Oliver 4040 User manual

4040 12” Professional Tablesaw
Owner’s Manual
Oliver Machinery M-4040 8/2003
1210 Andover Park East
Tukwila, WA 98188 � Copyright 2003
Fax: [phone] www.olivermachinery.net
Phone: [phone] email: [e-mail]

Warranty
Thank you for your purchase of a genuine Oliver woodworking machine. Oliver Machinery has made
every attempt to provide a machine that is safe and durable.
All Oliver products are guaranteed, to the ORIGINAL RETAIL CUSTOMER, to be free from defects for
TWO YEARS FROM THE DATE OF PURCHASE. Oliver Machinery will repair or replace, at its option,
any component that fails under normal use. Please note that the customer is responsible for returning the
failed component to Oliver Machinery prepaid for inspection.
This warranty does not cover damages caused by misuse, accident, unauthorized repair, alteration or
improper maintenance.
Warning
Read this manual thoroughly before operating the machine. Oliver Machinery disclaims any liability for
machines that have been altered or abused. Oliver Machinery reserves the right to effect at any time,
without prior notice, those alterations to parts, fittings, and accessory equipment which they may deem
necessary for any reason whatsoever.
For More Information
Oliver Machinery is always adding new Industrial Woodworking products to the line. For complete, up-to-
date product information, check with your local Oliver Machinery distributor, or visit
www.olivermachinery.net
2

WARNING
Read this manual completely and observe all warning labels on the machine. Oliver Machinery has made
every attempt to provide a safe, reliable, easy-to-use piece of machinery. Safety, however, is ultimately
the responsibility of the individual machine operator. As with any piece of machinery, the operator must
exercise caution, patience, and common sense to safely run the machine. Before operating this product,
become familiar with the safety rules in the following sections.
 Always keep guards in place and in proper operating condition.
 Use blade guard for every applicable operation including all through cuts. If guard is removed
for special non-through cuts such as dado and rabbet cuts, replace before further use of the
saw.
 Keep hands out of line with the saw blade.
 Use a push stick.
 Do not perform any operation freehand.
 Never reach around or over the saw blade.
1. If you are not properly trained in the use of a tablesaw do not use until the proper training has been
obtained.
2. Read, understand and follow the safety instructions found in this manual. Know the limitations and
hazards associated with this machine.
3. Electrical grounding: Make certain that the machine frame is electrically grounded and that a
ground lead is included in the incoming electrical service. In cases where a cord and plug are used,
make certain that the grounding plug connects to a suitable ground. Follow the grounding procedure
indicated in the National Electrical Code.
4. Eye safety:Wear an approved safety shield, goggles, or glasses to protect eyes. Common
eyeglasses are only impact-resistant, they are not safety glasses.
5. Personal protection: Before operating the machine, remove tie, rings, watch and other jewelry and
roll up sleeves above the elbows. Remove all loose outer clothing and confine long hair. Protective
type footwear should be used. Where the noise exceeds the level of exposure allowed in Section
1910.95 of the OSHA Regulations, use hearing protective devices. Do not wear gloves.
6. Guards: Keep the machine guards in place for every operation for which they can be used. If any
guards are removed for maintenance, DO NOT OPERATE the machine until the guards are
reinstalled.
7. Work area: Keep the floor around the machine clean and free of scrap material, saw dust, oil and
other liquids to minimize the danger of tripping or slipping. Be sure the table is free of all scrap,
foreign material and tools before starting to use the machine. Make certain the work area is well
lighted and that a proper exhaust system is used to minimize dust. Use anti-skid floor strips on the
floor area where the operator normally stands and mark off machine work area. Provide adequate
work space around the machine.
8. Material condition: Do not attempt to saw boards with loose knots or with nails or other foreign
material. Do not attempt to saw twisted, warped, bowed stock.
9. Operator position: Maintain a balanced stance and keep your body under control at all times.
10. Before starting: Before turning on machine, remove all extra equipment such as keys, wrenches,
scraps, and cleaning rags away from the machine.
3

11. Careless acts: Give the work you are doing your undivided attention. Looking around, carrying on a
conversation, and “horseplay” are careless acts that can result in serious injury.
12. Disconnect all power sources: Before performing any service, maintenance, adjustments or when
changing blades. A machine under repair should be RED TAGGED to show it should not be used
until the maintenance is complete.
13. Job completion: If the operator leaves the machine area for any reason, the tablesaw should be
turned "off" and the blade should come to a complete stop before their departure. The key should be
placed in the “off” position, removed and given to a supervisor to prevent any unauthorized use of the
tablesaw.
14. Replacement parts: Use only genuine Oliver Machinery factory authorized replacement parts and
accessories; otherwise the warranty and guarantee is null and void.
15. Misuse: Do not use this Oliver tablesaw for other than its intended use. If used for other purposes,
Oliver disclaims any real or implied warranty and holds itself harmless for any injury or damage which
may result from that use.
16. Drugs, alcohol and medication: Do not operate this machine while under the influence of drugs,
alcohol, or any medication.
17. This machine is deigned for cutting wood products only. Do not use to cut any kind of metal or
substance other then wood.
18. Never start the saw while a workpiece is in contact with the blade.
19. Raise or lower the blade only when the machine has been turned “off” and the blade has come to a
complete stop.
20. Miter Gauge and Rip Fence: Never use the miter gauge and rip fence at the same time.
21. Damaged Saw Blade: Never use a damaged saw blade or one that has been dropped. Check the
saw blade for cracks or missing teeth. Do not use a cracked or dull blade or one with missing teeth.
Make sure the blade is securely locked on the arbor.
22. Make sure the blade is running in the proper direction. Refer to the arrow on the blade. The teeth
should be pointing down when viewing from the front of the saw.
23. Alignment: Check the alignment of the splitter to the blade. Also, check the alignment of the fence
to the miter slot.
24. Health hazards: Some dust created by power sanding, sawing, grinding, drilling and other
construction activities contains chemicals known to cause cancer, birth defects or other reproductive
harm. Some examples of these chemicals are:
 Lead from lead-based paint.
 Crystalline silica from bricks and cement and other masonry products.
 Arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type of work. To reduce
your exposure to these chemicals, work in a well-ventilated area, and work with approved safety
equipment, such as those dust masks that are specifically designed to filter out microscopic particles.
Familiarize yourself with the following safety notices used in this manual:
CAUTION: (This means that if precautions are not heeded, it may result in minor or moderate injury
and/or possible machine damage)
WARNING: (This means that if precautions are not heeded, it could result in serious injury or possibly
even death).
4

Table of Contents Page Number
Warranty........................................................................................................................................................ 2
Warnings ....................................................................................................................................................3-4
Table of Contents.......................................................................................................................................... 5
Specifications ................................................................................................................................................ 5
Contents of the Shipping Containers ............................................................................................................ 6
Uncrating the Machine .................................................................................................................................. 7
Machine Preparation and Setup ................................................................................................................... 7
Extension Wing Assembly............................................................................................................................. 7
Handwheel Assembly.................................................................................................................................... 7
Rail Assembly ............................................................................................................................................8-9
Fence Assembly and Adjustment ............................................................................................................9-10
Adjusting 45� and 90� Stops ..................................................................................................................10-11
Leveling Table Insert................................................................................................................................... 11
Splitter and Blade Guard Assembly .......................................................................................................11-12
Miter Gauge ................................................................................................................................................ 13
Controls....................................................................................................................................................... 13
Dust Collection ............................................................................................................................................ 13
Electrical Connections................................................................................................................................. 14
Replacing the Blade.................................................................................................................................... 14
Changing Arbors ......................................................................................................................................... 15
Replacing and Tensioning V-Belt................................................................................................................ 15
Maintenance................................................................................................................................................ 16
Troubleshooting .....................................................................................................................................16-17
Specifications
Model Number......................................................................................................................................... 4040
Stock No. - 4040.003 ....................................................................................................5HP, 1Ph, 220V Only
Stock No. - 4040.004 ..........................................................................5HP, 3Ph, 220V/440V Prewired 220V
Blade Diameter (In) ..................................................................................................................................... 12
Arbor Diameter (In) ............................................................................................... 1" or 5/8" interchangeable
Maximum Width of Dado (In) ................................................................................................................13/16”
Maximum Depth of Cut at 90 Degrees (In) ..................................................................................................4"
Maximum Depth of Cut at 45 Degrees (In) ............................................................................................2-3/4"
Maximum Cut to the Right of Blade ...........................................................................................................36”
Maximum Cut to the Left of Blade..............................................................................................................18”
Dust Port Diameter (In) ................................................................................................................................. 4
Table Dimensions w/Extensions (LxW) ............................................................................... 30-3/4" x 42-1/2"
Table Height (In) ......................................................................................................................................... 36
Blade Tilt ................................................................................................................................................... Left
Arbor Speed RPM.................................................................................................................................. 3,450
Overall Dimensions .............................................................................................. 30-3/4L x 42-1/2"W x 42"H
Gross Weight ............................................................................................................................................ 530
5

Contents of the Shipping Containers
Oliver 4040 – 12” Professional Tablesaw
1. 12” Left Tilt Tablesaw
1. Miter Gauge
4. Wrenches
1. 5/8” Arbor
1. Arbor Nut
2. Handles
Extension Wing Assembly
2. Extension Wings
6. M10-1.5Px30 Hex Head Bolts
6. M10 Lock Washers
Guard Support Assembly
1. Guard Bracket
1. Guard Bracket Rod
1. Guard Mounting Bolt
2. Hex Nuts
1. Lock Washer
1. Flat Washer
1. M8-1.25x35 Hex Head Bolt
1. M8 Lock Washer
Fence and Rail Assembly
1. Fence
1. Guide Tube
2. End Caps
1. Rear Rail
1. Blade Guard Assembly
1. Support
7. Guide Tube Brackets
5. Rear Rail Brackets
7. M8-1.5Px16 Carriage Bolts
7. Lock Washers
7. M8-1.25P Cap Nuts
12. M10-1.5Px16 Flat Head Socket Bolts
7. M10-1.5Px20 Hex Head Bolts
11. M10 Lock Washers
4. M10 Hex Nuts
2. M6-1Px10 Socket Head Cap Screw
6

Uncrating the Machine
Uncrate the machine and inspect the unit for
signs of shipping damage. If damage is found,
contact your dealer immediately. Retain all
packaging materials in case it becomes
necessary to ship the machine to another site.
Machine Preparation and Setup
WARNING!
The equipment used to lift this machine must
have a rated capacity at, or above the weight
of the tablesaw. Failure to comply may
cause serious injury!
The tablesaw must be positioned on a smooth,
level surface. The area must be well lit and
have plenty of room to maneuver with large
pieces of wood.
Level the saw front to back and side to side
using a level placed on the table. Use shims
under the corners, if necessary, but make sure
the saw is stable before being placed into
service.
Clean all rust protected surfaces with a
commercial solvent. Do not use acetone,
gasoline, lacquer thinner or any type of
flammable solvent, or a cleaner that may
damage paint. Cover cleaned surfaces with
WD-40 or a 20W machine oil.
Pay particular attention to cleaning in the miter
slot and the faces of table and extension wing.
Extension Wing Assembly
1. Attach extension wing (A, Figure 1) to table
with three M10x30 hex head bolts, and three
M10 lock washers (B, Figure 1). Snug but
do not tighten. Note: Start with the center
hole (C, Figure 1) to hold the wing in place.
2. Slide extension wing toward the front edge
of the saw table until two edges are flush.
3. Using a straight edge (D, Figure. 2), align
extension wing to saw table and tighten hex
cap bolts. Repeat for opposite wing.
Handwheel Assembly
1. Thread handle (E, Figure 3) into handwheel
(F, Figure 3). Note: There is a flat on the
handle so it can be tightened with a wrench.
7

Rail Assembly
1. Place a M8x16 carriage bolt (A, Figure 4)
through the bracket (B, Figure 4) and hold in
place with a M8 lock washer and M8 cap nut
(C, Figure 4). Note: Just thread the cap nut
onto carriage bolt a couple turns to hold in
place. Leaving the bolt loose will make it
easier to insert the head of carriage bolt into
guide rail slot.
2. Angle the head of carriage bolt into the
keyed slot found on the bottom of guide
tube. Slide in place to engage square
shoulder of carriage bolt with slot and
tighten cap nut.
3. Once all of the brackets have been attached
to the guide tube (D, Figure 4) mount the
brackets to table using seven M10x16 flat
head socket bolts (E, Figure 5).
4. Mount the rear rail brackets (F, Figure 6) to
the table with five M10x16 flat head socket
bolts (G, Figure 6). Leave loose at this time.
5. Mount the rear rail (H, Figure 6) to the
brackets with five M10 lock washers and five
M10x20 hex head bolts (I, Figure 6).
6. Thread two M6x10 socket head cap screws
(J, Figure 6) into the rear rail at both ends.
They act as a stop for the fence.
8

7. Mount the support (A, Figure 7) between the
guide rail and the rear rail. Attach the front
side with two M10x16 flat head socket bolts,
two M10 lock washers and two M10 hex
nuts (B, Figure 7).
8. Attach the rear side with two M10x20 hex
head bolts, two M10 lock washers and two
M10 hex nuts.
Fence Assembly and Adjustment
1. Tilt rear end of the fence (C, Figure 8) down
to engage clip (D, Figure 8) on to the rear
rail and lower the fence on to guide rail, as
shown in Figure 8.
2. Move the fence so that the line on the cursor
(E, Figure 9) reads 2” and lock the fence in
place by pushing down on the handle (F,
Figure 8).
3. Place a ruler (G, Figure 9) on the table and
measure from the right side of the saw blade
tooth to the fence. It should read 2”. If not
move the fence so that it is measures 2”
from the blade. Lock the fence in place and
adjust the cursor by loosening the cursor
screws (H, Figure 9) and adjust to read 2”.
Note: If you do not have enough
adjustment in the cursor loosen cap nuts
that attach the brackets to the guide tube
and slide the tube left or right to get the
proper adjustment. Tighten the cap nuts.
9

4. Move the fence into position so that the
fence and the miter gauge slot align as
shown in Figure 10. The fence should be
parallel to the miter gauge slot. If not loosen
the four screws (A, Figure 10).
Adjusting 45and 90 Stops
The stops have been adjusted at the factory and
should not need any adjustment. If you need to
adjust the stops:
1. Disconnect saw from power source.
2. Raise the saw blade to its maximum height
by turning the blade raising handwheel
clockwise as far as it will go.
3. Set the blade at 90 to the table by turning
the blade tilting handwheel clockwise as far
as it will go.
4. Place a square (B, Figure 11) on the table
and check to see that the blade is at a
90angle to the table, as shown in Figure
11. Make sure ruler is in-between the blade
teeth.
5. If blade is not 90 open the motor cover
door, and loosen hex nuts (B, Figure 12).
6. Turn adjusting stop bolts (C, Figure 12) on
the trunnion in, or out. The adjusting stop
bolts should rest against the table when
blade is 90to the table.
7. Tighten the hex nuts (B, Figure 12) while
holding the adjusting stop bolts (C, Figure
12) to keep them from moving.
8. Check the accuracy of the pointer and adjust
if necessary. It should read 0 on the angle
scale.
10

9. Set the blade 45 to the table by turning the
blade tilting handwheel counter-clockwise as
far as it will go. Place a combination square
on the table and check to see that the blade
is at a 45angle to the table.
10. If the blade is not 45, remove raising and
lowering handwheel by unscrewing the
handwheel lock and loosening the two set
screws in the handwheel hub, as shown in
Figure 13.
11. Loosen hex nut (A, Figure 13) and turn
adjusting stop bolt (B, Figure 13) on the front
trunnion in, or out. The adjusting stop screw
should stop against the front trunnion
bracket when blade is 45to table.
12. Tighten the hex nut (A, Figure 13) while
holding the adjusting stop bolt (B, Figure 13)
to keep it from moving.
13. Check the accuracy of the pointer and adjust
if necessary. It should read 45 on the
angle scale.
Leveling Table Insert
Adjust the table insert flush with the table by
turning four leveling screws (C, Figure 14).
Place a straight edge across the table and
insert. Raise the insert until it just touches the
straight edge. Check both the front and rear
section of the insert.
Splitter and Blade Guard Assembly
1. Disconnect saw from power source.
2. Remove table insert by loosening the screw
at the front of insert. Pull up and towards
you to release the rear clip.
3. Thread blade guard shaft (D, Figure 15) into
rear trunnion through opening at rear of saw.
Use the flat detent at the end of shaft to
tighten blade guard shaft.
4. Place bracket assembly (E, Figure 15) on to
the shaft and thread a M8x35 hex head bolt
and a M8 lock washer (F, Figure 15) into the
bracket.
5. Thread the guard support assembly (G,
Figure 15) into the bracket.
11

6. Insert front fork of blade guard assembly (A,
Figure 16) through opening in the table. The
tab is held in place between the flat washer
and bracket, see Figure 16. Finger tighten
hex nut (B, Figure 16) only at this time.
7. Insert the rear fork of the blade guard
assembly (C, Figure 16) into the guard
support assembly between the flat washer
and shoulder, see Figure 16. Finger tighten
hex nut (D, Figure 16) only at this time.
8. Place a straight edge against the splitter and
blade to make sure they align, as shown in
Figure 17. If adjustment is necessary use
the provided wrench to loosen the jam nut
(E, Figure 18) on the rear fork. Thread the
guard support in, or out by turning the hex
head (F, Figure 18) to bring the splitter in
line with the blade. Repeat the same
procedure for front fork.
9. Tighten the jam nut (E, Figure 18) and
tighten the hex nut (D, Figure 16) with the
provided wrenches. Repeat the same
procedure for front fork. Recheck the splitter
alignment and adjust if necessary.
12

Miter Gauge
1. Slide the miter gauge bar into the miter
gauge slot in table. Loosen the handle (A,
Figure 19) and pull out indexing rod (B,
Figure 19) to pivot the miter gauge body.
2. Push the indexing rod in to engage the
preset stops (C, Figure 19).
3. Adjust stops by loosening the hex nut (D,
Figure 19) and adjusting screw (E, Figure
19).
Note: Always make test cuts. The scale is for
reference. There are two holes in the miter
gauge fence used to attach a wooden fence.
Controls
A. Emergency Stop Button: Stops all
functions of machine, but the saw still has
power. To reset rotate switch clockwise until
the button pops out.
B. Start: Starts saw blade rotation. Will not
work if the “Emergency Stop” switch is
engaged, or the key is in the “OFF” position.
C. Main Control: Turn key to the “OFF”
position and remove from the lock. The key
should be given to a supervisor when the
saw is not in use by an authorized user.
D. Handwheel Lock: There is a handwheel
lock on both handwheels. Loosen lock to
turn handwheel and tighten when blade is in
desired location.
E. Raising and Lowering Handwheel:
Loosen handwheel lock. Turn handle
clockwise to raise the blade. The blade
should be 1/8”-1/4” above the top of
workpiece, or 3-5 blade teeth above the top
of workpiece.
F. Tilting Handwheel: Loosen handwheel
lock. Turn handle counter-clockwise to tilt
blade to the left.
Dust Collection
There is a 4” dust port (G, Figure 21) located on
the side of saw cabinet. Make sure dust
collection system has sufficient capacity and
suction for your tablesaw. Always turn on dust
collection system before starting the tablesaw.
13

Electrical Connections 4. Replace the blade followed by the flange
and arbor nut. Tighten the arbor nut while
holding the arbor in place.
WARNING!
Electrical connections and wiring must be
done by a qualified electrician. The machine
must be properly grounded. Failure to
comply may cause serious injury!
Note: Make sure the blade and arbor are clean
before installing a new blade. The blade teeth
should point down when viewing from the front
of saw.
This saw is available in both 1-Phase and 3-
Phase versions.
 Electrical Connections for a 3-Phase Unit
This saw is 3-Phase, 220V/440V pre-wired
220V. If you need to switch the tablesaw from
220V to 440V have a qualified electrician make
the changes. Oliver Machinery recommends
using a dedicated circuit.
Make sure the voltage of your power supply
matches the specifications on the motor plate of
the machine.
With 3-Phase power verify the blade is turning in
the proper direction. Turn the saw on and make
sure the direction of the blade spins toward the
user when standing in front of the saw. If it does
not, disconnect the power source and reverse
any two power leads.
 Electrical Connections for a 1-Phase Unit
This saw is 1-Phase, 220V only. Oliver
Machinery recommends using a dedicated
circuit.
Make sure the voltage of your power supply
matches the specifications on the motor plate of
the machine.
Replacing the Blade
The blade guard has been removed for photos,
but it is possible to change the blade without
removing the blade guard.
1. Disconnect saw from power source.
2. Remove the table insert and raise the blade
completely.
3. Use the two provided arbor wrenches to
loosen the arbor nut, as shown in Figure 22.
Place one wrench on the arbor nut and one
on the flats located on the arbor. Remove
the nut, flange and blade.
14

Changing Arbors
The blade guard has been removed for photos,
but it is possible to change the blade without
removing the blade guard.
1. Disconnect saw from power source.
2. Remove the table insert and raise the blade
completely.
3. Use the two provided arbor wrenches to
loosen the arbor nut, as shown in Figure 22.
Place one wrench on the arbor nut and one
on the flats located on the arbor. Remove
the nut, flange and blade.
4. Unscrew the socket head cap screw (A,
Figure 23) found in the center of the
interchangeable arbor while holding the
arbor as shown in Figure 23.
5. Remove the interchangeable arbor and
replace with a new one. Screw the socket
head cap screw (A, Figure 23) into the new
arbor, as shown in Figure 24. Note: Always
clean the mating surfaces before installing
the interchangeable arbors.
6. Replace the blade followed by the flange
and arbor nut. Tighten the arbor nut while
holding the arbor in place.
Replacing and Tensioning V-Belt
1. Disconnect saw from power source.
2. Lower the blade to its lowest position and
open the motor cover door.
3. Loosen two hex nuts (B, Figure 25).
4. Take tension off of the belts (C, Figure 25)
by lifting up on the motor.
5. Remove belts from the arbor and motor
pulleys.
6. Replace and tension the belts. The weight
of the motor should apply sufficient tension
to belts. Tighten the hex nuts (B, Figure 25).
7. Check the belt tension after the saw has
been used for a few hours. Adjust as
necessary.
15

Maintenance Use a wire brush to clean trunnions and worm
gears. Apply white lithium grease or powdered
graphite to lubricate worm gears, and trunnions.
WARNING!
Disconnect the machine from power source
before proceeding with any maintenance, or
troubleshooting! Failure to comply may
cause serious injury!
Keep pulleys and belts free from dirt, dust, oil
and grease.
Replace worn v-belts as needed.
Remove rust from the tabletop with WD-40 and
a Scotch-Brite™ Hand Pad. Keep a light coat of
WD-40�on the table top when not in use.
Periodically clean the inside of the machine for
dust control. Use an air hose to blow out dust
from motor fan and motor cover.
Troubleshooting
Description of Symptoms Possible Cause Corrective Action
Machine will not start
1. Fuse blown or circuit breaker
tripped
2. Cord Damaged
3. Faulty switch
4. Not connected to power
source
5. Connected to wrong voltage
6. Key in the “OFF” position
7. Emergency stop button
pressed
1. Replace fuse or reset circuit
breaker
2. Have cord replaced
3. Replace switch
4. Check connection
5. Check voltage
6. Insert key and turn to “ON”
position
7. Rotate emergency stop button
clockwise until it pops out
Blade does not come up to speed
1. Cable too light or too long
2. Low current
3. Motor not wired for correct
voltage
1. Replace with adequate size
cable
2. Contact local electric
company
3. Refer to motor nameplate for
correct voltage
Does not make accurate 45° or
90° cuts
1. Stops not adjusted correctly
2. Angle pointer not set
accurately
3. Miter gauge out of adjustment
1. Check blade with combination
square and adjust stops
2. Check blade with combination
square and adjust pointer
3. Adjust miter gauge
Saw makes unsatisfactory cuts
1. Dull blade
2. Blade mounted backwards
3. Gum or pitch on blade
4. Incorrect blade for cut
1. Sharpen or replace blade
2. Turn blade around
3. Remove blade and clean
4. Change blade to correct type
Material binds blade when ripping
1. Fence not aligned with blade
2. Warped wood
3. Excessive feed rate
4. Splitter not aligned with blade
1. Check and adjust fence
2. Select another piece of wood
3. Reduce feed rate
4. Align splitter with blade
16

17
Saw vibrates excessively
1. Stand on uneven floor
2. Damaged saw blade
3. Bad V-belts
4. Bent pulley
5. Improper motor mounting
6. Loose hardware
1. Reposition on flat, level
surface
2. Replace saw blade
3. Replace V-belts
4. Replace pulley
5. Check and adjust motor
6. Tighten hardware
Material kicked back from blade
1. Rip fence out of alignment
2. Splitter not aligned with blade
3. Feeding stock without rip
fence
4. Splitter not in place
5. Dull blade
6. Letting go of material before it
is past blade
7. Anti-kick back paws dull
1. Align rip fence with miter slot
2. Align splitter with blade
3. Install and use rip fence
4. Install and use splitter (with
guard)
5. Replace blade
6. Push material all the way past
blade before releasing work
7. Replace or sharpen anti-kick
back paws
Blade does not raise or tilt freely Sawdust and debris in raising
and tilting mechanisms Clean and regrease

Sub.No. KeyNo. PartNo. Description Specification Qʼty
1 TJ0106 SpreaderAssʼy 1
1.1 TJ010001 Spreader 1
1.2 TJ010003 GuardBracket 1
1.3 TJ010005 Bracket-Crank 4
1.4 TJ010002 spacer 2
1.5 TJ010006 BladeGuardSide 2
1.6 TJ010008 Anti-KickPawlL 1
1.7 TJ010004 Anti-KickPawlR 1
1.8 TJ010007 BladeGuardFront 1
1.9 OE090103 TopCover 1
1.10 OE090108 GuardFrontBracket 1
1.11 OE090109 Collar 8
1.12 TJ010081 Spring 1
1.13 TH010040 FixCollar 2
1.14 TJ010014 Pin 1
1.15 HA050405 FlatHDPhil.Bolt M6*1.0P*12染黑 4
1.16 HA080310 SocketHDBolt M5*0.8P*20染黑 8
1.17 HA080412 SocketHDBolt M6*1.0P*24染黑 2
1.18 HG011232 springPin 8*55 1
1.19 HG011018 springPin 5*32 1
1.20 HG011111 springPin 6*20 1
1.21 HC040600 NylockNut M6*1.0P染黑 2
1.22 HC040500 NylockNut M5*0.8P染黑 8
1.23 HE012000 FlatWasher 6.5*23*3t染黑 8
1.24 HF060400 PushNut SPN-6 2
2 TJ0107 FenceAssʼy 1
2.1 TJ010009 FenceHolder 1
2.2 TJ010010 FenceHolderBracket 1
2.3 TJ010012 Shaft 1
2.4 TJ010011 ClampingPlate 1
2.5 TJ010013 Spring 1
2.6 TJ010015 RailSilder 2
2.7 TJ010017 Fence 1
2.8 TJ010021 Indicator 2
2.9 TJ010018 LockPlate 1
2.10 TJ010020 FenceEndCap 1
2.11 TJ010022 ClampingCam 1
2.12 TJ010023 Handle  1
2.13 TJ010024 HandleCap 1
2.14 HA020406 RoundHDPhil.Screw M6*1.0P*16染黑 2
2.15 HA260400 RoundHDPhil.Screww/washer M5*0.8P*10染黑 4
2.16 HA180313 RoundHDPhil.Screw M4*1.59P*25染黑 4
2.17 HA180405 RoundHDPhil.Screw M5*2.12P*12染黑 1