email protected]