olympia electronics BAU LIGHT Series User manual

The light source contained in this luminary shall only be replaced by the manufacturer, or his
agent, or a similar qualified person.
NOTE! The light source is non-user replaceable.
NOTE!! The installer should fill in, on the specification
label, the letter G if the luminaire is used as a safety sign.
(*) Maintained operation: The luminaire lights its illumination source, when it is powered by the mains
power supply or not.
Non Maintained operation: The luminaire lights its illumination source, only in power supply’s failure.
ADDRESS OPERATION
For address operations refer to the installation
manual of the panel. Please see manual of CBS
panel GR-8600 for maximum number of
luminaries that can be interconnected.
GENERAL
1. Operations for installation, maintainance or
testing must be done by authorized personnel
only.
2. The device, must be connected only to the
GR-8600 panel via its ADR line.
3. The user must set the address before
installation. To address the device see on page
3.
Thank you for your trust in our products
Olympia Electronics - European manufacturer
923753002_09_002
TECHNICAL CHARACTERISTICS (for LED MODULE Specifications see page 1)
Operation temperature range
Relative humidity
Construction materials
External dimensions
Typical weight
Guarantee
Mains voltage
Maximum power consumption
Degrees of cover protection
Produced in accordance with
Light source intensity
18-30V DC
o
-30 to 50 C
up to 95%
3 years
IP 54
200lm
2.5W
ABS/PC, PC
551 gr.
EN 60598-1, EN 60598-2-22, ΕΝ 55015, ΕΝ 61547
Page 1 from 3
LED MODULE CHARACTERISTICS
Olympia Electronics S.A
45 °C max. across the board
Manufacturer
Model Number
Voltage Range
Connections
Nominal Power
Temperature (tc)
NOTE: LED= Light Emitting Diode
LABELING EXPLANATION:
Z: Central supply
1: Maintained (*)
C: Including inhibiting mode
G: Internally illuminated safety sign
12-14V DC
2.4W
2505195
“BAU LIGHT” SERIES ADDRESSABLE LUMINARIES FOR GR-8600 CBS
GR-750/CBS/24V/ADR/HP/LL GR-751/CBS/24V/ADR/LP/LL GR-752/CBS/24V/ADR/HP/HL GR-753/CBS/24V/ADR/LP/HL
1.5W
350lm
Viewing distance *15m, **17m 15m 15m
358 x 85 x 88 mm358 x 125 x 88 mm 358 x 85 x 88 mm 358 x 125 x 88 mm
579 gr. 579 gr. 551 gr.
12-13.5V DC
1.1W
Non-reversible connection between main pcb and led module
35 °C max. across the board
Z1C
*15m, **17m
GR-750/CBS/24V/ADR/HP/LL GR-751/CBS/24V/ADR/LP/LL GR-752/CBS/24V/ADR/HP/HL GR-753/CBS/24V/ADR/LP/HL
*15m: When the luminary is installed on a wall.
**17m: When luminary is installed on the ceiling.

Page 2 from 3
Luminary Installation Procedure
923753002_09_002
WARRANTY
Olympia Electronics guarantees the quality, condition and operation of the goods. The period of warranty
is specified in the official catalogue of Olympia Electronics and also in the technical leaflet, which
accompanies each product. This warranty ceases to exist if the buyer does not follow the technical
instructions included in official documents given by Olympia Electronics or if the buyer modifies the goods
provided or has any repairs or re-setting done by a third party, unless Olympia Electronics has fully
agreed to them in writing. Products that have been damaged can be returned to the premises of our
company for repair or replacement, as long as the warranty period is valid.
Olympia Electronics reserves the right to repair or to replace the returned goods and to or not charge the
buyer depending on the reason of defection. Olympia Electronics reserves the right to charge or not the
buyer the transportation cost.
HEAD OFFICE
72nd km. O.N.R. Thessaloniki-Katerini
P.C. 60300 P.O. Box 06 Εginio Pierias Greece
www.olympia-electronics.gr
[email protected]
1 Place a flat blade screwdriver to the plastic hook and pull up gently to release the diffusor.
2 Remove the reflector.
3 Remove the led strip.
4 Use the included mounting parts to mount the base plastic.
5 Always use round mains cable, with a suitable diameter to fit tightly into the gasket.
ATTENTION!! The cable must not be deformed in any way (This requirement is
important to ensure the ΙΡ rating). Always refer to GR-8600 manual regarding to the
cable’s cross section’s selection. Install the included gasket into the cable entry hole (verify
that is not deformed). Make a hole in the center by using a small screwdriver. Pass the
communication cables through the hole and connect them as shown on the picture (minding
the correct polarity). When there are other luminaries to be connected to the line we
recommend to open a second hole to pass the second pair of communication cables.
6 If the luminary you installed is the last one, connect the cable to one of the two inputs, as
shown on the picture (minding the correct polarity).
7 Address the device though the dipswitch according to the table on page 3.
8 Refit the led strip minding the connection with the P.C.B.
Warning!! The holes of the led strip must be fit in the projections of the base.
9 Refit the reflector (mind the correct orientation) and tighten the screws.
10 Refit the diffusor (mind the correct orientation) and power on the device. (see GR-8600
manual).
Page 3 from 3
Addressing Table
Address Dipswitch
setting AddressAddressAddress Dipswitch setting
Dipswitch
setting
Dipswitch
setting
5
6
7
8
9
10
1
1
1
1
1
1
ON
ON
ON
ON
ON
ON
2
2
2
2
2
2
3
3
3
3
3
3
4
4
4
4
4
4
5
5
5
5
5
5
6
6
6
6
6
6
11
12
13
14
15
16
17
18
19
20
1
1
1
1
1
1
1
1
1
1
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
4
4
4
5
5
5
5
5
5
5
5
5
5
6
6
6
6
6
6
6
6
6
6
21
22
23
24
25
26
27
28
29
30
1
1
1
1
1
1
1
1
1
1
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
4
4
4
5
5
5
5
5
5
5
5
5
5
6
6
6
6
6
6
6
6
6
6
1
ON
2 3 4 5 6
1
ON
2 3 4 5 6
1
ON
2 3 4 5 6
2
3
4
1
ON
2 3 4 5 6
131
32
1
ON
2 3 4 5 6
1
ON
2 3 4 5 6
923753002_09_002
6
5
-L
+L
-L
+L
-L
+L
14
98